Code Types; User Code Types - Bentel Security KYO 320 Installation Manual

WLS Key n.
Wireless Key 001
5a. Using A or B, select the wireless key to be program-
med, then press ENTER.
Description
Wireless key 001
6a. Enter the respective label (refer to "Entering a text"
under "Using the Keypad"), then press ENTER.
Partition
XXXXXXXX
7a. Enable the Wireless Key on the relevant Partitions
(refer to "Enabling Partitions and under "Using the Key-
pad"), then press ENTER.
Yel. arm. 1-8
AAAAAAAA
8a. Set up the Yellow Mode configuration for the Wire-
less Key concerned (D: Disarm, N: None, A: Arm, S:
Arm in Stay mode, I: Istant mode, then press ENTER.
Green arm. 1-8
DDDDDDDD
9a. Set up the Green Mode configuration for the Wire-
less Key concerned (D: Disarm, N: None, A: Arm, S:
Arm in Stay mode, I: Istant mode), then press ENTER
to go back to step 5a.

Code Types

From the Programming menu:
PROGRAMMING
Configuration
1. Using A or B, select the Code types option.
PROGRAMMING
Code types
2. Press ENTER:
Code type n. 001
User type
3. Using A or B, select the Code type, then press
ENTER.
Description
User type 001
4. Enter the label (Description) (refer to "Entering a
Text") of the selected Code type, then press ENTER.
28
001
1-8
001
+
NOTE: If, at step 3 (User type), you select a User
type (codes 1 through 16) go
Types". If you select an Installer type (codes 17,
18 and 19) go to "Installer Code Types".
n User Code Types
Option section 1
Reset Alarm
5.Using A or B, select the functions from Option sec-
tion 1: Reset Alarms (refer to "Panel reset"), Stop
Alarms (refer to" Stop Alarm"), Arm/Disarm (refer to
"Arm./Dis. from User menu"), Overtime Request (refer
to "Request overtime"), Teleservice Req (refer to "Re-
quest teleservice"), En./Dis. autoar (refer to "Enab./Di-
sab. scheduler"), En./Dis.
"Enab./Disab. teleservice"), En./Dis.Ans.Dev (refer to
"Enab./Disab. answering machine"). Press ON or OFF,
respectively, to enable or disable the function concer-
ned ("û" means enabled, and "-" means disabled).
Press ENTER to go to the next Option section.
Option section 2
Disable buzzer x
6. Using A or B, select the functions from Option sec-
tion 2: Disable buzzer (refer to "Enab./Disab. keypad
buzzer"), Change tel. num (refer to "Phone number
modify"), Change time/date (refer to "Date/time mo-
dify"), Reset PC Prog. (refer to "Reset warning PC
progr."), Test keypad (refer to "Keypad test"), Test si-
ren (refer to "Squawk"), Activate output (refer to "Out-
put On/Off"). Press ON or OFF, respectively, to enable
or disable the function concerned ("û" means enabled,
and "-" means disabled). Press ENTER to go to the
next Option section.
Option section 3
Zone Status
7. Using A or B, select the functions from Option sec-
tion 3: Zone status (refer to "Bypass/Unbypass zo-
nes"), Continuous rec. (refer to "Reset/play/restart
continuous rec."), Home message (refer to "Play/Reg.
memo"), Event Logger (refer to "View logger"), Clear
call queue (refer to "Clear Call Queue"), En./Dis. ti-
mers (refer to "Enable Timers Control"). En./Dis. Keys
(refer to "Enable Key Control"). Using ON or OFF, re-
spectively, enable or disable the function concerned
("û" means enabled, "-" means disabled). Press
ENTER to go to the next Option section.
Option section 4
No tel.part.S/Rx
8. Using A or B, select the functions from Option sec-
tion 4: No tel.part.S/R (refer to "Clear phone queue on
partition in stop/reset"), No tel.pan. S/R (refer to "Clear
phone queue on panel in stop/reset"), No tel. disarm
(refer to "Clear phone queue on disarming"), Reset
part.al. (refer to "Reset Partition Alarms"), Stop
to "User Code
x
Teleser (refer
x
KYO320
to