Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Bentel Security KYO Series
Summary of Contents for Bentel Security KYO Series
- Page 1 Unit PROGRAMMING FROM KEYPAD ® MADE ITALY...
- Page 2 The Manual Release Number of each Manual is shown at the bottom of the last page, between the Code and Date, ad indicated in the figure below. Manual Release Number ISTPTBLEUNKYO 190303 P70 Code Date BENTEL SECURITY srl reserves the right to modify the technical specifications of this product without prior notice.
-
Page 3: Table Of Contents
® ® ABLE OF ONTENTS Programming from the Keypad ........4 Introduction ..................4 Code Limitations ..............4 Accepted Keypads ..............5 Enrolling an LCD Keypad at address 8 ........6 Adjusting Contrast, Brightness and Volume (MIA-S/MIA-D) ..6 The Liquid Crystal Display (LCD) ........... 7 Customizing the System .............. -
Page 4: Programming From The Keypad
® ® Multifunction Control Panel ROGRAMMING FROM THE EYPAD Introduction You can program the system using the ‘KyoUnit’ Software Application and a computer (refer to the “INSTALLATION MANUAL”), or using the LCD Keypad. This manual contains instructions regarding system programming via Keypad. For information regarding the system parameters, refer to ‘PROGRAMMING FROM PC’... -
Page 5: Accepted Keypads
® ® Programming from the Keypad Accepted Keypads You can program the system using OMNIA/TAST-R, MIA-S and MIA-D Keypads. The function keys on these Keypads differ slightly, Table 2 shows the Key Equivalence on the various Keypads. Read this section carefully so you know how to operate your system from the Keypad. NOTE: The ‘Superkeys’... -
Page 6: Enrolling An Lcd Keypad At Address 8
® ® Multifunction Control Panel Enrolling an LCD Keypad at Address 08 To enroll an LCD Keypad at Address 08 from a LED Keypad, enter: <Installer Code> + E E + 0 for KYO 32 Series: <Installer Code> + E for KYO 4 - 8 Series: A short beep will indicate that the LCD Keypad has been enrolled. -
Page 7: The Liquid Crystal Display (Lcd)
® ® Programming from the Keypad The Liquid Crystal Display (LCD) During Standby status the display will show: 1st line: Date and Time 2nd line: Partition status (4 or 8 Partitions depending on the system). This line will also show: Trouble and Tamper —... -
Page 8: Customizing The System
® ® Multifunction Control Panel Customizing the System Installer Menu Options The Installer’s Code will allow you to access the INSTALLER MENU and program the following options: Actions (Event Logger, Zones Status, Test Siren, Clear Call Queue) Zones Outputs Times (Entry/Exit Times) Inst.Cod (Installer Code) Keys (Key/Card and Wireless) Codes (User Codes) -
Page 9: Programming
® ® Programming from the Keypad Wrong Code If you enter a Wrong Code the display will show an WRONG CODE error message, and go back to Standby status. Exiting Programming To exit Programming: e e e e e 1. Press (as many times as necessary) to step back on the menu;... -
Page 10: Zones
® ® Multifunction Control Panel Zones 9 9 9 9 9 0 0 0 0 0 1. From the Installer Menu, using , select PROGRAMMING E E E E E the Zones option, then press Zones âá 9 9 9 9 9 0 0 0 0 0 E E E E E Selecting the Zone... - Page 11 ® ® Programming from the Keypad 9 9 9 9 9 0 0 0 0 0 Balance 6. Using , select the Balance type, Zone 2 E E E E E thepress âá ‘Vibration’ or ‘Roller NOTE: If you assign the ‘Vibration’ or ‘Roller Blind’ attribute to the Zone, you must select one of the following Balance types: Blind’...
