Hitachi GR2000 Series Configuration Commands page 405

Table 5-4
Can not delete policy group configuration with
filter list configuration.
Can not delete policy list configuration with
policy group configuration.
Can not delete relay group configuration with
relay interface configuration.
Can not delete relay list configuration with
relay group configuration.
Can not set ARP configuration.
Can not set IP address on interface which is
not configured to use IP protocol.
Can not set IP address on line router which is
not configured to use IP protocol.
Can not set IP address on non-existing
interface <name>.
Can not set IP address.
Can not set IP configuration on line which is
not bound to IP protocol.
Can not set IP configuration to <name>.
Can not set ip null.
Can not set vlan.
Can not set vpn.
Change is not possible
Connect type is not point.
Destination ip address not specified.
Duplicate destination IP address.
Duplicate interface name and next hop
address.
Duplicate IP address.
Duplicate network address.
Duplicate policy group configuration.
Duplicate pool ip address.
Duplicate prefix.
GR2K-GA-0014
Ver. 07-02
IP Information Error Messages (continued)
IP filter list information exists. Delete IP filter list information; delete
policy group information.
Policy group information exists. Delete policy group information first,
and delete policy group information.
Can not delete relay group configuration with relay interface
configuration. Delete the relay interface information first and then
delete the relay group information.
Can not delete relay list configuration with relay group configuration.
Delete the group first and then delete the list.
ARP is set in other than Ethernet, ATM, or DLCI. ARP can be set
only in Ethernet, ATM, and DLCI. Delete ARP.
IP address cannot be set on the interface not configured to use IP
protocol. Set IP first.
IP address cannot be set on the line router not configured to use IP
protocol. Set IP first.
Specified interface for IP address does not exist. Check the interface.
<name> configuration information name.
Can not set IP address. The IPv6 address cannot be set, if the
interface name type of IP is "group," or if a rmEthernet, AUX, frame
relay or DLCI line is used. IPv6 address settings are not permitted for
an IP that has a VLAN-defined IPv4 address already set.
Attempt made to set IP on the line that is not bound to IP protocol.
Set the protocol first.
Attempt made to set IP in grouped interface or interface where IP is
defined. Check the specified interface. <name> configuration
information name.
Can not set ip null. If 256 interfaces are set for an RP, settings are
impossible. Remove the interface for the RP that has 256 interfaces
set.
Can not set vlan. VLAN can be set only on an Ethernet or a gigabit
Ethernet. If both an IPv4 address and an IPv6 address are set for an
IP, VLAN cannot be set for the IPv4 address on the IP.
Can not set vpn. If PPP and the frame relay IP are defined in the
same physical port, only one of either PPP or the frame relay IP can
be set in VPN settings.
The configuration definition cannot be changed. Set it after deleting
the configuration definition.
IP type is not point. Specify point to the IP type.
Although connection type is point-to-point, a destination address has
not been specified. Or, the PPP line is set or an IPv6 address other
than linklocal is set for TUNNEL. However, settings are not made for
the destination address. Specify destination address.
The same destination IP address is set. Make each destination IP
address unique.
The policy list set has the interface name and the next hop address
with the same contents. Make all policy lists unique.
The same IP address is used. Make each IP address unique.
IP address of the same network address is defined. Specify an IP
address so that each network address becomes unique.
Duplicate policy group configuration. Make settings so that each
policy group entry has unique contents.
The same pool IP addresses are set in the same RP. Make settings
so that pool addresses in the same RP are unique.
Duplicate prefix IP address. Set prefix to unique.
Configuration Error Messages
5-15