Honda CR-V 1997 Service Manual page 764

Transfer Assembly
Reassembly (cont'd)
35. Remove transfer cover A.
36. If the measurement is out of specification, remove
the 68 mm thrust shim from transfer cover A
by
heating the cover to almost 212°F
(10QoC)
using a
heat gun. Do not heat the cover higher than 212°F
(10QoC).
Let the cover cool to room temperature
before adjusting the starting torque.
If the measurement is within the specification, go to
step 40.
HEAT GUN
TRANSFER COVER A
BEARING OUTER RACE
14-248
37. Select the 68 mm thrust shim.
THRUST SHIM, 68 mm
Shim No.
Part Number Thickness
ZV 23974 - PIC - 020
1.41 mm (0.056 in)
ZW 23975 - PIC - 020 1.44 mm (0.057 in)
ZX 23976 - PIC - 020
1.47 mm (0.058 in)
ZY 23977 - PIC - 020
1.50 mm (0.059 in)
ZZ 23978 - PI C - 020
1.53 mm (0.060 in)
A 23941 - PW5 - 000 1.56 mm (0.061 in)
B 23942 - PW5 - 000 1.59 mm (0.063 in)
C
23943 - PW5 - 000
1.62 mm (0.064 in)
D 23944 - PW5 - 000
1.65
mm
(O.065
in)
E 23945 - PW5 - 000 1.68 mm (0.066 in)
F
23946 - PW5 - 000 1.71 mm (0.067 in)
G 23947 - PW5 - 000
1.74 mm (0.069 in)
H 23948 - PW5 - 000 1.77 mm (0.070 in)
I 23949 - PW5 - 000 1.80 mm (0.071 in)
J 23950 - PW5 - 000 1.83 mm (0.072 in)
K 23951 - PW5 - 000 1.86 mm (0.073 in)
L 23952 - PW5 - 000 1.89 mm (0.074 in)
M 23953 - PW5 - 000
1.92 mm (0.076 in)
N 23954 - PW5 - 000
1.95 mm (0.077 in)
0
23955 - PW5 - 000
1.98 mm (0.078 in)
P 23956 - PW5 - 000
2.01 mm (0.079 in)
Q 23957 - PW5 - 000 2.04 mm (0.080 in)
A
23958 - PW5 - 000 2.07 mm (0.081 in)
S 23959 - PW5 - 000 2.10 mm (0.083 in)
T 23960 - PW5 - 000 2.13 mm (0.084 in)
U
23961 - PW5 - 000 2.16 mm (0.085 in)
V 23962 - PW5 - 000
2.19 mm (0.086 in)
W 23963 - PW5 - 000 I
2.22 mm (0.087 in)
X 23964 - PW5 - 000
2.25 mm (0.089 in)
y
23965 - PW5 - 000
2.28 mm (0.090 in)
Z
23966 - PW5 - 000
2.31 mm (0.091 in)
AA 23967 - PW5 - 000
2.34 mm (0.092 in)
AB
23968 - PW5 - 000
2.37 mm (0.093 in)
AC 23969 - PW5 - 000 2.40 mm (0.094 in)
AD 23970 - PW5 - 000 2.43 mm (0.096 in)
AZ 23941 - PW8 - 000
2.46 mm (0.097 in)
BZ 23942 - PW8 - 000 2.49 mm (0.098 in)
CZ 23943 - PW8 - 000
2.52 mm (0.099 in)
DZ 23944 - PW8 - 000 2.55 mm (0.100 in)
EZ 23945 - PW8 - 000 2.58 mm (0.102 in)