Comtech EF Data LPOD PS 1.5 Installation And Operation Manual page 160

LPOD C-, X-, or Ku-Band Outdoor Amplifier / Block Up Converter (BUC)
Serial Interface Operation
Controller-to-Target
Instruction Code and
Parameter Type
Qualifier
(* indicates
End-of-Life)
Command Query
SNMP Read SRC= SRC?
Community
SNMP System SSC= SSC?
Contact
Set Statistics SSI= SSI?
Interval
SNMP System SSL= SSL?
Location
SNMP Unit Name SSN= SSN?
SNMP Trap STA= STA?
Destination IP
Address 1
SNMP Trap STB= STB?
Destination IP
Address 2
SNMP Trap STV= STV?
Version
SNMP Write SWC= SWC?
Community
Arguments for
Command or
Query
16 bytes, Command or Query.
characters, no Sets or returns the SNMP Read Community string.
spaces NOTE: An empty string is not allowed.
COMMAND EXAMPLE: <0001/SRC=public{CR}
255 bytes, Command or Query.
characters, Sets or returns the SNMP System Contact string.
COMMAND EXAMPLE: <0001/SSC=Joe Net Admin{CR}
NOTE: When not configured, the Target returns an empty string: <0001/SSC={CR}{LF}
2 bytes Command or Query.
Sets or returns the time interval, in minutes, at which statistics are logged in the form xx, where:
xx=interval, from 01 to 99 minutes (SEE NOTE)
Default value: 90 minutes.
COMMAND EXAMPLE: <0001/SSI=90{CR}
255 bytes, Command or Query.
characters Sets or returns the SNMP System Location string.
COMMAND EXAMPLE: <0001/SSL=Upstairs back right.
NOTE: When not configured, the Target returns an empty string. <0001/SSL={CR}{LF}
16 bytes, Command or Query.
characters Sets or returns the SNMP Unit Name string.
COMMAND EXAMPLE: <0001/SSN=Remote1{CR}
NOTE: When not configured, the Target returns an empty string. <0001/SSC={CR}{LF}
15 bytes, Command or Query.
Numerical Sets or returns the IP Address of the SNMP Trap Destination IP Address 1 (where
traps will be sent first) in the form xxx.xxx.xxx.xxx, where:
xxx.xxx.xxx.xxx=IP Address
COMMAND EXAMPLE: <0001/STA=010.006.030.001{CR}
NOTE: When not configured, the Target returns >0001/STA=0.0.0.0{CR}{LF}
15 bytes, Command or Query.
Numerical Sets or returns the IP Address of the SNMP Trap Destination IP Address 2 in the form xxx.xxx.xxx.xxx, where:
xxx.xxx.xxx.xxx=IP Address
COMMAND EXAMPLE: <0001/STB=010.006.030.002{CR}
NOTE: When not configured, the Target returns >0001/STB=0.0.0.0{CR}{LF}
1 byte Command or Query.
Sets or returns the SNMP Trap Version that will be used to send traps in the form x, where:
1=SNMP Trap Version 1
2=SNMP Trap Version 2
COMMAND EXAMPLE: <0001/STV=0{CR}
16 bytes, Command or Query.
characters, no Sets or returns the SNMP Write Community string.
spaces COMMAND EXAMPLE: <0001/SWC=private{CR}
NOTE: An empty string is not allowed.
Description of Arguments
(Note that all arguments are ASCII numeric codes from 48 to 57)
5–30
MN-LPOD
Revision 14
Target-to-Controller
(see Description of Arguments)
Response to Response to
Command Query
SRC = SRC=x
SRC!
SSC = SSC=x [1..128]
SSC!
SSI= SSI=xx
SSI?
SSL = SSL=x[1..128]
SSL!
SSN = SSN=x[1..128]
SSN!
STA = STA=xxx.xxx.xx
STA! x.xxx
STB = STB=xxx.xxx.xxx
STB! .xxx
STV = STV=x
STV!
SWC = SWC=x
SWC!