Honda CR-V 1997 Service Manual page 33

Standards and Service Limits
- Automatic Transmission (cont'd)- Section 14
MEASUREMENT
STANDARD (NEW)
SERVICE LIMIT
Transmission
Diameter of needle bearing contact area
On mainshaft stator shaft bearing
23.980 - 23.993 10.9441 - 0.9446)
Wear or damage
On mainshaft 2nd gear
35.975 - 35.991 11.4163 - 1.4169)
On mainshaft 4th gear collar
31.975 - 31.991 11.2589 - 1.2595)
On mainshaft 1st gear collar
30.975 - 30.991 11.2195 - 1.2201)
On countershaft (torque converter housing side)
36.004 - 36.017 11.4175 - 1.4180)
On countershaft 3rd gear
35.980 - 35.996 11.4165 - 1.4172)
On countershaft 4th gear
27.980 - 27.993 11.1016 - 1.1021)
On countershaft reverse gear collar
31.975- 31.99111.2589 -1.2595)
On
counters haft
1 st gear collar
31.975- 31.99111.2589 -1.2595)
On sub-shaft (transmission housing side)
25.991 - 26.000 11.0233 - 1.0236)
On sub-shaft 4th gear collar
22.9935 - 23.0065 10.9053 - 0.9058)
On reverse idler gear shaft
13.990 - 14.000 10.5508 - 0.5512)
Wear or damage
Inside diameter of needle bearing contact area
On mainshaft 1st gear
35.000 - 35.016 11.3780 - 1.3786) Wear or damage
On mains haft 2nd gear 41.000- 41.01611.6142 -1.6148)
On
mains haft
4th gear
38.000 - 38.016 11.4961 - 1.4967)
On counters haft 1 st gear
38.000-38.01611.4961 -1.4967)
On countershaft 3rd gear
41.000 - 41.016 11.6142 - 1.6148)
On countershaft 4th gear
33.000 - 33.016 11.2992 - 1.2998)
On countershaft reverse gear
38.000-38.01611.4961 -1.4967)
On sub-shaft 4th gear
32.000 - 32.016 11.2598 - 1.2605)
On reverse idler gear
18.007 - 18.020 10.7089 - 0.7094)
Reverse idler gear shaft holder 1.0.
14.416 - 14.434 10.5676 - 0.5683) Wear or damage
End play
Mainshaft 1st gear
0.05 - 0.16 (0.002 - 0.006)
- -
Mainshaft 2nd gear
0.05 - 0.13 10.002 - 0.005)
- -
Mainshaft 4th gear
0.05 - 0.16 (0.002 - 0.006)
- -
Countershaft 1 st gear
0.1 - 0.5 10.004 - 0.020)
- -
Counters haft 3rd gear
0.05 - 0.17 (0.002 - 0.007)
- -
Countershaft 4th gear
0.10 - 0.18 (0.004 - 0.007) - -
Sub-shaft 4th gear
0.05 - 0.17 (0.002 - 0.007)
- -
Reverse idler gear
0.05 - 0.1810.002 - 0.007)
- -
Counters haft reverse gear
0.10 - 0.25 (0.004 - 0.010)
- -
Selector hub 0.0.
51.87 - 51.90 (2.042 - 2.043)
Wear or damage
Mainshaft 4th gear collar length
49.50 - 49.55 (1.9488 - 1.9508)
- -
Mainshaft 4th gear collar flange thickness
4.435 - 4.525 (0.1746 - 0.1781)
Wear or damage
Mainshaft 1st gear collar length
27.00 - 27.05 (1.063 - 1.065)
- -
Countershaft distance collar length
38.97 - 39.00 11.534 - 1.535)
- -
39.02 - 39.05 11.536 - 1.537)
- -
39.07 - 39.10 11.538 - 1.539)
- -
39.12 - 39.1511.540 - 1.541)
- -
39.17 - 39.20 11.542 - 1.543)
- -
39.22 - 39.25 (1.544 - 1.545)
- -
39.27 - 39.30 11.546 - 1.547)
- -
38.87 - 38.90 (1.530 - 1.531 )
- -
38.92 - 38.95 11.532 - 1.533)
- -
Countershaft 3rd gear collar length
21.15 - 21.20 10.8327 - 0.8346)
- -
Countershaft reverse gear collar length
14.5 - 14.6 10.571 - 0.575)
- -
Countershaft. reverse gear collar flange
thickness
2.4 - 2.6 (0.094 - 0.102)
Wear or damage
Countershaft 1st gear collar length
14.5 - 14.6 (0.571 - 0.575)
- -
Countershaft 1st gear collar flange thickness
2.4 - 2.6 10.094 - 0.102)
Wear or damage
Sub-shaft 4th gear collar length
24.0 - 24.1 (0.945 - 0.949)
- -
Sub-shaft 4th gear collar flange thickness 2.95 - 3.10 10.116 - 0.122) Wear or damage
2-8