Page 1 Hitachi Gigabit Router GR2000 Series Installation Guide GR2K-GA-1002 Rev. 6.03...
Page 2 Internet Explorer is a registered trademark of Microsoft, Corp., USA. Netscape Navigator is a registered trademark of Netscape Communications Corporation. All other brands and product names are trademarks of their respective holders. © Copyright 2001 Hitachi, Ltd. All Rights Reserved. GR2K-GA-1002 Rev. 6.03...
Page 3: Change Record
Hitachi, Ltd. Hitachi, Ltd. reserves the right to make changes to this document at any time without notice, and assumes no responsibility for its use. All the features described in this document may not be currently available.
Page 4 GR2000 Installation Guide Acknowledgments [GateD] Copyright © 1995, 1996, 1997, 1998 The Regents of the University of Michigan. All rights reserved. Gate Daemon was originated and developed through release 3.0 by Cornell University and its collaborators. [SNMP] ***************************************************************************** Copyright 1988-1996 by Carnegie Mellon University. All Rights Reserved Permission to use, copy, modify, and distribute this software and its documentation for any purpose and without fee is hereby granted, provided that the above copyright notice appear in all copies and that both that copyright notice and this permission...
Page 5 Steve Waldbusser * Additional Contributors: Erik Schoenfelder (schoenfr@ibr.cs.tu-bs.de): additions, fixes and enhancements for Linux by 1994/1995. David Waitzman: Reorganization in 1996. Wes Hardaker <hardaker@ece.ucdavis.edu>: Some bug fixes in his UC Davis CMU SNMP distribution were adopted by David Waitzman David Thaler <thalerd@eecs.umich.edu>: Some of the code for making the agent embeddable into another application was adopted by David Waitzman Many more over the years...
Page 6 GR2000 Installation Guide SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Page 7 THIS SOFTWARE IS BEING PROVIDED “AS IS”, WITHOUT ANY EXPRESS OR IMPLIED WARRANTY. IN PARTICULAR, NEITHER THE AUTHOR NOR AT&T MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND CONCERNING THE MERCHANTABILITY OF THIS SOFTWARE OR ITS FITNESS FOR ANY PARTICULAR PURPOSE.
Page 8 GR2000 Installation Guide GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Page 9 WASHINGTON UNIVERSITY IN SAINT LOUIS Copyright © 1993, 1994 Washington University in Saint Louis All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
Page 10 GR2000 Installation Guide THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. MARTIN BIRGMEIER Copyright © 1993 Martin Birgmeier. All rights reserved. You may redistribute unmodified or modified versions of this source code provided that the above copyright notice and this and the following conditions are retained.
Page 11 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
Page 12 GR2000 Installation Guide 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
Page 13 You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. [less] Copyright © 1984,1985,1989,1994,1995,1996 Mark Nudelman All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1.
Page 14 GR2000 Installation Guide THIS SOFTWARE IS PROVIDED “AS IS” AND WITHOUT ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR A PARTICULAR PURPOSE. Copyright © 1990, 1991, 1993, 1994 John Robert LoVerso. All rights reserved. Redistribution and use in source and binary forms are permitted provided that the above copyright notice and this paragraph are duplicated in all such forms and that any documentation, advertising materials, and other materials related to such...
Page 15 THIS SOFTWARE IS PROVIDED “AS IS” AND WITHOUT ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. [zlib] Copyright notice: © 1995-1996 Jean-loup Gailly and Mark Adler This software is provided “as-is”, without any express or implied warranty. In no event will the authors be held liable for any damages arising from the use of this software.
Page 16 GR2000 Installation Guide 4. The names “Apache Server” and “Apache Group” must not be used to endorse or promote products derived from this software without prior written permission. For written permission, please contact apache@apache.org. 5. Products derived from this software may not be called “Apache” nor may “Apache” appear in their names without prior written permission of the Apache Group.
Page 17 Permission to use, copy, modify, and distribute this software and its documentation in source and binary forms for lawful purposes and without fee is hereby granted, provided that the above copyright notice appear in all copies and that both the copyright notice and this permission notice appear in supporting documentation, and that any documentation, advertising materials, and other materials related to such distribution and use acknowledge that the software was developed by the...
Page 18 GR2000 Installation Guide 3. LICENSEE may copy the Program and may sublicense others to use object code copies of the Program or any derivative version of the Program. All copies must contain all copyright and other proprietary notices found in the Program as provided by STANFORD.
Page 19 IN NO EVENT SHALL USC, OR ANY OTHER CONTRIBUTOR BE LIABLE FOR ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES, WHETHER IN CONTRACT, TORT, OR OTHER FORM OF ACTION, ARISING OUT OF OR IN CONNECTION WITH, THE USE OR PERFORMANCE OF THIS SOFTWARE. Other copyrights might apply to parts of this software and are so noted when applicable.
Page 20 GR2000 Installation Guide Abbreviations ATM Adaptation Layer Available Bit Rate ACKnowledge Authority and Format Indicator Alarm Indication Signal ANSI American National Standards Institute Automatic Protection Switching Address Resolution Protocol Autonomous System Asynchronous Transfer Mode BECN Backward Explicit Congestion Notification Border Gateway Protocol BGP4 Border Gateway Protocol 4 BGP4+...
Page 21 FECN Forward Explicit Congestion Notification FERF Far End Receive Failure Frame Relay Guaranteed Frame Rate HDLC High-level Data Link Control Hitachi Network Architecture ICMP Internet Control Message Protocol ICMPv6 Internet Control Message Protocol version 6 Identifier Initial Domain Identifier IEEE Institute of Electrical and Electronics Engineers, Inc.