-
Page 12: Outputs
® ® Multifunction Control Panel Outputs 9 9 9 9 9 0 0 0 0 0 1. From the Installer Menu, using , select PROGRAMMING E E E E E the Outputs option, then press Outputs âá 9 9 9 9 9 0 0 0 0 0 E E E E E 2. -
Page 13: Times
If you select Patrol, Listen, Alarm or Superv., go to step 3a. If you select Inactiv. or Neglig., go to step 3b. If you select Partitions, go to step 3c. NOTE - The Superv. Option is provided by KYO Series 32 Control panels ONLY. E E E E E Programming times: 3a. -
Page 14: Installer Code
® ® Multifunction Control Panel Installer Code 9 9 9 9 9 0 0 0 0 0 1. From the Installer Menu, using , select PROGRAMMING E E E E E the Inst. Cod option, then press Inst.Cod âá 2. Enter the New Installer Code (4 to 6 digits) then Inst.Cod E E E E E press... -
Page 15: Wireless Option
® ® Programming from the Keypad number (e.g. 009) c) by fast blinking on all 3 Reader LEDs e e e e e 9a. Press 4 times to go back to step 3. If the system does not Enroll the Key/Card (due to malfunction or because the system has reached its limit of 128 keys) the Keypad will emit an audible error signal (Bop). -
Page 16: Codes
® ® Multifunction Control Panel Codes 9 9 9 9 9 0 0 0 0 0 1. From the Installer Menu, using , select PROGRAMMING E E E E E the Codes option, then press Codes âá 9 9 9 9 9 0 0 0 0 0 2. -
Page 17: Readers
® ® Programming from the Keypad Readers 9 9 9 9 9 0 0 0 0 0 1. From the Installer Menu, using , select PROGRAMMING E E E E E the Readers option, then press Readers âá 9 9 9 9 9 0 0 0 0 0 Selecting the Reader 2. -
Page 18: Keypads
® ® Multifunction Control Panel Keypads 9 9 9 9 9 0 0 0 0 0 1. From the Installer Menu, using , select PROGRAMMING E E E E E the Keypads option, then press Keypads âá 9 9 9 9 9 0 0 0 0 0 2. -
Page 19: Date/Time
® ® Programming from the Keypad Date/Time 9 9 9 9 9 0 0 0 0 0 1. From the Installer Menu, using , select PROGRAMMING E E E E E the Date/T. option, then press Date/T. âá A A A A A B B B B B 2. -
Page 20: Telephone
® ® Multifunction Control Panel Telephone 9 9 9 9 9 0 0 0 0 0 1. From the Installer Menu, using , select PROGRAMMING E E E E E the Teleph. option, then press Teleph. âá 9 9 9 9 9 0 0 0 0 0 2. -
Page 21: Teleservice
® ® Programming from the Keypad Teleservice 9 9 9 9 9 0 0 0 0 0 1. From the Installer Menu, using , select PROGRAMMING E E E E E the Teleser. option, then press Teleser. âá 9 9 9 9 9 0 0 0 0 0 2. -
Page 22: Events
® ® Multifunction Control Panel Events 9 9 9 9 9 0 0 0 0 0 1. From the Installer Menu, using , select PROGRAMMING E E E E E the Events option, then press Events âá A A A A A B B B B B E E E E E 2. -
Page 23: Options
® ® Programming from the Keypad Options 9 9 9 9 9 0 0 0 0 0 1. From the Installer menu, using , select PROGRAMMING E E E E E Options, then press Options 9 9 9 9 9 0 0 0 0 0 2. -
Page 24: Strings
® ® Multifunction Control Panel Strings This option will allow you to customize the descriptions of the system peripherals, etc. 1. From the Installer Menu, select the Strings PROGRAMMING E E E E E option, then press Strings âá 9 9 9 9 9 0 0 0 0 0 2. -
Page 25: Default
® ® Programming from the Keypad Default G G G G G - The default option will allow you to reset the Control panel to Factory Default, and delete the Events List. 1. From the Installer Menu, select the Default PROGRAMMING E E E E E option, then press... -
Page 26: Input Expanders (Only For Series 32 Models)
® ® Multifunction Control Panel Input Expanders (only for Series 32 Models) This option is available on Serie 32 Models, and will allow you to program the Input Expanders. 9 9 9 9 9 0 0 0 0 0 1. From the Installer Menu, using , select PROGRAMMING E E E E E... -
Page 27: Notes
® ® OTES... - Page 28 ® ® BENTEL SECURITY S.r.l. - C.da Ravigliano, Z.I. S. Scolastica - 64013 CORROPOLI - TE - ITALY Tel.: +39 0861 839060 - Fax: +39 0861 839065 E-mail: info@bentelsecurity.com - http://www.bentelsecurity.com ISTPTBLEUNKYO 1.1 260603 P70...
Need help?
Do you have a question about the KYO Series and is the answer not in the manual?
Questions and answers