Siemens SINUMERIK 840D sl Operating Manual page 13
Milling
Hide thumbs
Also See for SINUMERIK 840D sl:
- Function manual (2184 pages) ,
- Programming manual (1334 pages) ,
- Commissioning manual (1102 pages)
Table of Contents
Advertisement
8.3.10
Milling contour pocket (CYCLE63).............................................................................................403
8.3.11
Residual material contour pocket (CYCLE63) ...........................................................................406
8.3.12
Milling contour spigot (CYCLE63)..............................................................................................408
8.3.13
Residual material contour spigot (CYCLE63) ............................................................................410
8.4
Turning - only for G code programs...........................................................................................412
8.4.1
General ......................................................................................................................................412
8.4.2
Stock removal (CYCLE951).......................................................................................................412
8.4.2.1
Function .....................................................................................................................................412
8.4.3
Groove (CYCLE930)..................................................................................................................417
8.4.3.1
Function .....................................................................................................................................417
8.4.4
Undercut form E and F (CYCLE940) .........................................................................................422
8.4.4.1
Function .....................................................................................................................................422
8.4.5
Thread undercut (CYCLE940) ...................................................................................................426
8.4.5.1
Function .....................................................................................................................................426
8.4.6
Thread turning (CYCLE99) ........................................................................................................429
8.4.6.1
Function .....................................................................................................................................429
8.4.7
Thread chain (CYCLE98)...........................................................................................................438
8.4.7.1
Function .....................................................................................................................................438
8.4.8
Cut-off (CYCLE92).....................................................................................................................441
8.5
Contour turning- only for G code programs ...............................................................................443
8.5.1
General information ...................................................................................................................443
8.5.2
Representation of the contour....................................................................................................444
8.5.3
Creating a new contour..............................................................................................................445
8.5.4
Creating contour elements.........................................................................................................447
8.5.5
Changing the contour.................................................................................................................453
8.5.6
Contour call (CYCLE62) ............................................................................................................454
8.5.6.1
Function .....................................................................................................................................454
8.5.7
Stock removal (CYCLE952).......................................................................................................455
8.5.7.1
Function .....................................................................................................................................455
8.5.8
Stock removal residual (CYCLE952) .........................................................................................461
8.5.8.1
Function .....................................................................................................................................461
8.5.9
Grooving (CYCLE952) ...............................................................................................................464
8.5.9.1
Function .....................................................................................................................................464
8.5.10
Grooving residual material (CYCLE952) ...................................................................................467
8.5.11
Plunge turning (CYCLE952) ......................................................................................................469
8.5.12
Plunge turning residual material (CYCLE952)...........................................................................472
8.6
Further cycles and functions ......................................................................................................475
8.6.1
Swivel plane/tool (CYCLE800)...................................................................................................475
8.6.2
Swiveling tool (CYCLE800)........................................................................................................485
8.6.2.1
Swiveling tool/preloading milling tools - only for G code program (CYCLE800) .......................485
8.6.2.2
Swiveling aligning tool - only for G code program (CYCLE800)................................................487
8.6.3
High-speed settings (CYCLE832)..............................................................................................488
8.6.4
Subroutines ................................................................................................................................491
8.7
Additional cycles and functions in ShopMill ...............................................................................493
8.7.1
Transformations .........................................................................................................................493
8.7.2
Translation .................................................................................................................................494
8.7.3
Rotation......................................................................................................................................495
8.7.4
Scaling .......................................................................................................................................496
8.7.5
Mirroring .....................................................................................................................................497
8.7.6
Cylinder surface transformation .................................................................................................498
Milling
Operating Manual, 03/2013, 6FC5398-7CP40-3BA1
Table of contents
13
Advertisement
Table of Contents