Page 22 GR2000 Installation Guide Internetwork Packet Exchange ISDN Integrated Services Digital Network International Organization for Standardization Internet Service Provider ITU-T International Telecommunication Union - Telecommunication, Standardization Sector Japanese Domain Identifier Not AcKnowledge Local Area Network LAPB Link Access Procedure Balanced Mode Link Control Protocol Label Distribution Protocol LAN Emulation Client...
Page 23 Network Interface board Network Layer Protocol Non-Return-to-Zero NSAP Network Service Access Point NSSA Not So Stubby Area Network Time Protocol PADding OC-3c Optical Carrier level 3 concatenation OC-12c Optical Carrier level 12 concatenation OC-48c Optical Carrier level 48 concatetenation Operation Administration and Management Optical Network Unit Open Systems Interconnection OSPF...
Page 24 GR2000 Installation Guide Routing Information Protocol RIPng Routing Information Protocol next generation Remote Loop Back Routing Manager RMON Remote Network Monitoring MIB Routing Processor Reverse Path Forwarding ReQuest RSVP Resource Reservation Protocol Source Address Service Access Point Start Delimiter Synchronous Digital Hierarchy SDLC Service Advertising Protocol SD-I...
Page 25 User Network Interface Usage Parameter Control Variable Bit Rate Virtual Channel/Virtual Call Virtual Channel Identifier VLAN Virtual LAN Virtual Path Virtual Path Identifier Virtual Private Network VRRP Virtual Router Redundancy Protocol Wide Area Network Work Station World-Wide Web xDSL x Digital Subscriber Line GR2K-GA-1002 Rev.
Page 26 GR2000 Installation Guide This page left intentionally blank xxvi GR2K-GA-1002 Rev. 6.03...
Page 27: General Safety Guidelines
Safety Guide This document provides safety-related notices for use of the GR2000 Gigabit Router. Read the following Safety Guidelines carefully before using the product and follow them to take full advantage of the GR2000’s features. General Safety Guidelines Perform all operations in accordance with the instructions and procedures as described in the product manuals.
Page 28 GR2000 Installation Guide Specific Warning Instructions WARNING: Failure to follow the instructions in this section could cause bodily injury or death to the user. Do not operate the device if you suspect damage or failure. Do not use the device if there is smoke or an unusual smell coming from the system.
Page 29 This router contains a lithium battery for the real-time clock. Mishandling this battery may cause heat build-up, damage, or in an extreme case, explosion or fire. Do not remove the battery from the device, disassemble it, or expose it to °...
Page 30 GR2000 Installation Guide Other Instructions Cleaning Clean the device only with a clean, dry cloth or use a cloth that has been dampened with water or another pH-neutral liquid and thoroughly wrung out. Do not use volatile organic solutions such as benzene or paint thinner, chemicals, chemically treated cloths or pesticides, which may deform, discolor or damage the device.
Page 31: Table Of Contents
Table of Contents Chapter 1 - General Information ............1-1 1.1 Purpose and Organization of This Manual ..................1-1 1.2 Outline of Installation Process ....................... 1-2 Chapter 2 - Product Overview ..............2-1 2.1 Models............................... 2-1 2.2 Physical Appearance ........................2-2 2.3 Device Configuration ........................2-20 2.4 Device Components........................
Page 32: Routing Processor (Rp)
GR2000 Installation Guide Chapter 3 - Component Details ............. 3-1 3.1 Cabinet (Chassis)..........................3-1 3.2 Module Characteristics ........................3-3 3.3 Basic Control Unit (BCU)......................... 3-4 3.3.1 RM-CPU(2S) ..........................3-4 3.3.2 RMP (2S) ..........................3-5 3.3.3 RM-CPU(4S), RMB-CPU (4S), RM-CPU(HH), RMB-CPU (HH), RM-CPU(MH), RMB-CPU (MH), RM-CPU(LH) and RMB-CPU (LH) ..............
Page 33 3.5.27 NWT3-1C..........................3-61 3.5.28 NWE1-8 ..........................3-63 3.6 Power Supply Unit (POW) ......................3-65 3.6.1 POW-S100S ........................... 3-66 3.6.2 POW-H100H........................... 3-67 3.6.3 POW-HDCH ........................... 3-67 3.6.4 POW-M100H and POW-M100HA ..................3-68 3.6.5 POW-M200H and POW-M200HA ..................3-69 3.6.6 POW-MDCH and POW-MDCHA .................... 3-70 3.6.7 POW-L200H and POW-L200HA ....................
Page 34 GR2000 Installation Guide Chapter 4 - Precautions in Planning Installation ......... 4-1 4.1 Prerequisites ............................ 4-1 4.1.1 Local Setup Console and Remote Operation Terminal ............4-1 4.1.2 Backup Flash Memory Card (MC) .................... 4-6 4.2 Configuration Limits ........................4-7 4.2.1 RP ............................
Page 35 4.2.12.2 IPv6 function restrictions regarding the routing processing mechanism (RP) mounting conditions ........................4-40 4.2.12.3 Minimum Required Memory ..................4-41 4.2.12.4 Number of NDP Entries....................4-42 4.2.12.5 Number of Interfaces....................4-43 4.2.12.6 Maximum Number of Addresses to be Set in Multi-Home .......... 4-43 4.2.12.7 Maximum Number of Tunnel Interfaces to be Set............
