INIM Electronics Prime Programming Manual page 54

This value determines the number of rings the system
Number of rings
allows before picking up an incoming call (from 1 to
for answerphone
15).
This value determines the reception sensitivity of
incoming call rings.
Ring sensitivity
At default this value is set at 60. Accepted values: 1 to
120.
If several voice calls (digital or SIA-IP) generated by
Call all voice/
the an event are waiting in the outgoing call queue,
digital/SIA-IP
the control panel will attempt to send voice calls to all
numbers
the numbers of this type.
Allows access to the User Menu over-the-phone
Access DTMF (during voice calls from the control panel) in
menu without accordance with the access level (enabled options,
code etc.) of the last user code that operated on the control
panel (code 30, 50 or 100).
Start message The control panel will start the voice message 5
after dialing seconds after dialing the respective contact number.
The control panel will consider the voice call successful
Confirm call with
when the recipient presses the "*" key on the
"*"
telephone keypad.
UTC Time on Calls to SIA-IP type numbers will contain the date and
SIA-IP time in "UTC" format (Coordinated Universal Time).
Increase DTMF Option that increase the sensitivity of incoming DTMF
sensitivity tones.
No SIA strings
The descriptive strings will not be sent in SIA/SIA-IP
No SIA-IP
protocol.
strings
Partition arming events using CONTACT-ID protocol
Arm/Disarm will send the "New event/Event activation" code when
inverted on C.ID the partition arms, and the "Event ended/Event
restore" code when the partition disarms.
If this option is enabled, it blocks all the calls
Generates one
programmed for an event after the first successful
call only for each
call. If the options "Call all voice/digital/SIA-IP
event
numbers" are enables, then the latter have priority.
Stop calls on dis- The control panel will not carry out the calls
arm with no programmed for disarm events when there is no active
alarms alarm or alarm memory present.
Number of voice
This value determines the number of times the voice
mess. repeti-
message will be played during the call (from 1 to 15).
tions
This value determines the number of calls attempts
Number of
the system will make before deleting the contact
attempts
number from the call queue (from 1 to 15).
This parameter allows you to program the delay,
Delay on line-
expressed in seconds or minutes, which will be applied
down signal
before "Line Down" events is signalled.
Telephone num-
ber 15 reserved For future use
for teleservice
Installer call-
For future use
back
Programming field for the setting, expressed in
SIA-IP polling
seconds, of the between two consecutive polling
interval
signals.
Option that disables the polling function for all
Disabled
telephone numbers.
11-2-1
54
Table 11-2: Telephone parameters
Telephone line adjustment
The "Outgoing voice volume" and "Incoming voice volume" parameters can be used to correct
the voice functions of the dialer and DTMF tones (refer to Table 4-3: Control panel options).
The values of these parameters affect each other, therefore, and a good result is always a
compromise.
If you are not using a GSM interface, you should:
• Adjust one parameter at a time and carry out tests to verify the result.
• Increase/decrease the values in small steps (for example, from 25 to 22 and not from 25
to 15).
Centrali anti-intrusione
Telephone
Number of rings
Other parameters,
Ring sensitivity
Telephone
Parameters
parameters,
Call allVoxNums
Telephone dialer
parameters
Call all TLVNums
Call all SIA-IP
DTMF withoutCode
BypassVoiceCheck
Confirm with *
UTC timeOnSIA-IP
DTMF sensitivity
NoStrings SiaProt
NoStrings SIA-IP
CONT-IDInversion
SingleCallEachEv
Disab.Tel.Disarm
Telephone
Message repeats
Max.num.attempts
Other parameters,
LinedownDelay
Telephone
Parameters
parameters,
Num15 ForTeleserv
Teleservice
parameters
Install.callback
Telephone
parameters
Not available
Programming the telephone