Keypad Operations; Introduction; Using The Keypad - Bentel Security KYO 320 Installation Manual
Expandable multifunction control panel
Hide thumbs
Also See for KYO 320:
- Installation manual (100 pages) ,
- User manual (28 pages) ,
- Installation manual (52 pages)
Table of Contents
Advertisement
Introduction
You can operate your system from PREMIUM LCD and
CLASSIKA LCD keypads, using the following options:
Event logger: this option will allow you to view the
Event Logger.
Zone status: this option will allow you to view the zone
status and level.
Zone test: this option will allow you to test the functio-
nality of zones without generating alarms.
Output test: this option will allow you to activate/test
preset Outputs.
Clear call queue: this option will allow you to stop out-
going Alarm calls.
Voice functions: this option will allow you to Record/
Playback voice messages (requires K3/VOX2 kit).
Installer PIN: this option will allow you to program the
Installer Code PINs.
User codes: this option will allow you to program the
User code attributes.
Digital keys: this option will allow you to enrol electro-
nic keys.
Program panel: this option will allow you to program
the Control panel parameters.
Enrol wireless: this option will allow you to enrol wireless
detectors, keys and cards and carry out placement tests.
Update strings: this option will allow you to update the
PREMIUM LCd and CLASSIKA LCD keypad strings.
Change time/date: this option will allow you to set the
Control panel clock.
Release: this option will allow you to view the Control
panel release.
Test Keypad: this option will allow you to test the di-
splay, LEDs and buzzer.
Reset warning lithium: this option will allow you to cle-
ar the battery fault signal.
+
The following options and parameters
NOTE:
CANNOT BE programmed from Keypads:— the
Sensitivity of the hardwired zones; the Contact
ID, and SIA code of Digital Communicator, —the
Scheduler parameters, except for Max. no. over-
time Requests and Overtime Request;
—the Timers;
—Enable Keypad Codes/Keys/Cards (LCD/LED
Keypads);
The following operations CAN BE DONE from Key-
pads ONLY:
—Record and Playback Voice Messages;
—Request Log printout;
—Enrol/Unenrol the K-NET module.
KYO320
KEYPAD OPERATIONS
Using the keypad
Read the following section carefully, to get an overall
view of how to use the Function keys.
Function keys
Unless otherwise stated, the keys operate as follows:
A and B scroll the menus;
C and D move along the display lines;
ON and OFF enable/disable options instantly;
ESC quits the entry and steps back;
ENTER saves the entry and allows you to continue.
Audible signalling
Buzz: this is the audible error signal emitted by the key-
pad when commands are denied.
Parameter Descriptions
This manual describes how to program and operate the
Control panel from a keypad.
A complete description of the system functions and pa-
rameters can be found in the INSTALLATION
MANUAL. Indications as where to look in the
INSTALLATION MANUAL are shown in brackets (the
parts underlined in inverted commas) next to the re-
spective function/parameter.
Editing a text
The following table shows the letters (small and capital)
and punctuation marks provided by the keys. To edit a
text, press the respective until the required character is
shown.
1
2
a
4
g
6
m
8
t
0
Use D to move along the display lines.
Use D or C to scroll the text: the selected character will
blink.
Use 0 or 1 for spaces between letters.
KEYPAD OPERATIONS
1
!
.
;
#
$
%
'
b
c
A
B
C
2
3
d
h
i
G
H
I
4
5
j
n
o
M
N
O
6
7
p
u
v
T
U
V
8
9
w
0
+
-
*
/
=
:
;
"
(
)
[
]
{
}
e
f
D
E
F
3
k
l
J
K
L
5
q
r
s
P
Q
R
S
7
x
y
z
W
X
Y
Z
9
<
>
?
&
@
^
|
5
Advertisement
Chapters
Table of Contents
