Lost Installer Codes; Codes - Code Types; User Codes - Bentel Security KYO 320 Installation Manual

The four Installer Codes can be made Activated as re-
quired, and programmed to perform a limited number of
programming and maintenance operations.
+
The Installer Code can program and change all pa-
rameters via computer.
The Installers page will allow you to program Installer
code attributes, as follows.
+
You cannot program an Installer Code without first
entering its Father Installer Code PIN.
The Installer Code hierarchy is set at factory and
CANNOT be changed:
Ø Installer codes no. 196, 197, 198 and 199 have two
Father codes which cannot be changed: themselves
and Code no. 200;
Ø Code no. 200 is its own Father code and cannot be
changed.
The Table on the left side of the Installers page shows
the 5 Installer Codes . The page layout is as follows:
No. Refer to "No." in the "Keypad codes - Users" section.
Description Refer to "Description" in the "Keypad
codes - Users" section.
On the right side of the Installers page you can set the
parameters for the Codes selected on the left side of the
page, as described below.
Active Refer to "Active" in the "Keypad codes - Users"
section.
+
The Active status of Installer Code no. 200 is irre-
versible.
Father PIN Refer to "Father PIN" in the "Keypad
codes - Users" section.
+
At default the Installer Code PIN is 0 followed by
the Code ID Number. For KYO320 for example, the
PIN of Code no. 200 is 0200;
New PIN Refer to "New PIN" in the "Keypad
codes - Users" section.
Redigit New PIN Refer to "Redigit New PIN" in the
"Keypad codes - Users" section.
Code Type Refer to "Code Type" in the "Keypad
codes - Users" section.
+
The Installer Code type CANNOT be changed.
The Code Type for Installer Codes no. 196 and 197 is
Install. Type 1 and CANNOT be changed.
The Code Type for Installer Codes no. 198 and 199 is
Install. Type 2 and CANNOT be changed.
The Code Type for Installer Codes no. 200 is a MASTER
and CANNOT be changed.
80
n Lost Installer Codes
For the instructions on how to restore the default PIN 0200
for KYO320, refer to the "Restore Default Settings" paragraph.
!
If the Installer Codes Lock option is enabled
(refer to "Options"), restoral of the default set-
tings WILL NOT restore the Installer Code PIN.
NOTE: If this occurs, contact your Service dealler.

Codes - Code Types

When programming the Codes, you must also select
which functions are to be enabled.
The system manages 19 Code Types:
Ø 16 User Codes
Ø 2 Installer Codes
+
Code Type 19 is reserved for Installer Code No.
200 , and CANNOT be programmed.
The Code Types page will allow you to select the User
Code and Installer Code functions, as follows.
On the left side of the Code Types page is a Table with
a list of the 19 Code types.
No. This is the Code Type ID Number:
Ø Code Types no. 01 to 16 are reserved for User
Codes;
Ø Code Types no. 17 and 18 are reserved for Installer
Codes;
Ø Code Type no. 19 is reserved for Installer Code No.
200 and CANNOT be programmed.
Description This editable field (16 characters) is for the
label that will identify the Code Type. The label will be used
in the Code Type on the Users and Installers pages.
The functions of the Code Type (selected from the
Code Type list) can be programmed on the right side of
the page.
The User Code functions are described in the following
paragraph.
The Installer Code functions are described in the "In-
staller Codes" paragraph.
n User Codes
This paragraph provides a general description of the
User Code functions — refer to the USER'S MANUAL
for further information.
+
The Partition related functions will affect ONLY
those Partitions common to both the Code and
Keypad in use.
Panel Reset This operation will:
KYO 320