Huawei quidway s7700 Configuration Manual page 761

Quidway S7700 Smart Routing Switch
Configuration Guide - VPN
[PE2] mpls lsr-id 3.3.3.9
[PE2] mpls
[PE2-mpls] mpls te
[PE2-mpls] mpls rsvp-te
[PE2-mpls] mpls te cspf
[PE2-mpls] quit
[PE2] interface vlanif 30
[PE2-Vlanif30] mpls
[PE2-Vlanif30] mpls te
[PE2-Vlanif30] mpls rsvp-te
[PE2-Vlanif30] quit
Step 4 Configure OSPF TE on the backbone network.
# Configure PE1.
[PE1] ospf
[PE1-ospf-1] opaque-capability enable
[PE1-ospf-1] area 0.0.0.0
[PE1-ospf-1-area-0.0.0.0] network 1.1.1.9 0.0.0.0
[PE1-ospf-1-area-0.0.0.0] network 100.1.1.0 0.0.0.255
[PE1-ospf-1-area-0.0.0.0] mpls-te enable
# Configure the P device.
[P] ospf
[P-ospf-1] opaque-capability enable
[P-ospf-1] area 0.0.0.0
[P-ospf-1-area-0.0.0.0] network 2.2.2.9 0.0.0.0
[P-ospf-1-area-0.0.0.0] network 100.1.1.0 0.0.0.255
[P-ospf-1-area-0.0.0.0] network 100.2.1.0 0.0.0.255
[P-ospf-1-area-0.0.0.0] mpls-te enable
# Configure PE2.
[PE2] ospf
[PE2-ospf-1] opaque-capability enable
[PE2-ospf-1] area 0.0.0.0
[PE2-ospf-1-area-0.0.0.0] network 3.3.3.9 0.0.0.0
[PE2-ospf-1-area-0.0.0.0] network 100.2.1.0 0.0.0.255
[PE2-ospf-1-area-0.0.0.0] mpls-te enable
Step 5 Configure tunnel interfaces.
# Create tunnel interfaces on PEs. Specify MPLS TE as the tunneling protocol and RSVP-TE
as the signaling protocol.
# Configure PE1.
[PE1] interface tunnel 1/0/0
[PE1-Tunnel1/0/0] ip address unnumbered interface loopback1
[PE1-Tunnel1/0/0] tunnel-protocol mpls te
[PE1-Tunnel1/0/0] destination 3.3.3.9
[PE1-Tunnel1/0/0] mpls te tunnel-id 100
[PE1-Tunnel1/0/0] mpls te reserved-for-binding
[PE1-Tunnel1/0/0] mpls te commit
# Configure PE2.
[PE2] interface tunnel 1/0/0
[PE2-Tunnel1/0/0] ip address unnumbered interface loopback1
[PE2-Tunnel1/0/0] tunnel-protocol mpls te
[PE2-Tunnel1/0/0] destination 1.1.1.9
[PE2-Tunnel1/0/0] mpls te tunnel-id 100
[PE2-Tunnel1/0/0] mpls te reserved-for-binding
[PE2-Tunnel1/0/0] mpls te commit
Issue 01 (2011-07-15) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
7 VPLS Configuration
746