Page 36 4.6.1.6 Setting of VP peak cell rate ................... 4-60 4.6.2 Required Settings for ATM Connection with Other Device............. 4-61 4.6.2.1 ATM Connection with Hitachi NP200 and NP220 ............4-61 4.6.2.2 ATM Connection with Hitachi AN1000 ................4-62 4.6.2.3 ATM Connection with Cisco Systems’ Router............... 4-62 4.6.3 Connection to ATM Services ....................
Page 37 4.10.2 Traffic of Periodic RIP and Periodic SAP Packets..............4-74 4.10.2.1 Model Traffic of Periodic RIP Packets................. 4-75 4.10.2.2 Model Traffic of Periodic SAP Packets ............... 4-75 4.10.2.3 Traffic of Periodic RIP and Periodic SAP Packets on Group-Defined Interface..4-75 4.11 Precautions on Bridge Connections ..................
Page 38 GR2000 Installation Guide bis system ..........................4-89 4.15.3 Difference of range of VPN ID values by software version, IP-VPN operation system ..4-89 4.15.4 Difference in IP-VPN of the LSP allocation system for each VPN using software version ... 4-90 4.15.4.1 Versions prior to Ver.
Page 39 6.1.5 Cable ............................6-11 6.2 Handling of Components Subject to Static Electricity ............... 6-11 6.3 Installation of Chassis ........................6-12 6.3.1 General Rules for Installation of Chassis ................6-12 6.3.2 Desktop Installation of Chassis ....................6-13 6.3.3 Floor Installation of Chassis ....................6-14 6.3.3.1 Fixation of Located Router ....................
Page 40 GR2000 Installation Guide Chapter 7 - Starting, Setting Up, and Stopping ........7-1 7.1 Overview of Device Operation ......................7-1 7.2 Starting the Router .......................... 7-2 7.3 Restarting the Router ........................7-2 7.4 Setting Up Initial Configuration ...................... 7-3 7.5 Stopping the Router ........................7-3 Chapter 8 - Adding and Removing Components.........
Page 41 8.5.3.3 Expansion of GBIC......................8-23 8.5.3.4 Removal of GBIC ......................8-24 Chapter 9 - Software Installation and Updates........9-1 9.1 Introduction ............................9-1 9.2 Supplied Media and Equipment Required ..................9-1 GR2K-GA-1002 Rev. 6.03...
Page 42 GR2000 Installation Guide This page left intentionally blank xlii GR2K-GA-1002 Rev. 6.03...
Page 43: List Of Figures
List of Figures Chapter 1 - General Information ............1-1 Outline of Installation ..........................1-2 Chapter 2 - Product Overview ..............2-1 Front View of GR2000-2S (AC Input) ..................... 2-3 Rear View of GR2000-2S (AC Input) ...................... 2-3 Front View of GR2000-4S (AC Input) ..................... 2-3 Rear View of GR2000-4S (AC Input) ......................
Page 44 GR2000 Installation Guide Half-Size Module ............................. 3-3 RM-CPU(2S) Front Panel View ....................... 3-4 RMP Front Panel View ..........................3-5 RM-CPU(4S), RMB-CPU (4S) Front Panel View ..................3-8 RM-CPU(HH) RMB-CPU (HH) Front Panel View..................3-8 RM-CPU(MH) RMB-CPU (MH) or RM-CPU(LH) RMB-CPU (LH) Front Panel View (GR2000-10H/20H) ...........................
Page 45: Chapter 4 - Precautions In Planning Installation
AC Input Unit and DC-DC Power Unit of POW-M100H and POW-M100HA ........3-68 AC Input Unit and DC-DC Power Unit of POW-M200H and POW-M200HA ........3-69 DC Input Unit and DC-DC Power Unit of POW-MDCH and POW-MDCHA ........3-70 AC Input Unit and DC-DC Power Unit of POW-L200H and POW-L200HA ........3-71 DC Input Unit and DC-DC Power Unit of POW-LDCH and POW-LDCHA .........
Page 46: Chapter 5 - Installation Site Conditions
GR2000 Installation Guide Half-Size NIF Installation Examples ....................4-18 Example of No. of multicast group...................... 4-25 MPLS Backbone and Access Circuits ....................4-28 Clock closed-loop prohibition ......................4-56 Conversion from Ethernet Frame to ATM Cells ................. 4-58 Shaping at Overload ..........................4-59 Next_Hop resolution ..........................
Page 47 Desktop Installation for GR2000-2S and GR2000-4 ................6-13 Desktop Installation for GR2000-4S ....................6-13 Desktop Installation for GR2000-6H ....................6-14 GR2000-10H Floor Installation ......................6-14 GR2000-20H Floor Installation ......................6-15 GR2000-10 Floor Installation........................ 6-15 GR2000-20 Floor Installation........................ 6-16 GR2000-10H and GR2000-20H Screw Jack and Caster Positions ............ 6-18 GR2000-10 Screw Jack and Caster Positions ..................
Page 48: Chapter 7 - Starting, Setting Up, And Stopping
GR2000 Installation Guide Unmounting of MC ..........................6-63 Connection of Setup Console......................6-65 Chapter 7 - Starting, Setting Up, and Stopping ........7-1 Sequence of Device Operation ......................7-1 Chapter 8 - Adding and Removing Components......... 8-1 Addition/Removal of Full-Size and Half-Size Modules ................ 8-2 Addition/Removal of Full-Size and Half-Size Dummy Panels .............
