Quick View Trouble Mode (Enter); Partition Status Enquiry; Accessing The User Menu (<Codeenter); Arm/Disarm - Bentel Security KYO 320 Installation Manual

Bypassed Zones!
____Arm?___
If this condition is present:
Ø press B to view the Bypassed zones.
Ensure that no zones have been bypassed (turned
OFF) unintentionally. If necessary, use the ON key to
UnBypass (turn ON) Bypassed zones.
Press ENTER to Arm the Partitions.
+
All zones must be unbypassed before Arming the
Partitions otherwise security will be greatly reduced.
In the following example, zone 5 has been BYPASSED.
Zone 005
STBY BYPASSED
+
Use A or B to scroll the zones in Alarm, Inactive or
Bypassed status.
n Quick View Trouble Mode (ENTER)
Your system will continuously check for Trouble condi-
tions. If a Trouble condition occurs, the Amber G LED
on the Keypad will turn ON.
To check current Troubles (from standby):
Press the ENTER key on the Keypad.
(If the Compatibility with EN50131 option has been set,
it will be necessary to set the user code followed by the
ENTER button, then press the ENTER button a second
time).
If several Trouble conditions are present:
Use A or B to scroll the list (Table 5 shows the various
Trouble conditions).
Current trouble:
Loss of clock
If you access the View Trouble Mode and no Trouble
conditions are present, the display will show the follo-
wing message:
Current trouble:
none!
Press the ENTER key to exit.
n Partition status enquiry
Press the ON key to view the status of the Keypad Parti-
tions:
DD-I-PZ--DDDDII
---IIIPZZ--DI---
The first line of the display will show (from right to left)
the status of Partitions no. 1 through no. 16, the second
row of the display will show (from left to right) the status
of Partitions no. 17 through no. 32. The hyphen (–) indi-
cates that the Partition is not a Keypad Partition.
The Partition status will be shown for approximately 6
seconds.
KYO320
âå
OPERATING YOUR SYSTEM FROM A KEYPAD
+
Partition status enquiry is possible on Enabled
Keypads only. If Partition Alarm or Tamper is pre-
sent the respective character will blink.
+
"View Trouble" mode provides information regar-
ding zones which generate "Low Battery WLS" and
"WLS Device lost" events. For the event details
(i.e. iinformation regarding the zone concerned),
press D.
Accessing the User menu (<CodeENTER)
(for PREMIUM LCD and CLASSIKA LCd Keypads)
Enter a valid User Code then press the ENTER key to
access the User menu. The User menu will allow Users
to access ONLY the commands they are enabled for.
+
You can access the User menu when the Control
panel is Armed or Disarmed.
+
(If the Compatibility with EN50131 option has been
set, it will first be necessary to enter the code for
View control unit status mode, then press ENTER
to access the User menu).
Using A and B, scroll for the required option then press
the ENTER key.
Press ESC as many times as required to step back and
exit the menu.
+
Several Users can access the menu at the same
time from different keypads.
The User menu provides the following options:
r Reset Alarms
r Stop Alarms
r Arm/Disarm
r Overtime request
r Overtime request
r Enable/Disable auto-arm
r Enable/Disable Teleservice
r Enable/Disable Answering device
r Disable buzzer
r Change Telephone number
r Program PINs
r Change Time and Date
r Reset PC Programming
r Test Keypad
r Test Siren
r Activate Outputs
r Zone status
r Continuous recording
r Memo
r Event logger
r Clear call queue
r Enable/Disable Timers
r Enable/Disable Key
9