Hitachi GR2000 Series Configuration Commands page 420

Hitachi Gigabit Router GR2000 Series Enhanced Version Configuration Commands, Vol. 2
Table 5-5
bgp4+: the peer group option must be the
same for policy group
bgp4+: the peer option is link-local address,
but the internal peeras group is not supported
link-local address peering
bgp4+:the refresh option must be specified
with ipv6-uni
bgp4+:when the peer address is link-local
address, gateway option must not be
specified
configuration check error
dampen-flap: incorrect suppression
parameters
dampen-flap: invalid keep-history-time value
at <value> not in range 1 to 86400
dampen-flap: invalid max-flap value at
<value> not in range 1 to 30
dampen-flap: invalid reach-decay-time value
at <value> not in range 1 to 3600
dampen-flap: invalid reuse-below value at
<value> not in range 1 to 30
dampen-flap: invalid suppress-above value at
<value> not in range 1 to 30
dampen-flap: invalid unreach-decay-time
value at <value> not in range 1 to 3600
dampen-flap: out of range
dampen-flap: syntax error
export: address not IPv6
export: address should not be::
export: address should not be v4-compat
export: address should not be v4-mapped
export: Attribute-filter " <Name>" cannot be
specified
5-30
Routing Protocol Error Messages (continued)
The settings of peer group option in the policy group are different.
The settings of peer group option in the policy group must be the
same.
The link local address is defined in the address of the internal peer.
Define the global address or site local address in the peer address of
the internal peer.
Parameters other than ipv6-uni are specified in the parameter of a
refresh option. Do not specify parameters other than ipv6-uni in the
parameter of a refresh option.
The peer address is a link local address, but a gateway option is
defined. Do not define a gateway option when a link local address is
defined in the peer address.
Configuration information check error. If the identifiers (<id>) to be
designated by the "attribute-list" command, the "network-filter"
command and the "route-filter" command contain unusable
characters, modify them to the correct identifiers (<id>).
The parameter specified in dampen-flap definition is invalid. Specify
so as to meet the condition of reuse-below < suppress-above
<max-flap.
The specified keep history time is invalid. Specify within the range of
1 to 86400.
<Value>: Specified keep history time
The specified maximum flap value is invalid. Specify within the range
of 1 to 30.
<Value>:Specified maximum flat value
The specified reach decay time is invalid. Specify within the range of
1 to 3600.
<Value>: Specified reach decay time
The specified reuse value is invalid.
Specify within the range of 1 to 30.
<Value>: Specified reuse value
The specified suppress value is invalid. Specify within the range of 1
to 30.
<Value>: Specified suppress value.
The specified unreach decay time is invalid. Specify within the range
of 1 to 3600.
<Value>: Specified unreach decay time
The parameter-specified range is exceeded in the input command
syntax. Numeric values of more than 4294967296 are contained.
Reconfirm a parameter.
Syntax error
Addresses other than an IPv6 prefix are specified.
Specify the IPv6 prefix.
A default address is specified in an address.
Specify addresses other than the local host address.export: address
should not be v4-compatable.
An IPv4-compatible address is specified in an address.
Specify addresses other than the IPv4-compatible address.
An IPv4 mapped address is specified in an address. Specify
addresses other than the IPv4 mapped address.
Filter information inherent to IPv4 is defined in IPv6. Do not specify
the filter information inherent to IPv4.
<Name>: Specified identifier
GR2K-GA-0014
Ver. 07-02