Page 49: List Of Tables
List of Tables Chapter 1 - General Information ............1-1 Chapter 2 - Product Overview ..............2-1 Maximum Number of Device Components on Enhanced Models ........... 2-28 Each cabinet and maximum number of modules that can be mounted Device Cabinet ....2-29 Abbreviation for BCU model names and configuration of each device .........
Page 50 GR2000 Installation Guide Connector Specifications for NWVX-8, Pin Assignment for V.24............ 3-30 Connector Specifications for NWVX-8, Pin Assignment for X.21............ 3-31 Connector Specifications for NWVX-8, Pin Assignment for V.35............ 3-31 NWJB-8 switch and function of LED indications ................3-32 Connector Specifications for NWJB-8 ....................3-32 NWJ1-4U switch and function of LED indications ................
Page 51 NWT3-1C switch and function of LED indication................3-62 Connector specifications for NWT3-1C ..................... 3-62 NEW1-8 switch and function of LED indications ................3-63 NEW1-8 switch and function of LED indication ................3-64 Connector Specification for NWE1-8 ....................3-64 POW Models ............................3-65 Locations for Components of POW-M100H and POW-M100HA ............
Page 52 GR2000 Installation Guide Accommodation Conditions in the Same RP and Different NIF ............4-19 Accommodation Conditions in the Same NIF and Different LineF ..........4-19 Accommodation Conditions in the Same Line.................. 4-19 Maximum Number of VLANs....................... 4-20 Accommodating conditions for NAOC12-2M and NAOC12-2S............4-20 Accommodating conditions when using the service category GFR for ATM ........
Page 53 Setting the subscribing conditions and configuration defining information of the device ..4-53 Configuration Definition on GR2000 for POS in Multivendor Environment ........4-56 NWJ1-8U connection restrictions....................... 4-57 ATM Configuration Definition Settings Required with NP200 and NP220 ........4-61 ATM Configuration Definition Settings Required with AN1000 ............4-62 ATM Configuration Definition Settings Required with AN1000 ............
Page 54 GR2000 Installation Guide This page left intentionally blank GR2K-GA-1002 Rev. 6.03...
Page 55: Chapter 1 - General Information
Chapter 1 states the purpose and organization of the manual and outlines the installation process. Chapter 2 provides an overview of the GR2000 series. Chapter 3 gives software and hardware details. Chapter 4 gives preparation and planning precautions for installation.
Page 56: Outline Of Installation
GR2000 Installation Guide Outline of Installation Process Figure 1-1 outlines the installation process. Start Installation planning. • Determine target configuration and necessary components of the product (Chapter 2 and Chapter 3). • Ensure precautions in planning installation of the product (Chapter 4). •...
Page 57: Chapter 2 - Product Overview
Chapter 2 Product Overview Models The GR2000 provides eight models. Models GR2000-2S, GR2000-4S, GR2000-6H, and GR2000-10H are new, enhanced models. The following are descriptions of each model: GR2000-2S, has two interface slots. It is the entry model for enterprise and WAN aggregation applications.
Page 58: Front View Of Gr2000-2S (Ac Input)
GR2000 Installation Guide Physical Appearance The following figures show the front and rear views of the GR2000 Gigabit Router Series models. Refer to 2.3 for information about the components in these figures. Figure 2-1: front view of GR2000-2S (AC input) Figure 2-2: rear view of GR2000-2S (AC input) Figure 2-3: front view of GR2000-4S (AC input) Figure 2-4: rear view of GR2000-4S (AC input)
Page 59: Chapter 2 - Product Overview
Product Overview Memory LED (status FAN3 card slot indicator) NIF1 NIF0 RS-232C port (for console) Integrated Ethernet port (10M/100M) x 4 Figure 2-1 Front View of GR2000-2S (AC Input) FAN1 FAN2 FAN4 Power switch RM-CPU with POW Power cord receptacle Figure 2-2 Rear View of GR2000-2S (AC Input) Acrylic Cover Memory card slot...
Page 60: Rear View Of Gr2000-4S
GR2000 Installation Guide RS-232C port (for AUX) RM-CPU POW1 POW0 Power switch Power cord receptacle Figure 2-4 Rear View of GR2000-4S (AC Input) Acrylic Cover RM-CPU1 RM-IO1 RM-CPU0 RM-IO0 RS-232C port (for AUX) NIF1 NIF0 None in case of RMB-CPU NIF3 NIF2 LED (status...
Page 61: Rear View Of Gr2000-6H
Product Overview Power cord receptacle Power switch POW1 POW0 Power cord receptacle Figure 2-6 Rear View of GR2000-6H (AC Input) Placement of RM-IO and NIF boards, and power supply units: INPUT1 (AC) LED (status indicator) Memory card slot INPUT0 (AC) RS-232C connector (for console)
Page 62: Rear View Of Gr2000-10H With Ac Input
GR2000 Installation Guide Placement of RM-CPU and RP boards, and power supply units: DC-DC DC-DC FAN3 DC-DC DC-DC FAN1 RS-232C connector (for AUX) None in Placement of fans in fan tray (top view): case of RMB-CPU (front) (front) (front) (front) Fan 2 Fan 4 Fan 2...
Page 63 Product Overview Placement of RM-CPU and RP boards, and power supply units: DC-DC DC-DC FAN3 DC-DC DC-DC FAN1 RS-232C connector (for AUX) None in Placement of fans in fan tray (top view): case of RMB-CPU (front) (front) (front) (front) Fan 2 Fan 4 Fan 2 Fan 4...
