Table of Contents
Advertisement
Standards and Service Limits
r-
A
. T
utomatlc ransmlsslon cont
'd)
-
S
ectlon 14
STANDARD INEW)
MEASUREMENT
Wire
Dia.
O.D.
Free Length
NO.ofeoils
Springs
Regulator valve spring A
1.810.071)
14.710.579)
87.813.457)
16.5
Regulator valve spring B
1.810.071)
9.610.378)
44.0 11.732)
11.0
Stator reaction spring
4.510.1771
35.411.394)
30.311.193)
1.9
Modulator valve spring
1.410.055)
9.410.370)
35.011.378)
10.9
Torque converter check valve spring
'97 model
1.1 10.043)
8.410.331)
36.411.433)
12.0
'98 - 00 models
1.210.047)
8.410.331)
32.411.276)
12.7
Cooler relief valve spring
1.010.039)
8.410.331)
33.811.331)
8.2
Relief valve spring
1.1 10.043)
8.610.339)
37.111.461)
13.4
2nd orifice control valve spring
0.710.028)
6.610.260)
34.811.370)
22.0
1-2 shift valve spring
0.910.035)
7.610.299)
41.311.626)
16.3
2-3 shift valve spring
0.910.035)
7.610.2991
57.012.244)
26.8
3-4 shift valve spring
0.910.035)
7.610.299)
57.012.244)
26.8
1st accumulator spring
2.1 10.083)
16.0 10.630)
89.1 13.508)
16.2
4th accumulator spring B
2.310.0911
10.2 10.402)
51.612.031)
13.8
4th accumulator spring A
2.610.1021
17.0 10.669)
88.4 13.4801
14.2
2nd accumulator spring A
2.410.094)
29.011.142)
39.0 11.535)
2.9
3rd accumulator spring A
2.810.1101
17.510.689)
94.313.713)
15.9
2nd accumulator spring B
1.610.0631
9.010.354)
20.710.815)
6.1
3rd accumulator spring B
2.1 10.083)
31.0 11.220)
38.211.504)
2.6
3rd sub accumulator spring
2.710.106)
17.010.669)
39.011.535)
6.3
2nd accumulator spring C
2.210.087)
14.510.571)
68.0 12.6771
13.9
Lock-up shift valve spring
0.910.035)
7.610.299)
73.712.902)
32.0
Lock-up timing valve spring
0.910.035)
8.1 10.319)
81.4 13.205)
47.8
lock-up control valve spring
0.710.028)
6.610.260)
38.011.496)
14.1
3-4 orifice control valve spring
0.610.024)
6.610.260)
37.911.492)
31.6
Servo control valve spring
1.010.039)
8.1 10.319)
52.112.051)
20.8
CPB valve spring
0.910.035)
8.1 10.319)
47.211.858)
18.3
4th exhaust valve spring
0.910.035)
6.1 10.240)
36.411.433)
19.5
-
Differential (4WD) - Section 15
MEASUREMENT
STANDARD INEW)
Differential
Capacity
flUS qt, Imp qti
1.2 (1.3, 1.1) at overhaul
fluid
1.0 (1.1, 0.9) at fluid change
-
Steering - Section 17
MEASUREMENT
STANDARD INEW)
Steering wheel
Rotational play at steering wheel circumference
0- 10 10 - 0.39)
Starting load at steering wheel circumference
N Ikg!, (bt)
Engine running
29 13.0, 6.6)
Gearbox
Angle ot rack-guide-screw loosened from locked position
'97, '98 models
10°
±
50
'99, '00 models
20' MAX.
Pump
Pump pressure with shut-off valve closed
6,900 - 7,800 170 - 80, 995 - 1,138)
kPa (kgt/cm2, psi)
Power steering
Recommended fluid
Honda power steering fluid.
fluid
Fluid capacity
For overhaul
0.8510.90,0.75)
I IUS qt, Imp qt)
For reservoir
0.4 10.42, 0.351
Power steering
Deflection with 98 N (10 kgf, 22 Ibt)
11.0 - 14.5 (0.43 - 0.57) with used belt
belt·
between pulleys
7.5
-
10.0 (0.30 - 0.40) with new belt
Belt tension
N Ikgt, Ibtl
390 - 540 (40 - 55, 88
-
121) with used belt
Measured with belt tension gauge
740-880 (75-90,165-198) with new belt
• When uSing a new belt. adjust deflection or tensIOn to new values. Run the engme for 5 minutes then turn It off.
0"'''',.,;" ..... ,.,
...
-1' 1 ........ ;" .......
~.~
... _;" .......
"
.......
,.,
10.
....
1.
,
... 1,,_
....
2-10
Advertisement
Table of Contents
Troubleshooting
