Installer Codes; Digital Keys - Bentel Security KYO 320 Installation Manual

ber of operations) will refresh automatically when the
Key is deactivated.
Enable Timers Control If this option is enabled, the
Code will be able to Enable/Disable the Timers selected
in the 'Controllable Timers' section.
Clear phone queue on Partition in stop/reset If this
option is enabled, outgoing calls — triggered by events
associated with the Code Partitions — will be aborted
when the Code is used to stop/reset Alarms.
Clear phone queue on Panel in stop/reset If this op-
tion is enabled, outgoing calls — triggered by events as-
sociated with the Control panel — will be aborted when
the Code is used to stop/reset Alarms (refer to the Ta-
ble 7 on page 61).
Clear phone queue on disarming If this option is en-
abled, outgoing calls — triggered by events associated
with the Code Partitions — will be aborted when the
Code is used to Disarm the system.
Reset Partition Alarms If this option is enabled, Resets
Partition Alarm operations requested by the Codes will:
Ø terminate all Partition Events (refer to Table 6 on
page 60) and Zone Events (refer to Table 5 on
page 59) associated with the Code Partitions;
Ø restore to standby the Outputs associated with the
terminated events (refer to the previous points);
Ø delete Generic Partitions and Partitions Tamper
Alarms generated by the Code Partitions.
+
If the Alarm conditions are still present after Reset
(approx. 2 seconds), the Control panel will trigger
the respective Alarm Events again.
Stop Partition Alarms As for Reset Partition Alarms
but for the Stop Alarms option.
NOTE: If this option is enabled, the events listed in the
previous paragraph will be ignored.
Arming A with User Code If this option is enabled, the
Code will be able to perform A Mode Arming operations.
Arming B with User Code If this option is enabled, the
Code will be able to perform B Mode Arming operations.
Arming C with User Code If this option is enabled,
the Code will be able to perform C Mode Arming opera-
tions.
Arming D with User Code If this option is enabled,
the Code will be able to perform D Mode Arming opera-
tions.
Away Arming with User Code If this option is en-
abled, the Code will be able to Arm all the Partitions com-
mon to both the Code and Keypad in use in Away mode.
82
Disarming with User Code If this option is enabled,
the Code will be able to Disarm all the Partitions com-
mon to both the Code and Keypad in use.
n Installer Codes
This paragraph provides a general description of the func-
tions that can be performed by the Installer Codes: refer to
the KEYPAD PROGRAMMING MANUAL for details.
View Log If this option is enabled, the Code will be
able to view and print the events recorded in the log.
+
This feature is provided by the optional K3/PRT2
Printer Interface (refer to "Printer Interface" in the
APPENDIX). Only the enabled events will be
printed (refer to "Log — Events setup").
Zone Status If this option is enabled, the Code will be
able to view the status (Standby, Alarm, Short, Tamper,
Bypass) of all the Control Panel Zones, and the per-
centage of the Voltage value.
Zone Test If this option is enabled, the Code will be
able to Test all the Control Panel Zones.
Output Test If this option is enabled, the Code will be
able to Stop all the Control Panel Outputs.
Clear Call Queue If this option is enabled, the Code
will be able to clear the Call Queue.
Voice Functions If this option is enabled, the Code
will be able to record and listen to Voice Messages.
Change Installer PIN If this option is enabled, the
Code will be able to change its own PIN, and the PINs of
its assigned codes (sons).
User Codes If this option is enabled, the Code will be
able to program the User codes from the Keypad.
Digital Keys If this option is enabled, the Code will be
able to the Digital Keys from the Keypad.
Panel Programming If this option is enabled, the Code
will be able to program the Control Panel from the Keypad.
Enrol Wireless If this option is enabled, the Code will be
able to enrol Wireless Devices from the Keypad.
Keypad Broadcast If this option is enabled, the Code
will be able to edit the Keypad strings.
Change date/time If this option is enabled, the Code
will be able to change the system Date and Time from
the Keypad.

Digital keys

The Digital Keys page will allow you to program the pa-
rameters of the Digital Keys, as follows.
KYO 320