Figure 4-13
Conveyor I/O (Outputs 0-31) ............................................................................................4-19
Figure 4-14
Conveyor I/O (Inputs 0-31) ...............................................................................................4-20
Figure 4-15
Setup Conveyors ..............................................................................................................4-23
Figure 4-16
Dispenser I/O (Outputs 0-31) ...........................................................................................4-24
Figure 4-17
FmXP Jog Window ...........................................................................................................4-25
Figure 4-18
Vision and Reticles Set-up Dialog Boxes .........................................................................4-27
Figure 4-19
Machine Offsets Parameters Dialog Box..........................................................................4-30
Figure 4-20
Dispenser I/O (Inputs 0-31) ..............................................................................................4-31
Figure 4-21
Dispenser I/O Test (Outputs 32-63) .................................................................................4-32
Figure 4-22
Service Station..................................................................................................................4-33
Figure 4-23
Scale Setup ......................................................................................................................4-34
Figure 4-24
Heater Control Window ....................................................................................................4-36
Figure 4-25
Valve Offset Dialog Boxes................................................................................................4-39
Figure 4-26
Machine Setup Dialog Box ...............................................................................................4-40
Figure 4-27
Program Open Window ....................................................................................................4-41
Figure 4-28
Run Window .....................................................................................................................4-41
Figure 5-1
Focusing the Camera ......................................................................................................... 5-2
Figure 5-2
FmXP Setup Vision............................................................................................................. 5-3
Figure 5-3
FmXP Calibration Window.................................................................................................. 5-4
Figure 5-4
Adjusting the Service Station Height .................................................................................. 5-5
Figure 5-5
Scale Cover Removal ......................................................................................................... 5-6
Figure 5-6
Leveling the Scale .............................................................................................................. 5-6
Figure 5-7
Setup Scale - Scale Operations Tab ..................................................................................5-7
Figure 5-8
Setup Scale - Advanced Tab.............................................................................................. 5-7
Figure 5-9
FmXP Calibrating Scale Message......................................................................................5-8
Figure 5-10
FmXP Calibration Complete Message ............................................................................... 5-8
Figure 5-11
Z-head Counter Balance Force Adjustment ....................................................................... 5-9
Figure 5-12
Adjusting the Height Sensor Probe ..................................................................................5-10
Figure 5-13
Board Sensor - Side View ................................................................................................5-11
Figure 5-14
Board Sensor - Top View .................................................................................................5-11
Figure 5-15
Initializing the Digital Gauge .............................................................................................5-13
Figure 5-16
Beacon Configuration Dialog Box.....................................................................................5-14
Figure 5-17
Beacon Configuration Dialog Box.....................................................................................5-15
Figure 5-18
Dispenser I/O Dialog Box .................................................................................................5-15
Figure 6-1
Valve Pneumatic and Electrical Connections (DV-8000 shown)........................................ 6-2
Figure 6-2
Valve Pneumatic and Electrical Connections (DJ-9000 shown) ........................................ 6-3
Figure 6-3
Main Air Pressure Regulator and Gauge Sets ................................................................... 6-4
Figure 6-4
Adjusting the Valve and Fluid Pressure Regulators ........................................................... 6-5
Figure 6-5
Low Air Pressure Detection Window .................................................................................. 6-6
Figure 6-6
Setup Valve Offsets Dialog Box ......................................................................................... 6-7
Figure 6-7
FmXP Error Message 30694 .............................................................................................. 6-8
Figure 6-8
Production Window - Teaching Safe Z Height ................................................................... 6-9
Figure 6-9
Teaching Safe Z Height...................................................................................................... 6-9
Figure 6-10
Conveyor Position Controls ..............................................................................................6-10
Figure 6-11
Dispensing Head Position Controls ..................................................................................6-12
Figure 6-12
Conveyor Position Controls ..............................................................................................6-15
Figure 6-13
Camera LED's (Rear View) ..............................................................................................6-16
Figure 6-14
Camera Lighting Adjustment ............................................................................................6-18
Figure 6-15
Fluidmove Production Window .........................................................................................6-20
Figure 6-16
Heater Control Window ....................................................................................................6-21
Figure 6-17
FmXP Fluid Manager........................................................................................................6-22
Figure 6-18
Workpiece Alignment Options ..........................................................................................6-23
Figure 6-19
Create Workpiece .............................................................................................................6-24
Figure 6-20
Machine Setup Window....................................................................................................6-25
Figure 6-21
Programming Window ......................................................................................................6-26
Figure 6-22
Program Commands Toolbar ...........................................................................................6-27
xii
Table of Contents
Need help?
Do you have a question about the Asymtek Spectrum Series and is the answer not in the manual?