YASKAWA L1000V Technical Manual page 271

No.
H1-07 Terminal S7 Function Selection
H2-01 Terminals MA-MB-MC Function Selection
H2-02 Terminals P1-PC Function Selection
H2-03 Terminal MD-ME-MF Function Selection
H4-01 Terminal AM Monitor Selection
H4-02 Terminal AM Gain
H4-03 Terminal AM Bias
H6-01 Terminal RP Function Selection
H6-03 Terminal RP Gain
H6-04 Terminal RP Bias
H6-05 Pulse Train Input Filter Time
H6-09 PG Pulse Number
L1-01 Motor Overload Protection Selection
L1-02 Motor Overload Protection Time
L1-13 Continuous Electrothermal Operation Selection
L2-05 Undervoltage Detection Level (Uv)
L3-01 Stall Prevention Selection during Acceleration
L3-02 Stall Prevention Level during Acceleration
L3-03 Stall Prevention Limit during Acceleration
L3-05 Stall Prevention Selection during Run
L3-06 Stall Prevention Level during Run
L4-01 Speed Agreement Detection Level
L4-02 Speed Agreement Detection Width
L4-03 Speed Agreement Detection Level (+/-)
L4-04 Speed Agreement Detection Width (+/-)
L5-01 Number of Auto Reset Attempts
L5-02 Fault Output Operation during Auto Reset
L5-04 Fault Reset Interval Time
L5-06 Undervoltage Fault Reset Selection
L6-01 Torque Detection Selection 1
L6-02 Torque Detection Level 1
L6-03 Torque Detection Time 1
L6-04 Torque Detection Selection 2
L6-05 Torque Detection Level 2
L6-06 Torque Detection Time 2
L7-01 Forward Torque Limit
L7-02 Reverse Torque Limit
L7-03 Forward Regenerative Torque Limit
L7-04 Reverse Regenerative Torque Limit
L7-06 Torque Limit Integral Time
L7-07 Torque Limit Control Method during Accel/Decel
L8-02 Overheat Alarm Level
L8-03 Overheat Pre-Alarm Operation Selection
L8-05 Input Phase Loss Protection Selection
L8-07 Output Phase Loss Protection Selection
L8-09 Output Ground Fault Detection Selection
L8-10 Heatsink Cooling Fan Operation Selection
L8-11 Heatsink Cooling Fan Off Delay Time
L8-12 Ambient Temperature Setting
L8-15 oL2 Characteristics Selection at Low Speeds
L8-18 Soft CLA Selection
L8-19 Frequency Reduction Rate during oH Pre-Alarm
L8-35 Installation Selection
L8-38 Automatic Torque Boost Selection
L8-40 Carrier Frequency Reduction Off-Delay Time
L8-41 High Current Alarm Selection
L8-43 Output Phase Loss Detection Time
L8-88 Safe Disable Operation Mode
n2-01 Speed Feedback Detection Control (AFR) Gain
n2-02 Speed Feedback Detection Control (AFR) Time Constant 1
n2-03 Speed Feedback Detection Control (AFR) Time Constant 2
n6-01 Online Tuning Selection
o1-01 Drive Mode Unit Monitor Selection
o1-02 User Monitor Selection After Power Up
o1-03 Digital Operator Display Unit Selection
YASKAWA EUROPE SIEP
User
Name
Setting
YASKAWA AC Drive L1000V Technical Manual
No. Name
o1-10 User-Set Display Units Maximum Value
o1-11 User-Set Display Units Decimal Display
o2-01 LO/RE Key Function Selection
o2-02 STOP Key Function Selection
o2-03 User Parameter Default Value
o2-04 Drive Model Selection
o2-05 Speed Reference Setting Method Selection
Operation Selection when Digital Operator is
o2-06
Disconnected
o2-07 Motor Direction at Power Up When using Operator
o2-09 Initialization Specification
o3-01 Copy Function Selection
o3-02 Copy Allowed Selection
o4-01 Cumulative Operation Time Setting
o4-02 Cumulative Operation Time Selection
o4-03 Cooling Fan Operation Time Setting
o4-05 Capacitor Maintenance Setting
o4-07 DC Bus Pre-charge Relay Maintenance Setting
o4-09 IGBT Maintenance Setting
o4-11 U2, U3 Initialization
o4-12 kWh Monitor Initialization
o4-13 Number of Travels Counter Reset
S1-01 Zero Speed Level at Stop
S1-02 DC Injection Current at Start
S1-03 DC Injection Current at Stop
S1-04 DC Injection Position Lock Time at Start
S1-05 DC Injection Position Lock Time at Stop
S1-06 Brake Release Delay Time
S1-07 Brake Close Delay Time
S1-10 Run Command Delay Time
S1-11 Output Contactor Open Delay Time
S2-01 Motor Rated Speed
S2-02 Slip Compensation Gain in Motoring Mode
S2-03 Slip Compensation Gain in Regenerative Mode
S2-05 Slip Compensation Torque Detection Delay Time
S2-06 Slip Compensation Torque Detection Filter Time Constant
S4-01 Light Load Direction Search Selection
S4-02 Light Load Direction Search Method
S4-03 Light Load Direction Search Time
S4-04 Light Load Direction Search Speed Reference
S4-05 Rescue Operation Torque Limit
Motor Contactor Response Error (SE1) Detection/Reset
S6-01
Selection
S6-02 Starting Current Error (SE2) Detection Delay Time
S6-04 Output Current Error (SE3) Detection Delay Time
S6-05 Brake Response Error (SE4) Detection Time
S6-15 Speed Reference Loss Detection
S6-16 Restart after Baseblock Selection
S6-20 Rollback Detection Operation Selection
T1-01 Auto-Tuning Mode Selection
T1-02 Motor Rated Power
T1-03 Motor Rated Voltage
T1-04 Motor Rated Current
T1-05 Motor Base Frequency
T1-06 Number of Motor Poles
T1-07 Motor Base Speed
o1-11 User-Set Display Units Decimal Display
o2-01 LO/RE Key Function Selection
o2-02 STOP Key Function Selection
D.3 User Setting Table
User
Setting
271
D