Hitachi GR2000 Series Configuration Commands page 417

Table 5-5
bgp: This peer address <Peer> matches the
local router id <Address>
bgp4+: address should not be::
bgp4+: address should not be v4-compat
bgp4+: address should not be v4-mapped
bgp4+: as-count only makes sence with
external peers
bgp4+: as-count optionis not supported the
policy group
bgp4+: as-override may only be used with
external peers
bgp4+: as-override option must be the same
in the policy group
bgp4+: aspath-opt option is not supported the
policy group
bgp4+: authmd5 must be equal to or greater
than one character
bgp4+: authmd5 "<MD5>" longer than 80
characters
bgp4+:autonomous-system not specified
bgp4+: BGP4+ local-address <IPv6 Prefix> is
not global/site-local IPv6 address
bgp4+: clusterid may not be 0.0.0.0
bgp4+: confederation peer must have the
member AS
bgp4+: description "<Name>" longer than 64
characters
bgp4+: description may only be used with
peers
bgp4+: disable may only be used with peers
bgp4+: duplicate bgp4+ clause
bgp4+: duplicate BGP4+ group found, groups
must differ by type and/or AS
bgp4+: duplicate entries for peer <Peer>
found in group type <Type> AS <As>
GR2K-GA-0014
Ver. 07-02
Routing Protocol Error Messages (continued)
Peer address is the same as router ID of local router. Specify a peer
address different from router ID.
<Peer>: Specified peer address
<Address>: Local router ID
Default address is specified in address. Specify addresses other than
the local host address.
An IPv4-compatible address is specified in an address.
Specify addresses other than the IPv4-compatible address.
An IPv4 mapped address is specified in an address.
Specify addresses other than the IPv4 mapped address.
An as-count parameter is specified using peers other than the
external peer. Do not specify the as-count parameter using an
internal peer and routing peer.
An as-count option is specified in the policy group.
Specify an as-count option on the Export filter side.
An as-override option is defined in peers other than the external
peer.
An as-override option can be used only in the external peer.
as-override options are different in the policy group.
as-override options must be the same in the policy group.
An Aspath-opt option is specified in the policy group. Specify an
Aspath-opt option on the Export filter side.
The designated authentication key is less than one character.
Designate the authentication key using between 1 and 80
characters.
The designated authentication key is longer than 80 characters.
Designate the authentication key by using less than 80 characters.
<MD5> Specified authentication key.
The AS number to which this router belongs is not defined. Define
the AS number of a local router.
Defined lcladdr is except a global address or site local address.
Define a global address or site local address in lcladdr.
<IPv6 Prefix>: Specified local address
0.0.0.0 is specified in cluster ID.
Specify cluster ID by except 0.0.0.0.
Setting the peer between members requires the member AS number.
Specify the member AS number.
The specified ID exceeds 64 characters. Specify ID by 64 or less
characters.
<Name>: Specified identifier
The description option is specified by other than peer group. The
option for description shall be defined in the peer.
The disable option is specified by other than peer. The option for
disable shall be defined in the peer.
The same peer was duplicated for definition. Do not define the same
peer.
Bgp4+ is double-defined. Delete one of the definitions.
The same peer was duplicated for specification. Do not specify the
same peer.
<Peer>: Specified peer address
<Type>: Specified peer group
<As>: AS number of specified peer group
Configuration Error Messages
5-27