And Mode Zones; Wireless Receivers - Bentel Security KYO 320 Installation Manual

AND Mode Zones

This option will allow you to set up the system to gener-
ate Alarms when violation occurs on a specific group of
Zones within a set time.
No. This field shows the Identifier number of the AND
Zone group.
Window This field will allow you to set the time within
which ALL the Zones of the respective group must de-
tect violation.
The And Zones page will allow you to set up to 32
Groups, each with:
Ø up to 8 Zones
Ø a set time (Window) within which ALL the Zones in
the respective Group must detect violation.
From Standby status, each Group will operate as fol-
lows: violation of any of the Zones in the Group will not
generate an Alarm but will start the programmed Win-
dow.
If ALL the Zones in a specific Group detect violation
within the programmed window, the system will gener-
ate the respective Zone Alarms, and will indicate the
Zones concerned on the Keypad.
If NOT ALL the Zones in the Group detect violation
within the programmed Window, the system will refresh
the window and restore to Standby.
After generating a Zone Group Alarm, the system will
be unable to generate further Alarm cycles until ALL the
AND Zones concerned restore to Standby.
'Reset Partition Alarm', 'Arm/Disarm Partition' or 'Stop
Partition Alarm' operations will restore ALL the AND
Zones of the Partition concerned to standby.
The Zones of a Group need not have Partitions in common.
AND Zones can be set up via PC only.

Wireless Receivers

Systems with two VectorRX-8, VRX32-433
or VRX32-868 Receivers can manage up to
64 Wireless Zones and up to 32 keyFobs
(with two vectorRX-8 up to 16 Zones and up
to 16 KeyFobs). With two VRX32 receivers,
up to 64 zones via radio and up to 32 radio
keys.
The Wireless Zones support the following De-
tectors:
Ø AMD20 / KMD20 / KMD20NP - Wireless
Pet-immune Infrared Detector
Ø AMC30 / KMC10 - Wireless Magnetic Con-
tact
Ø AGB10 - Wireless Glass Break Detector
Ø ASD20 / KSD20 - Wireless Optical Smoke
Detector
42
+
Wireless Devices other than those listed above are
not supported by the Vector Receivers. Read the
"APPENDIX" for further information on the listed
Devices.
The system can detect Alarm, Tamper, Low Battery and
Lost Wireless Detectors.
When a Wireless Detector (assigned to a Wireless
Zone) detects Alarm conditions, the system will gener-
ate the respective Alarm on zone no. - Wireless event,
and other events which depend on the programmed
"Type" (refer to "Type" under "Hardwired Zones").
When a Wireless Detector (assigned to a Wireless
Zone) detects Tamper conditions, the system will gen-
erate the respective Tamper on zone no. - Wireless
event, and other events which depend on the pro-
grammed "Type" (refer to "Type" under "Hardwired
Zones").
When the battery of a Wireless Detector (assigned to a
Wireless Zone) is Low, the system will generate a
Warning low battery on wireless device event . This
event will not identify the Wireless detector concerned.
However, the respective information will be recorded in
the log as follows:
Ø TYPE - Low Battery
Ø ID. EVENT - Description of the Wireless Zone no.
When a Wireless Detector fails to transmit, the system will
generate a Lost wireless zone event. The Wireless detec-
tor concerned will not be identified. However, the respec-
tive information will be recorded in the log as follows:
Ø TYPE - Wireless Device Disapp.
Ø ID. EVENT - Description of the Wireless Zone
Wireless keys can Arm in Stay/Away mode and The
Wireless page will allow you to program the Wireless
Zone, as follows.
Figure 28 Wireless Page
KYO 320