Table of Contents
Advertisement
Internal circuit ................................................ 3-20
Internal current consumption .......................... 3-3
Internal information 1 .................................... 13-8
Internal information 2 .................................... 13-8
Interpolation axis ........................................... 9-19
Interpolation control....................................... 9-19
Interpolation speed designation method (
....................................................................... 5-34
Interrupt request during continuous operation
(
Cd.32
) ....................................................... 5-120
[J]
JOG (explanation of terms).............. Appendix-35
JOG operation ............................................... 11-4
JOG operation acceleration time selection
(
Pr.33
) ......................................................... 5-37
JOG operation deceleration time selection
(
Pr.34
) ......................................................... 5-37
JOG operation program ................................ 6-16
JOG operation start time chart.................... 11-11
JOG operation timing and processing times
....................................................................... 11-6
JOG speed (
Cd.19
) ................................... 5-114
JOG speed limit value (
JOG start signal............................................. 3-14
JUMP command............................................ 9-59
[K]
kPPS (explanation of terms) ............ Appendix-35
[L]
LED display function ..................................... 13-7
LIMIT SWITCH (explanation of terms)
.......................................................... Appendix-35
LIMIT SWITCH OUTPUT (explanation of terms)
.......................................................... Appendix-35
LINEAR INTERPOLATION (explanation of terms)
.......................................................... Appendix-35
LOW-INERTIA MOTOR (explanation of terms)
.......................................................... Appendix-36
Last executed positioning data No.(
..................................................................... 5-102
List of condition data ..................................... 5-75
List of configuration devices............................ 2-4
List of control data ....................................... 5-104
List of devices.................................................. 6-4
List of errors................................................... 14-6
List of functions................................................ 3-4
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
Pr.21
)
Pr.32
).................... 5-37
Md.52
)
Index - 5
List of input/output signal details ...................3-18
List of input/output signals .............................3-12
List of monitor data ........................................5-80
List of parameters ..........................................5-18
List of positioning data ...................................5-56
List of start block data....................................5-71
List of warnings ............................................14-30
Logic selection for pulse output to the drive unit
(
Pr.24
)..........................................................5-35
Lower limit ......................................................3-19
[M]
M CODE (explanation of terms) .......Appendix-36
M code OFF request....................................12-59
M code OFF request (
M code ON signal ..........................................3-13
M code ON signal output timing (
M code ON/OFF timing................................12-58
M code output function ................................12-58
M code/condition data (
MACHINE FEED VALUE (explanation of terms)
...........................................................Appendix-36
MANUAL PULSE GENERATOR
(explanation of terms) .......................Appendix-36
MASTER AXIS (explanation of terms)
...........................................................Appendix-36
MOVEMENT AMOUNT PER PULSE
(explanation of terms) .......................Appendix-36
MULTI-PHASE PULSE (explanation of terms)
...........................................................Appendix-36
MULTIPLYING RATE SETTING
(explanation of terms) .......................Appendix-36
Machine feed value........................................9-15
Machine feed value (
Md.30
Machine zero point return................................8-4
Machine zero point return method ..................8-5
Main functions ..................................................3-6
Main positioning control ...................................9-2
Manual control ...............................................11-2
Manual pulse generator.......................... A-16,2-4
Manual pulse generator 1 pulse input
magnification (
Cd.23
).................................5-116
Manual pulse generator enable flag (
......................................................................5-116
Manual pulse generator operation ..............11-17
Manual pulse generator operation program
........................................................................6-16
Cd.14
).....................5-110
Pr.19
).....5-32
Da.9
) ....................5-68
) ........................5-90
Cd.22
)
Advertisement
Table of Contents
Troubleshooting
