Hitachi GR2000 Series Configuration Commands page 475

Table 5-10 MPLS Information Error Messages [ROUTE-OS7] (continued)
label_switched_path: the explicit_route_name
'<ER name>' for the
secondary_label_switched_path should not
be the same explicit_route_name for the
label_switched_path in '<LSP name>'
label_switched_path: vpn is necessary in
'<LSP name>'
label_switched_path: When VPN and
flow_map are set up, ether one only a side is
possible in '<LSP name>'
label_switched_path: When VPN and
policy_mpls in flow block are set up, either
one only a side is possible in '<LSP name>'
label_switched_path:'<ER name>' is
necessary
ldp: Can not change IP address
ldp: duplicate failed_init_session_threshold
ldp: duplicate keep_alive_hold_timer
ldp: invalid failed_init value '<Value>' not in
range 0 to 65535
ldp: invalid IP address '<Address>'
ldp: invalid keep_alive value '<HoldTimer>'
not in range 1 to 65535
ldp: ip address '<Address>' is already used in
other ldp
ldp: IP address is mandatory
lsr: duplicate hop_count_limit
lsr: duplicate loop_detection
lsr: duplicate path_vector_limit
lsr: invalid hop_count_limit value '<Value>'
not in range 2 to 255
lsr: invalid path_vector_limit value '<Value>'
not in range 2 to 255
MPLS is not supported
mpls syntax error
mpls: Can not change '<ER name>' with used The "route name" whose route was tried to be changed is being
mpls: Can not delete '<ER name>' with used
mpls: Can not set IPv6 IP_Address
GR2K-GA-0014
Ver. 07-02
The name is incorrect. For lsp and secondary lsp, designate
separate explicit_route_name.
<ER name>: Specified route name
<LSP name>: Specified LSP name
In setting remote_vpn, specify vpn.
<LSP name>: Specified LSP name
The flow_map and the vpn cannot be set simultaneously.
<LSP name>: Specified LSP name
Simultaneous setting is not permitted for policy_mpls parameters of
the flow filter and vpn parameters of label_switched_path. Do not
specify LSP that uses VPN functions for a policy_mpls parameter of
the flow filter. Also, do not make VPN settings for LSP that has been
specified for a policy_mpls parameter of the flow filter.
<LSP name>: Specified LSP name
Unregistered explicit_route_name was designated. Or, an attempt
was made to delete the explicit_route_name being used. Designate
the registered explicit_route_name.
<ER name>: Specified route name
IP address can not change.
This is a duplicated definition.
This is a duplicated definition.
failed_init is out of range. Specify a value within the range of 0 to
65535.
<Value>: failed_init value
IP address is invalid
<Address>: Specified address
keep_alive value is out of range. Specify a value within the range of 1
to 65535.
<HoldTimer>: HoldTimer value
Designate the IP address which has not been designated in the
separate block.
<Address>: Specified address
The IP address is a must.
This is a duplicated definition.
This is a duplicated definition.
This is a duplicated definition.
hop_count_limit value is out of range. Specify a value within the
range of 2 to 255.
<Value>
path_vector_limit value is out of range. Specify a value within the
range of 2 to 255.
<Value>: path_vector_limit value
MPLS is not supported
MPLS configuration information is invalid.
Set the correct configuration information.
used.
<ER name>: Specified route name
The "route name" whose route was tried to be deleted is being used.
<ER name>: Specified route name
It is not possible to set IPv6 addresses in MPLS information.
Configuration Error Messages
5-85