Mitsubishi Electric FR-F800 Series Instruction Manual page 648

For
indication
on external
meters
Operation
panel (FR-
DU08)
Protective
function
Surrounding air temperature
Surrounding air humidity
Storage temperature
Ambience
Altitude/vibration
*1 The function is available for standard structure models and IP55 compatible models.
*2 Not activated in the inverter in the initial state.
*3 Available only for the IP55 compatible model.
*4 Applicable to conditions for a short time, for example, in transit.
*5 2.9 m/s
Downloaded from ManualsNet.com
Pulse train Max. 2.4 kHz via one terminal (for the indication of inverter output frequency).
output (FM
The item for monitoring can be changed using Pr.54 FM/CA terminal function selection.
type inverter)
Current output Max. 20 mADC via one terminal (for the indication of inverter output frequency).
(CA type
The item for monitoring can be changed using Pr.54 FM/CA terminal function selection.
inverter)
Max. 10 VDC via one terminal (for the indication of inverter output frequency).
Voltage output
The item for monitoring can be changed using Pr.158 AM terminal function selection.
Output frequency, output current, output voltage, and frequency setting value are monitored.
Status
monitoring
The item for monitoring can be changed using Pr.52 Operation panel main monitor selection.
When a protective function is activated, a fault indication is displayed and the output voltage, output
Fault type current, output frequency, cumulative energization time, date (year, month, day) and time at the
occurrence of the fault are stored. Each fault is recorded and the last 8 records can be displayed.
Overcurrent trip during acceleration, Overcurrent trip during constant speed, Overcurrent trip during
deceleration or stop, Regenerative overvoltage trip during acceleration, Regenerative overvoltage trip
during constant speed, Regenerative overvoltage trip during deceleration or stop, Inverter overload
trip (electronic thermal relay function), Motor overload trip (electronic thermal relay function), Heat
sink overheat, Instantaneous power failure
stop, Loss of synchronism detection
side earth (ground) fault overcurrent, Output short circuit, Output phase loss, External thermal relay
Fault
*2
operation , PTC thermistor operation
device fault (control circuit board), PU disconnection, Retry count excess
panel power supply short circuit/RS-485 terminals power supply short circuit, 24 VDC power fault,
Abnormal output current detection
Analog input fault, USB communication fault, Safety circuit fault, Overspeed occurrence
fault, Pre-charge fault, PID signal fault
Abnormal internal temperature
Fan alarm, Stall prevention (overcurrent), Stall prevention (overvoltage), Electronic thermal relay
function pre-alarm, PU stop, Parameter copy, Safety stop, Maintenance signal output
Alarm,
Warning, Error error, Operation panel lock
message
external power supply operation, Load fault warning, Emergency drive in operation
operation during communication fault
-10°C to +50°C (non-freezing) (LD rating)
-10°C to +40°C (non-freezing) (SLD rating, IP55 compatible models)
95% RH or less (non-condensing) (With circuit board coating (conforming to class 3C2/3S2 in IEC
60721-3-3:1994), IP55 compatible models).
90% RH or less (non-condensing) (Without circuit board coating).
*4
-20°C to +65°C
Indoors (free from corrosive gas, flammable gas, oil mist, dust and dirt)
2500 m or less (For the installation at an altitude above 1000 m, consider a 3% reduction in the rated
current per 500 m increase in altitude.) 5.9 m/s
2
or less for the FR-F840-04320(185K) or higher.
search engine
*1
, Undervoltage
*2
, Upper limit fault detection, Lower limit fault detection, Output
*2
, Option fault, Communication option fault, Parameter storage
*2
, Inrush current limit circuit fault
*2
, Internal circuit fault, User definition error by the PLC function,
*3
, Internal storage device fault
*2 *2
, Password locked , Parameter write error, Copy operation error, 24 V
*2 *3
, Internal fan alarm
2 *5
or less at 10 to 55 Hz (directions of X, Y, Z axes)
*1 *1*2
, Input phase loss , Stall prevention
*2
, CPU fault, Operation
*1
, Communication fault (inverter),
*2
, 4 mA input
*2
, USB host
*1
, Continuous
8. SPECIFICATIONS
8.3 Common specifications
1
2
3
4
5
6
7
8
9
10
647