S: Elevator Parameters - YASKAWA L1000V Technical Manual

B.3 Parameter Table
No. (Addr.) Name
o4-11
U2, U3 Initialization
(510H)
o4-12
kWh Monitor Initialization
(512H)
o4-13
Number of Travels Counter Reset
(528H)
u S: Elevator Parameters
This section describes various functions and faults needed to operate an elevator application: braking sequence, slip
compensation for elevators, start/stop optimization, Rescue Operation, and elevator-related faults.
n
S1: Brake Sequence
No. (Addr.) Name
S1-01
Zero Speed Level at Stop
(680H)
S1-02
DC Injection Current at Start
(681H)
S1-03
DC Injection Current at Stop
(682H)
S1-04 DC Injection/Position Lock Time
(683H) at Start
S1-05 DC Injection/Position Lock Time
(684H) at Stop
S1-06
Brake Release Delay Time
(685H)
S1-07
Brake Close Delay Time
(686H)
S1-10
Run Command Delay Time
(687H)
S1-11 Output Contactor Open Delay
(688H) Time
<5> Default setting is determined by the control mode (A1-02).
n
S2: Slip Compensation for Elevators
No. (Addr.) Name
S2-01
Motor Rated Speed
(68FH)
S2-02
(690H) Slip Compensation Gain in
Motoring Mode
S2-03
(691H)
Slip Compensation Gain in
Regenerative Mode
240
All Modes
0: U2- and U3- monitor data is not reset when the drive is initialized (A1-03).
1: Resets the data for the U2- and U3-
key is pressed, fault data is erased and the display returns to 0.
All Modes
0: U4-10 and U4-11 monitor data is not reset when the drive is initialized (A1-03).
1: Resets the kWh counter. The monitors U4-10 and U4-11 will display "0" after they are
initialized. Once o4-12 is set to 1 and the ENTER key is pressed, kWh data is erased and the
display returns to 0.
All Modes
0: Keep the number of travels counter value. The counter is not reset when the drive is
initialized (A1-03).
1: Resets the number 0 travels counter. The monitor U4-24/25 will show 0. Once o4-13 is set to
1 and the ENTER key is pressed, the counter value is erased and the display returns to 0.
All Modes
Determines the speed to begin applying DC Injection (or Position Lock) when the drive is
ramping to stop (b1-03 = 0). Set as a percentage of the maximum output frequency (E1-04).
All Modes
Determines the amount of current to use for DC Injection at start. Set as a percentage of the
drive rated current.
All Modes
Determines the amount of current to use for DC Injection at stop. Set as a percentage of the
drive rated current.
All Modes
Determines how long the drive should perform DC Injection at start. In CLV and CLV/PM, S1-
04 determines how long Position Lock should be performed. A setting of 0.00 disables S1-04.
All Modes
Determines how long the drive should perform DC Injection at stop. In CLV and CLV/PM, S1-
05 determines how long Position Lock should be performed. A setting of 0.00 disables S1-05.
All Modes
Determines the delay time between the start of DC injection/Position Lock and setting the brake
control command (H2- =50) in order to release the brake at the beginning of the ride.
All Modes
Determines the delay time between reaching Zero Speed (S1-01) and resetting the brake control
command (H2- = 50) in order to apply the brake at the end of the ride.
All Modes
Sets the time that must pass after the Up/Down command is entered until the drive internal Run
command is set and the ride is started.
All Modes
Determines the delay time between shutting off the output of the drive and resetting the
contactor control command (H2-
has finished.
V/f OLV
Sets the motor rated speed.
V/f OLV
Slip compensation for leveling speed can be set separately for motoring and regenerative states.
This can help improve the accuracy of leveling.
YASKAWA EUROPE SIEP
Description
monitors. Once o4-11 is set to 1 and the ENTER
Description
= 51) in order to release the motor contactor after a ride
Description
V/f w PG OLV w PG
V/f w PG OLV w PG
Setting
common_
TMonly
Default: 0
Min: 0
Max: 1
common_
TMonly
Default: 0
Min: 0
Max: 1
common_
TMonly
Default: 0
Min: 0
Max: 1
Setting
common_
Default:
<5>
TMonly
Min: 0.000%
Max: 9.999%
common_
Default: 50%
TMonly
Min: 0%
Max: 75%
common_
Default: 50%
TMonly
Min: 0%
Max: 75%
common_
Default: 0.40s
TMonly
Min: 0.00 s
Max: 10.00 s
common_
Default: 0.60s
TMonly
Min: 0.00 s
Max: 10.00 s
common_
Default: 0.20s
TMonly
Min: 0.00 s
Max: 10.00 s
common_
Default: 0.10s
TMonly
Min: 0.00 s
Max: [S1-05]
common_
Default: 0.10s
TMonly
Min: 0.00 s
Max: 10.00 s
common_
TMonly
Default: 0.10s
Min: 0.00 s
Max: 1.00 s
Setting
common_ Default: 1380 rpm
TMonly
Min: 300 rpm
Max: 1800 rpm
Default: 0.7
Min: 0.0
common_
Max: 5.0
TMonly
Default: 1.0
Min: 0.0
Max: 5.0
YASKAWA AC Drive L1000V Technical Manual
Page
154
154
155
Page
156
156
156
156
156
156
157
157
157
Page
157
157
157