Arming Partitions; (<Code> On); Disarming Partitions; (<Code> Off) - Bentel Security Kyo 320 User Manual

The User can enter the following commands at the
Keypad.
n Arming Partitions
This command will Arm all the common Partitions of the
User code and the Keypad concerned.
+
DO NOT assign Duress Codes to Arming com-
mands.
n Disarming Partitions
This command will Disarm all the common Partitions of
the User code and the Keypad concerned.
Disarm under Duress
This command requires entry of a Duress Code. The
Control panel will Disarm the Partitions and will send
the programmed Alarm calls but will not signal the out-
going calls on the Keypad (usually signalled by a ÿ over
the i icon).
Disarm by Patrol Code
If a Patrol Code is used to Disarm the Partitions, the
Control panel will rearm the Partitions automatically
when the programmed Patrol Time expires.
n Arming in A, B, C or D Mode
(<Code> A, B, C or D)
+
DO NOT assign Duress Codes to A, B, C or D
Mode Arming commands.
Each user code can be set up to manage four different
Arming mode configurations: A, B, C and D. These con-
figurations determine the Partitions that will Arm, and
those that will Disarm when an A, B, C or D Mode com-
mand is entered at a Keypad (the final configuration de-
pends on the User code and Keypad Partitions).
+
Keypads can operate ONLY on the Partitions they
are assigned to.
n Quick Arming for PREMIUM LCD and CLASSIKA

LCD keypad

1. Press ON: the Keypad will sound a beep.
2. Press and hold the ON key for approximately 3 se-
conds, the Keypad will sound a second beep, and the
display will show the following message:
Quick_arming ___
Type:_A,B,C,D__
3. Press A, B, C or D within 4 seconds (to Arm in A, B, C
or D mode, as required). If you do not press a key within
4 seconds the Control panel will Arm the Partitions au-
tomatically in Away mode.
Quick Arm operations will affect the Keypad Partitions
and the Partitions assigned to the Quick Arm method.
8
(<Code> ON)
(<Code> OFF)
+
Your Installer will tell you which Keypads can be
used, and which Partitions are involved.
You can Arm/Disarm the Partitions separately using a
6-digit User Code PIN, as follows: — type in a 6-digit
User Code PIN followed by the 2-digit ID number of the
Partition concerned , then press ON, OFF, A, B, C or D,
as required. The partition concerned will Arm/Disarm in
accordance with programming.
Example: If the 6-digit User code PIN is 135790, and
you want to Arm Partition 13 in Away Mode, type-in
13579013 then press ON. If you want to Disarm Parti-
tion 13, using the same PIN, type-in 13579013 then
press OFF. If you enter 13579013 then press A, B, C or
D, Partition 13 will Arm in accordance with the respecti-
ve configuration.
n About Partition Arming
If you Arm a Partition with an Exit Time, the Keypad will
emit slow beeps to signal the elapsing Exit Time.
If you arm several Partitions with different Exit Times,
the Keypad will emit slow beeps until all the Partition
Exit Times expire. However, each Partition will Arm
when its own Exit Time ends.
When you enter a valid Arming command at a Keypad,
the Control panel will check for:
a) Zones in Alarm
b) Inactive Zones
c) Bypassed Zones
d) WLS delinquency zone
The Partitions will Arm instantly if none of these conditions
is present. If the system detects zones in Alarm, Inactive
and/or Bypassed and/or WLS delinquency status, the re-
spective message will be shown on the display.
Open Zones!
Arm? âå
Open Zones!
View byp.Zones?â
+
The second message only appears if the "Disable
activation with alarmed areas" option has been se-
lected.
If this condition is present:
Ø press B then, scroll for the zones concerned.
Ensure that all the zone doors and windows are clo-
sed securely, and that there is no motion in the vici-
nity of motion detectors;
Øpress ESC to abort the command, then retry.
+
All zone Alarms must be cleared before Arming the
Partitions otherwise Arming will generate an Alarm.
Inactivity!
Arm ? âå
If this condition is present:
Ø press B to view the Inactive zones.
Ø press ESC to abort the command, then retry.
KYO320