Digital Keys - Bentel Security KYO 320 Installation Manual

9. Enable the Code on the Partitions (refer to "Enabling
Partitions and A, B, C and D Mode" under "Using the
Keypad"), then press ENTER.
A arm.mode
AAAAAAAA
10. Setup the A Arming mode configuration (refer to
"Enabling Partitions and A, B, C and D Mode" under
"Using the Keypad"), then press ENTER.
A arm.mode
IDNDDADD
In the example above, the Code concerned will Arm
partition 1 in Instant mode, Arm partition 6 in Away
mode, Disarm partitions 2, 4, 5, 7 and 8 but will not af-
fect partition 3 .
11. Program B, C and D Arming modes. The procedure
is the same as for A Arming mode. If you press ENTER
whilst you programming D Arming mode, you will go to
the next step.
Options
Duress -
12. Using A or B, scroll for the required option: Duress
(refer to "Duress Code"), Patrol (refer to "Patrol Code")
or Available, then press ON or OFF to enable/disable
the option concerned. Press ENTER to confirm and go
to step 13. (if the Available option is enabled), or step
14. (if the Available option is enabled).
+
An 'Available' Code will become 'Active' automa-
tically, if its ID number is lower than 131 (131 not in-
cluded) for KYO 320, it will become the sole Father
Code of itself. If the Code ID number is higher than
131 (131 included) for KYO 320, the system will as-
sign the first 'Available' Code as its Father Code.
+
You cannot change the status of an Active Code
from Enrolled (able to perform its enabled fun-
ctions) to Unenrolled (unable to perform its ena-
bled functions) until it has been Disabled via the
User menu (this operation can be carried out by its
Father Codes only).
+
Each code can have up to 3 Father codes. A code
can be programmed as its own Father. By default,
Code 001 is its own Father. Codes 002 to 131 have
two Father codes: themselves and code 001. Co-
des 132 to 195 (Telephone access codes) have
one Father code, that is, code 001. Codes 132 to
195 cannot be programmed as Father codes.
Father PIN
PIN: xxxxxx
13. To disable a code (make NOT Active), enter the PIN of
a valid Father Code, then press ENTER and go back to
step 3.
12
1_8
1_8
?
+
The "Father PIN?" prompt will remain on the di-
splay until you enter a valid PIN.
Father 1 N. 001
Code
14. Using A or B, select the code to be programmed as Father
Code 1, or enter the Code ID number.
16. Press ENTER to save Father Code 1, then program Fat-
her Code 2 and Father Code 3. Press ENTER to save Fat-
her Code 3, and go to step 3.

Digital Keys

To program the Digital keys, refer to "Keys" under "Con-
trol Panel Programming". The Digital Keys option will
allow you to enrol Digital keys.
From the Installer menu:
INSTALLER MENU
Event logger
1.Using A or B, select the Digital Keys option:
INSTALLER MENU
Digital keys
2. Press ENTER.
Reader : 01
Reader 001
The top line of the display will show the ID number of the
first Reader in the configuration, while the bottom line
will show the Reader label (Description).
+
At least one Reader must be enrolled in order to
provide this option.
3. Using A or B, select the Reader that you intend to
use for the enrolling procedure:
Reader : 02
Reader 002
4. Press ENTER.
Digital key: 001
Digital key
5. Using A or B ,select the key to be enrolled, then press
ENTER. The key label (Description) will blink to indicate
that the system is ready to enrol the key, hold it in the vi-
cinity of a Proximity Reader). When the system has en-
rolled, and consequently enabled the key, the GREEN
LED will turn ON and the system will go to the next Key
and allow you to continue. To step back to the Installer
menu, press ESC.
001
001
KYO320