Huawei quidway s7700 Configuration Manual page 49

Quidway S7700 Smart Routing Switch
Configuration Guide - VPN
# Enable OSPF on the devices along the TE tunnel so that the devices can transmit TE attributes.
# Configure PE1.
[PE1] ospf 1
[PE1-ospf-1] opaque-capability enable
[PE1-ospf-1] area 0
[PE1-ospf-1-area-0.0.0.0] mpls-te enable
[PE1-ospf-1-area-0.0.0.0] quit
[PE1-ospf-1] quit
# Configure PE1.
[PE2] ospf 1
[PE2-ospf-1] opaque-capability enable
[PE2-ospf-1] area 0
[PE2-ospf-1-area-0.0.0.0] mpls-te enable
[PE2-ospf-1-area-0.0.0.0] quit
[PE2-ospf-1] quit
# By running the display interface tunnel interface-number command on the PEs, you can see
that Tunnel1/0/1 and Tunnel1/0/2 are both Up. Take Tunnel1/0/2 on PE1 for example.
[PE1] display interface Tunnel 1/0/2
Tunnel1/0/2 current state : UP
Line protocol current state : UP
Last line protocol up time : 2007-09-10 13:54:57-08:00
Description:HUAWEI, Quidway Series, Tunnel1/0/0 Interface
Route Port,
Internet Address is unnumbered, using address of LoopBack0(1.1.1.1/32)
Encapsulation is TUNNEL, loopback not set
Tunnel destination 2.2.2.2
Tunnel up/down statistics 1
Tunnel protocol/transport MPLS/MPLS, ILM is available,
primary tunnel id is 0x1003d, secondary tunnel id is 0x0
QoS max-bandwidth : 64 Kbps
Output queue : (Urgent queue : Size/Length/Discards)
Output queue : (Protocol queue : Size/Length/Discards) 0/1000/0
Output queue : (FIFO queue : Size/Length/Discards)
Step 4 Configure VPN instances on each PE and connect the CEs to the PEs.
# Configure PE1.
[PE1] ip vpn-instance VPNA
[PE1-vpn-instance-VPNA] route-distinguisher 100:1
[PE1-vpn-instance-VPNA] vpn-target 111:1 both
[PE1-vpn-instance-VPNA] quit
[PE1] ip vpn-instance VPNB
[PE1-vpn-instance-VPNB] route-distinguisher 100:2
[PE1-vpn-instance-VPNB] vpn-target 222:2 both
[PE1-vpn-instance-VPNB] quit
[PE1] interface vlanif 30
[PE1-Vlanif30] ip binding vpn-instance VPNA
[PE1-Vlanif30] ip address 10.1.1.2 30
[PE1-Vlanif30] quit
[PE1] interface vlanif 20
[PE1-Vlanif20] ip binding vpn-instance VPNB
[PE1-Vlanif20] ip address 10.2.1.2 30
[PE1-Vlanif20] quit
Issue 01 (2011-07-15)
300 seconds output rate 0 bits/sec, 0 packets/sec
196 seconds output rate 0 bits/sec, 0 packets/sec
0 packets output, 0 bytes
0 output error
0 output drop
Input bandwidth utilization
Output bandwidth utilization : --
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
1 VPN Tunnel Management Configuration
0/256/0
: --
0/50/0
34