C: Tuning - YASKAWA L1000V Technical Manual

No.(Addr.) Name
b1-08 Up/Down Command Selection
(187H) while in Programming Mode
b1-14
Phase Order Selection
(1C3H)
n
b4: Delay Timers
No.(Addr.) Name
b4-01
Timer Function On-Delay Time
(1A3H)
b4-02
Timer Function Off-Delay Time
(1A4H)
n
b6: Dwell Function
No.(Addr.) Name
b6-01
Dwell Speed at Start
(1B6H)
b6-02
Dwell Time at Start
(1B7H)
b6-03
Dwell Speed at Stop
(1B8H)
b6-04
Dwell Time at Stop
(1B9H)
u C: Tuning
C parameters are used to adjust the acceleration and deceleration ramps, jerk settings, slip compensation, torque
compensation, and carrier frequency selections.
n
C1: Acceleration and Deceleration Ramps
No.(Addr.) Name
C1-01
(200H)
Acceleration Ramp 1
C1-02
(201H)
Deceleration Ramp 1
C1-03
(202H)
Acceleration Ramp 2
C1-04
(203H)
Deceleration Ramp 2
C1-05
(204H)
Acceleration Ramp 3
C1-06
(205H)
Deceleration Ramp 3
C1-07
(206H)
Acceleration Ramp 4
C1-08
(207H)
Deceleration Ramp 4
YASKAWA EUROPE SIEP
All Modes
0: Up/Down command not accepted while in the Programming Mode.
1: Up/Down command accepted while in the Programming Mode.
2: Prohibit entering Programming Mode during run.
All Modes
0: U-V-W
1: U-W-V
All Modes
Used to set the on-delay and off-delay times for a digital timer output (H2-
is triggered by a digital input programmed to H1-
All Modes
Parameters b6-01 and b6-02 set the speed to hold and the time to maintain that speed at start.
Parameters b6-03 and b6-04 set the speed to hold and the time to maintain that speed at stop.
All Modes
Sets the ramp to accelerate from 0 to maximum speed.
All Modes
Sets the ramp to decelerate from maximum speed to 0.
All Modes
Sets the ramp to accelerate from 0 to maximum speed.
All Modes
Sets the ramp to decelerate from maximum speed to 0.
All Modes
Sets the ramp to accelerate from 0 to maximum speed.
All Modes
Sets the ramp to decelerate from maximum speed to 0.
All Modes
Sets the ramp to accelerate from 0 to maximum speed.
All Modes
Sets the ramp to decelerate from maximum speed to 0.
YASKAWA AC Drive L1000V Technical Manual
Description
Description
=12). The output
=18)
Description
Description
B.3 Parameter Table
Setting Page
common_
TMonly
Default: 1
Min: 0
Max: 2
common_
Default: 0
TMonly
Min: 0
Max: 1
Setting Page
Default: 0.0 s
Min: 0.0 s
common_
TMonly Max: 3000.0 s
Default: 0.0 s
Min: 0.0 s
Max: 3000.0 s
Setting Page
Default: 0.0%
Min: 0.0%
Max: 100.0%
Default: 0.0 s
Min: 0.0 s
common_
TMonly Max: 10.0 s
Default: 0.0%
Min: 0.0%
Max: 100.0%
Default: 0.0 s
Min: 0.0 s
Max: 10.0 s
Setting Page
common_
TMonly
common_
TMonly
common_
TMonly
common_
TMonly
Default: 1.50 s
<6> <8>
Min: 0.00 s
Max: 600.00 s
<6> <8>
common_
TMonly
common_
TMonly
common_
TMonly
common_
TMonly
106
107
107
107
108
108
108
108
109
109
109
109
109
109
109
B
109
225