Page 64: Front View Of Gr2000-20H With Ac Input
GR2000 Installation Guide LED (status indicator) Memory card slot RS-232C connector Placement of RM-IO, CSW, and NIF (for console) boards, and power supply units: (CONSOLE & AUX) in case of RMB-10 Terminal block PS INPUT0 (AC) PS INPUT1 (AC) Power breaker Figure 2-11 Front View of GR2000-20H with AC Input GR2K-GA-1002 Rev 6.03...
Page 65: Rear View Of Gr2000-20H With Ac Input
Product Overview Placement of RM-CPU and RP boards, and power supply units: FAN3 FAN1 RS-232C connector (for AUX) None in case of RMB-CPU DC-DC DC-DC DC-DC DC-DC DC-DC DC-DC Placement of fans in fan tray (top view): (front) (front) (front) (front) Fan 2 Fan 4...
Page 66 GR2000 Installation Guide LED (status indicator) Memory card slot RS-232C connector (for console) Placement of RM-IO, CSW, andNIF boards, and power supply units: (CONSOLE & AUX) in case of RMB-10 Terminal block PS INPUT0 (DC) PS INPUT1 (DC) Power breaker Figure 2-13 Front View of GR2000-20H with DC Input 2-10 GR2K-GA-1002...
Page 67 Product Overview Placement of RM-CPU and RP boards, and power supply units: FAN3 FAN1 RS-232C connector (for AUX) None in case of RMB-CPU DC-DC DC-DC DC-DC DC-DC DC-DC DC-DC Placement of fans in fan tray (top view): (front) (front) (front) (front) Fan 2 Fan 4...
Page 68 GR2000 Installation Guide Acrylic Cover Memory card slot LED (status indicator) RM-IO NIF3 NIF2 NIF1 NIF0 Figure 2-15 Front View of GR2000-4 (AC Input) RM-CPU POW1 POW0 Power switch Power switch Power cord Power cord receptacle receptacle Figure 2-16 Rear View of GR2000-4 (AC Input) 2-12 GR2K-GA-1002 Rev 6.03...
Page 69 Product Overview Placement of RM-IO and NIF boards, and power supply units: RM-IO RM-IO LED (status indicator) Memory card slot Power switch RS-232C connector Power cord AC power cord clamp receptacle Figure 2-17 Front View of GR2000-10 with AC Input Placement of RM-CPU and RP boards: Figure 2-18 Rear View of GR2000-10 with AC Input...
Page 70 GR2000 Installation Guide Placement of RM-IO and NIF boards, and power supply units: RM-IO RM-IO LED (status indicator) Memory card slot Breaker Power cord receptacle RS-232C connector RS-232C connector Figure 2-19 Front View of GR2000-10 with DC Input Placement of RM-CPU and RP boards: Terminal block for receiving DC input...
Page 71 Product Overview CSW board (covered): CSW-1S CSW-1M CSW-0S CSW-0M LED (status indicator) Memory card slot Placement of RM-IO and NIF boards: RS-232C connector Power Switch Power cord receptacle Figure 2-21 Front View of GR2000-20 with AC Input GR2K-GA-1002 2-15 Rev 6.03...
Page 72 GR2000 Installation Guide Placement of RM-CPU and RP boards: Placement of power supply units: Power Power Power Power Unit Unit Unit Unit Figure 2-22 Rear View of GR2000-20 with AC Input 2-16 GR2K-GA-1002 Rev 6.03...
Page 73 Product Overview CSW board (covered): CSW-1S CSW-1M CSW-0S CSW-0M LED (status indicator) Memory card slot Placement of RM-IO and NIF boards: RS-232C connector Figure 2-23 Front View of GR2000-20 with DC Input GR2K-GA-1002 2-17 Rev 6.03...
Page 74 GR2000 Installation Guide Placement of RM-CPU and RP boards: Placement of power supply units: Power Power Power Power Unit Unit Unit Unit Figure 2-24 Rear View of GR2000-20 with DC Input 2-18 GR2K-GA-1002 Rev 6.03...
Page 75 Product Overview Guide rail attached Guide rail detached Figure 2-25 Half-Sized and Full-Sized NIF Modules GR2K-GA-1002 2-19 Rev 6.03...
Page 76: Device Configuration
GR2000 Installation Guide Device Configuration All of the GR2000 models have the same architecture and share common components, including: Routing Manager (RM), Routing Processor (RP), Network Interface Unit (NIF), power supply subsystem (PS), and cabinet. In addition, the mid-range and high-end models (GR2000-6H, GR2000-10H, GR2000-20H) implement a highspeed RM–RP connection by means of the Crossbar Switch (CSW).
Page 77: Block Diagram Of Gr2000-2S
Product Overview RMP (RM + RP) Built-in 10M/100M Ethernet (4 ports) Figure 2-26 Block Diagram of GR2000-2S Option for redundant configuration Figure 2-27 Block Diagram of GR2000-4S Option for redundant configuration Figure 2-28 Block Diagram of GR2000-6H, GR2000-10H and GR2000-20H GR2K-GA-1002 2-21 Rev 6.03...
Page 78 GR2000 Installation Guide GR2000-2S The GR2000-2S incorporates one BCU with one 10M/100M Ethernet (4 ports), and one POW. The BCU consists of one RMP (equivalent of RM and RP) physically packaged in one RM-CPU module and one RMP module with one 10M/ 100M Ethernet (4 ports).
