INIM Electronics Prime Programming Manual page 13

Programming manual
if this option is enabled and the selected shortcut
involves a scenario that disarms a partition, or
Code entry in the
switches a partition from Away mode to Stay mode,
event of secu-
the security of your system will obviously be at risk,
rity risk
therefore, the system will request entry of a valid
code.
If this option is enabled when the user selects the
shortcut via the relative function key, the system will
request confirmation before actually activating the
Requires confirm
shortcut, confirmation is achieved by simply pressing
operation
the key. This option helps the user avoid accidental
activations.
This option is not available for Alien keypads.
Enter the value of the hysteresis for the "Air
conditioning" function of the selected keypad (if
Temperature
enabled).
hysteresis
The entered value must be expressed in °C decimals
(from a minimum of 0 to a maximum of 4).
If this option is enabled, the room temperature will
Disable tem-
not be flashed on the display. This option is valid only
perature reading
for keypads equipped with thermometers.
Disable entry- This option enables/disables the buzzer during
partition entry-time
time signal
Disable audible
This option enables/disables the buzzer during
partition exit-time
exit-time signal
Audio signal on
This option enables/disables the buzzer when
terminal T1 out-
terminal T1 on the keypad is activated as an output.
put
This option enables/disables the buzzer that signals
Disable chime
the violation of the bell zone of the keypad.
LED OFF in If enabled, in the event of inactivity on the keypad for
at least 40 seconds, the respective LEDs will go off.
stand-by
Bypass wireless
If enabled, this option will inhibit control panel
supervision of the wireless keypad.
supervision
If enabled, this option will inhibit wireless keypad
Bypass tamper
tamper signalling on the control panel.
Section for the selection of the outputs for home
Domotic Out-
automation, that can be activated without a valid
code (see paragraph 6-2-1 Outputs activatable
puts enabling
without authentication).
Thermostat on
This key directly accesses the programming section of
keypad the "Thermostat ON" event
Valid code at
This key directly accesses the programming section of
the "Valid code at keypad" event
keypad
This parameter allows you to enter the effective value
of the room temperature read by an external
thermometer. This value will replace the keypad
temperature reading and thus allow you to correct
Temperature the temperature sensor on the keypad you are
working on (valid for keypads with temperature
adjustment
sensors only).
The entered value must be expressed in °C decimals
(for example, type in 252 if the temperature is 25.2
°C).
The "Listen-in" and "Arming status" shortcuts will have no effect if requested at a keypad.
If you are programming an Alien keypad, the only type of shortcut that functions is "Arm/disarm".
The process of programming the graphic interface and maps on the Alien keypad must be
done through the Prime/STUDIO software program.
Once you have selected the keypad you must select "Touch keypad" as its type. The "General"
section, which is the same for all keypad types, appears with the following sections:
• "Alien graphics", for the graphic interface setup (backgrounds, buttons, icons)
• "Alien maps", for the configuration of the graphic maps which are accessed through the
"Maps" option in the APPs" section Chapter 20 Graphic map configuration.
Programming peripherals
Table 3-2: Parameters for single keypads
Configured keypads ,
selected keypad
Not available
SecurityRiskCode
Confirm
Keypads, ChoosePeriph-
eral, "keypad"
Keypads, ChoosePeriph-
eral, "keypad", Op-
tions,
Temperature off
NoEntryTimeSign.
NoExitTimeSignal
Beep on output
Disable Chime
LED OFF in standby
NO Superv. WLS
Disable tamp. WLS
Not available
Events, Thermostat ON
Events, Valid Code
Other parameters, Temp.
adjustment
Note
TOUCH-SCREEN
KEYPADS
13