Superkey Functions; Audible And Visual Signals On The Keypad; Leds; Display - Bentel Security KYO 320 Installation Manual

brightness after 10 seconds of inactivity).
To adjust the brightness of the LCD display, press and
hold:
Ø A to increase brightness
Ø B to decrease brightness
Press OFF to set the stand by brightness.
ON and OFF alternate, respectively, the settings for the
normal and the stand by status level.
To confirm the selected levels, press ENTER (or simply
wait a few seconds to enable the keypad back into the
stand by status).
+
If the brightness in the "stand-by status" is set to a mi-
nimum, the keypad LEDs go out except in an alarm or
fault condition (see Manual of keypads).

Superkey functions

If your Installer has set up the 'Superkeys', you will be
able to perform some "Quick" operations from the key-
pad without using codes. The table shows how to acti-
vate the programmed functions.
PREMIUM LCD
CLASSIKA LCD
Press and hold the key for
1
approximately 3 seconds
Press and hold the key for
2
approximately 3 seconds
Press and hold the key for
3
approximately 3 seconds
The 'Superkeys' can be set up to activate:
Ø Electrical appliances (e.g. Heating system, Lights,
etc.)
Ø the Digital communicator
Ø the Dialler
The 'Superkey' actions are instant and will be confir-
med by a feed back signal (beep).
Symbol
Off: all the keypad Partitions are Disarmed
On: at least one of the keypad Partitions is Armed
I
Slow blinking: STOP ALARMS function -activated by keypad- is Active
Fast blinking
NOTE - With EN50131 keypad, the indicator light is always off: to display the various
functions listed above, you will have to enter the "View zone status" mode.
Off: Standby status -NO alarms-
On: Zone Alarms in memory
a
Slow blinking: Tamper on at least one zone or on thr Control panel
Fast blinking: Alarm and Tamper on at least one zone, or Tamper on the Control panel
Off: No trouble conditions detected
G On: At least one Trouble condition detected
Slow blinking: At least one zone in Test status
Fast blinking: At least one zone in Test status and one in Trouble status
Off: No voice messages in memory
M
On: At least one voice message in memory
Note: The zone Alarm and Tamper events, signalled on the LEDs, refer to zones which belong to the
keypad Partitions.
KYO320
Activation method
TABLE 1 - KEYPAD LEDs
: STOP ALARMS function is Active and AT LEAST ONE of the keypad
Partition is Armed
.
OPERATING YOUR SYSTEM FROM A KEYPAD
The Superkeys can be set up to work differently on
different Keypads.

Audible and Visual signals on the Keypad

Table 1 shows the meaning of the indicator LEDs on the
PREMIUM LCD and CLASSIKA LCD Keypads.
+
Some of the display screens differ, depending on
whether the keypad has been set with the option
"Compatibility with EN50131" or not.
n LEDs
Refer to Table 1 for the description of the four LEDs on
the Keypad.
n Display
During standby status, the first line will show the Time
and Date, as follows.
17:05 26/08/06
AAADDDDD x ** ÿ
1 2 3 4 5 6 7 8 S T b f s t r i
If the keypad has been set in EN50131 mode, the
standby display screen will be similar to the one show
below:
17:05 26/08/06
Enter PIN
+
The text "Enter PIN" can be programmed by the in-
staller.
If the Control panel has stored a zone Alarm or Tamper
event (a LED on or blinking, respectively), the first line will
show the description of the zone concerned, as follows.
Meaning
5