Page 79 Product Overview Memory card slot RS-232C port (for console) LED (status indicator) Mounting position of RMP-IO, RP and NIF board. RM-IO NIF3 NIF2 NIF1 NIF0 Figure 2-31 Front View of GR2000-4S RS-232C port (for AUX) Mounting position of RM-CPU board and power supply unit (device integrated type) RM-CPU...
Page 80 GR2000 Installation Guide Acrylic Cover RM-CPU1 RM-IO1 RM-CPU0 RM-IO0 RS-232C port (for AUX) NIF1 NIF0 NIF3 NIF2 LED (status indicator) NIF5 NIF4 Memory card slot RS-232C port (for console) The RP.NIF number starts from 0.1 on the upper tier, being different from 4S.
Page 81 Product Overview For the device configuration when PS is mounted with a DC input unit, and the PS mounting position, please refer to the "Hardware operation manual". Slot for the RM-10 NIF board AC input unit mounting position. INPUT1 (AC) LED (status indicator) Memory...
Page 82 GR2000 Installation Guide GR2000-20H This model incorporates one BCU, one RP, and three POWs; the BCU consists of one RM physically packaged in one RM-CPU module and one RM-IO module, and one CSW physically packaged in one master CSW module (CSW-M) and one sub CSW module (CSW-S).
Page 83 Product Overview FAN1 FAN3 Mounting position of RM-CPU and RP board: RS-232C connector (for AUX) DC-DC power supply unit x 6 Placement of fans in fan tray (top view): (front) (front) (front) (front) Fan 2 Fan 4 Fan 2 Fan 4 FAN2 (power) (main)
Page 84: Maximum Number Of Device Components On Enhanced Models
GR2000 Installation Guide Device Components Table 2-1 and Table 2-3 show the maximum number of device components described in this section, depending on the target GR2000 model. Table 2-1 Maximum Number of Device Components on Enhanced Models Device Component GR2000-2S GR2000-4S GR2000-6H GR2000-10H GR2000-20H Power Supply Unit (POW) Additional POW (POWA) Basic Control Unit (BCU)
Page 85: Each Cabinet And Maximum Number Of Modules That Can Be Mounted Device Cabinet
Product Overview 2.4.1 Cabinet (Network Processor Unit Chassis) Each model of the GR2000 family has its own cabinet that includes one or more fans for cooling. See Figures 2-1 thru 2-24 in 2.2 for their external images. Table 2-2 Each cabinet and maximum number of modules that can be mounted Device Cabinet Maximum number of Device...
Page 86: Rm-Cpu
GR2000 Installation Guide Table 2-3 Abbreviation for BCU model names and configuration of each device Abbreviation for Device cabinet Configuration BCU model name GR2000-10H BCU-M300H • RM-CPU (MH) board • RM-IO (H) board (Built in 6x6 cross bar switch) BCU-M850H •...
Page 87: Crossbar Switch (Csw)
Product Overview 2.4.2.5 Crossbar Switch (CSW) The CSW provides highspeed packet transfer between the RM and the RP on the models of GR2000-6H, GR2000-10H and GR2000-20H. On GR2000-6H, the CSW is included in the RM-CPU board. Its 3-by-3 crossbar switch performs highspeed packet transfer between RM and up to 3 RPs. On GR2000-10H, the CSW is included in the RM-CPU board.
Page 88: Rpa1
GR2000 Installation Guide Table 2-4 RP Specifications RP name Specification Note RP-A1 Backup, QoS/Diff-serv, and multicasting GR2000-2S: Not Packet transfer rate: Approx. 1M packets/s mountable MS = 32MB (standard) - 96MB (max) RP-DV RP-DV is a routing processor to which the label stack H/W transfer function has GR2000-4S,2S: been enhanced.
Page 89 Product Overview Table 2-4 RP Specifications RP name Specification Note RP-D6 GR2000 IPv6 compatible GR2000-2S: Not Has RP-D function mountable IPv6, IPv4 dual stack Packet transfer rate: 1.0Mpps (IPv4) (Full duplex)0.8Mpps (IPv6) MS = 128MB (standard) - 256MB (max) • Packet transfer engine is used commonly for transmission and reception.
Page 90: Network Interface Module (Nif)
GR2000 Installation Guide 2.4.4 Network Interface Module (NIF) The NIF provides Layer 1 and Layer 2 support for various WAN and LAN interfaces. The NIF includes half-size and full-size boards. See Table 2-5 for a list of NIF modules. Table 2-5 List of NIF Modules Type Module Name Interface...
Page 91 SONET/SDH OC-12c/STM-4 (600M) ATM 2 ports (mulimode fiber) full NAOC12-2S** SONET/SDH OC-12c/STM-4 (600M) ATM 2 ports (sigle-mode fiber) full * These interfaces are for use in Japan only. ** Product intended for the Japanese market handled only by Hitachi Japan. GR2K-GA-1002 2-35 Rev 6.03...
Page 92: Ps Model Name For Each Device
GR2000 Installation Guide 2.4.5 Power Supply Unit (POW) The POW receives externally-sourced input power and generates stable direct voltage current (5V, 3.3V, 12V, and 24V) for the router. For input power, GR2000-2S and GR2000-4S can receive 100 or 200 VAC (50/60 Hz); GR2000-6H and GR2000-10H can receive 100 or 200 VAC (50/60 Hz), or –48 or –60 VDC if DC input power option is installed;...
Page 93: Gbic Type
Product Overview 2.4.9 Interface Cables Only leased interface cables for V.24/V.35/X.21 of serial channel are available. NIF shares the same connector as V.24/V.35/X.21, but the cable differs depending on the type of interface. Except for those above mentioned, all interface cables must be procured by the customer.
Page 94: Software
GR2000 Installation Guide Table 2-9 The temperature surveillance threshold value for RMB-CPU and RMB-IO board Temperature Threshold value Significance threshold name value Caution for low Board temperature is lower than the operation guarantee temperature (caution) temperature for this device. Caution for high Board temperature is higher than the operation guarantee temperature (caution) temperature for this device.
Page 95: Routing Software Block Diagram
Product Overview Device Route control processing MPLS/IP-VPN, Browser SNMP LDP, CR-LPD (GateD) Interface Agent (Note 1) (httpd) RIP, OSPF, BGP, RIPng, BGP4+ (Note 2) (Unicast) Bridge Command group (CLI) Application Processing IGMP, Process DVMRP, PIM group ping, telnet, ftp, boot, log, (Multicast) show route, show ospf, Processing...
Page 96: Connections
GR2000 Installation Guide Connections 2.5.1 Interface Cables and Connectors Most interface cables are customer responsibilities. Prepare appropriate interface cables with connectors, according to Table 2-10. Further explanation follows. Table 2-10 Specifications of Interface Cables and Connectors Physical Interface NIF Name Cable Specifications/Notes Length (m) Connector...
Page 97 Product Overview Table 2-10 Specifications of Interface Cables and Connectors (continued) Physical Interface NIF Name Cable Specifications/Notes Length (m) Connector Min. Max. X.21 NWVX-4 Special cable, 5 m standard Device: 50-pin half-pitch, Channel: 15-pin D-sub Basic (I.430, NWJB-8*, UTP category 3/4/5, 4, 8-core, RJ-45 I.430-a) NWMX1-4**...
Page 98 GR2000 Installation Guide Table 2-10 Specifications of Interface Cables and Connectors (continued) 25Mbps ATM NA25M-1* UTP category 3/4/5, 4-core/8-core, 2-pair RJ-45 straight OC-12c/STM-4 NAOC12-2M** Multimode optical fiber of 50/125 or 62.5/ SC 2-core/1-core (ATM)MMF 125 m cre/clad OC-12c/STM-4 NAOC12-2S** Single-mode optical fiber of 10/125 m 1.5k SC 2-core/1-core (ATM)SMF...
Page 99 Product Overview 2.5.1.2 Only special interface cables for V.24/V.35/X.21 of the serial channel are supplied by the manufacturer. NIF modules share the same connector with V.24/V.35/X.21. Other interface cables are to be procured by the customer. V.24 50-pin half-pitch 25-pin D-sub Device Special cable V.35...
Page 100: Network Connections
GR2000 Installation Guide OC-3c/STM-1 (150M) POS, OC-12c/STM-4 (600M) POS MMF SC 2-core/1-core SC 2-core/1-core Device Multimode optical fiber OC-3c/STM-1 (150M) POS, OC-12c/STM-4 (600M) POS, OC-48c/STM-16 (2.4G) POS SMF SC 2-core/1-core SC 2-core/1-core Device Single-mode optical fiber 2.5.1.3 Illustrated below are the ATM interface cables and connectors. All these interface cables are to be procured by the customer.
Page 101: Wan Connection
Product Overview 2.5.2.2 WAN Connection The following WAN connections are possible: Leased line connection Connects to a leased line via modem. Device Leased Line Device M Modem Highspeed digital line connection Connects to a highspeed digital leased line via DSU. Device Highspeed Digital Line Device...
Page 102 GR2000 Installation Guide This page left intentionally blank 2-46 GR2K-GA-1002 Rev 6.03...
Page 103: Installed Dimensions, Masses, And Minimum Service Clearances
Chapter 3 Component Details Cabinet (Chassis) Table 3-1 shows the installed dimensions and the mass of each GR2000 cabinet model. The mass assumes the case when each cabinet model is installed with full options (maximum configuration). This table also refers to the minimum service clearance for maintaining or installing each cabinet model, differentiated by the type of installation (e.g., desktop, floor, and rack-mount).
Page 104: Minimum Service Clearance For Desktop Or Floor Installation
GR2000 Installation Guide 1000 Front Device 1000 Device* 1000 Front 1000 Front Device * Partial projection due to DC input option can be neglected. Figure 3-1 Minimum Service Clearance for Desktop or Floor Installation 1000 Back Rack Pront 1000 Figure 3-2 Minimum Service Clearance for Rack-Mount Installation (Top View) GR2K-GA-1002 Rev.
Page 105: Chapter 3 - Component Details
Component Details Module Characteristics The BCU, RP, and NIF modules come in half-size, full-size, and special-size boards. See the figures below for the appearance of the half-size and full-size boards. Note that the connectors, display, etc. in the enclosure are different for each module. See Section 3.3, “Basic Control Unit (BCU), Section 3.4, “Routing Processor (RP) and Section 3.5, “Network Interface Module (NIF) for more detail on these modules.
Page 106: Bcu Components
GR2000 Installation Guide Basic Control Unit (BCU) The BCU comprises the modules listed in Table 3-2. Description of each board follows. Table 3-2 BCU Components Device Name BCU Model Name Subcomponent Board Name Board Size GR2000-2S – RM-CPU(2S) Special size Full-size, 30mm-wide GR2000-4S BCU-S300S...
Page 107: Chapter 3 - Component Details
Component Details 3.3.2 RMP (2S) The RMP is for GR2000-2S and physically appears as Figure 3-6. The RMP has one CONSOLE (RS232C) port and four 10BASE-T/100BASE-TX ports. Table 3-4 and Table 3-5 show the connector specifications on these ports. # $ /100BASE-TX LNK/ACT :G LINE ERR :Y...
Page 108: Rmp Switch And Function Of Led Indications
GR2000 Installation Guide Switch and LED indication Table 3-3 RMP switch and function of LED indications Name of switch Switch or LED Status Content and LED STATUS (RM) LED: Green/ Shows the Green: Operable operation Yellow/ Red operating Yellow: Blocked condition of RM.
Page 109: Specifications Of 9-Pin D-Sub Connector On Console (Rs232C) Port
Component Details Table 3-3 RMP switch and function of LED indications Name of switch Switch or LED Status Content and LED LINE ERR LED: Yellow Yellow: Line section II/W fault detection. LED: Green Shows the Conditions of transmission and reception signals. operating condition of each line.
Page 110: Rm-Cpu(4S), Rmb-Cpu (4S) Front Panel View
GR2000 Installation Guide 3.3.3 RM-CPU(4S), RMB-CPU (4S), RM-CPU(HH), RMB-CPU (HH), RM-CPU(MH), RMB-CPU (MH), RM-CPU(LH) and RMB-CPU (LH) The RM-CPU(4S) and RMB-CPU (4S) for GR2000-4S, the RM-CPU(HH) and RMB-CPU (HH) for GR2000-6H, the RM-CPU(MH) and RMB-CPU (MH) for GR2000-10H, and the RM-CPU(LH) and RMB-CPU (LH) for GR2000-20H physically appear as Figure 3-7 through Figure 3-9.
Page 111: Rm-Cpu Switch And Function Of Led Indications
Component Details Switch and LED indication Table 3-6 RM-CPU switch and function of LED indications Name of switch Switch or LED Status Content and LED STATUS LED: Green/ Shows the Green: Operable operation Yellow/ Red operating Yellow : Blocking and the board replaceable state. condition of RM.
Page 112: Rm-Cpu(S), Rm-Cpu(M), Rm-Cpu(Mc2) And Rm-Cpu(L)
GR2000 Installation Guide 3.3.4 RM-CPU(S), RM-CPU(M), RM-CPU(MC2) and RM-CPU(L) The RM-CPU(S) for GR2000-4, the RM-CPU(M) for GR2000-10, and the RM-CPU(L) for GR2000-20 physically appear as Figure 3-10 and Figure 3-11. Figure 3-10 RM-CPU(S) Front Panel View Figure 3-11 RM-CPU(M), RM-CPU(MC2) and RM-CPU(L) Front Panel View 3-10 GR2K-GA-1002 Rev.
Page 113: Rm-Io(4S), Rmb-Io (4S) And Rm-Io(H)
Component Details 3.3.5 RM-IO(4S), RMB-IO (4S) and RM-IO(H) The RM-IO(4S) for GR2000-4S, the RMB-IO (4S) for GR2000-4S (BCU-S850S) and the RM-IO(H) for GR2000-6H, GR2000-10H, and GR2000-20H physically appear as Figure 3-12 and Figure 3-14. The RM-IO(4S), RMB-IO (4S) and the RM-IO(H) each have one CONSOLE (RS232C) port and one CONSOLE (10BASE-T/100BASE-TX) port.
Page 114: Rm-Io Switch And Function Of Led Indications
GR2000 Installation Guide Switch and LED indication Table 3-8 RM-IO switch and function of LED indications Name of switch Switch or LED Status Content and LED STATUS LED: Green/ Shows the Green: Operable operation Yellow/ Red operating Yellow: Blocking and cock insertion and removal possible. condition of RM.
Page 115: Specifications Of 9-Pin D-Sub Connector On Console (Rs232C) Port
Component Details Table 3-8 RM-IO switch and function of LED indications Name of switch Switch or LED Status Content and LED ACCESS 1 LED: Green Shows the state of Blinking: MC card one being accessed. (Memory card MC card being take-out is prohibited.) one.
Page 116: Rm-Io(S), Rm-Io(M), And Rm-Io(L)
GR2000 Installation Guide Table 3-10 Specifications of 8-pin RJ45 Connector on CONSOLE (10BASE-T/ 100BASE-TX) Port Pin No. Specifications Transmit (+) (TA) Transmit (-) (TB) Receive (+) (RA) Receive (-) (RB) 3.3.6 RM-IO(S), RM-IO(M), and RM-IO(L) The RM-IO(S) for GR2000-4, the RM-IO(M) for GR2000-10, and the RM-IO(L) for GR2000-20 physically appear as Figure 3-12 and Figure 3-14.
Page 117: Bcu Switch And Function Of Led Indications
Component Details 3.3.7 RMB-IO(H) The RMB-IO(H) for GR2000-6H, GR2000-10H and GR2000-20H (BCU-H850H, BCU-M850H and BCU-L850H) physically appears as Figure 3-17 4 & 1 & # % % & + # & 2 4 + 4 # % % 2 4 + 4 Figure 3-17 RMB-IO(H) Front Panel View 3.3.8...
Page 118: Bcu Switch And Function Of Led Indications
GR2000 Installation Guide Routing Processor (RP) Three types of RP models, RP-A1 (standard), and RP-C/C6 and RP-D/D6 (options for highspeed media), apply to the GR2000 device models as listed in Table 3-12. Each RP model comprises one RP board. Description of each RP board follows. Table 3-12 RP Models RP Model Name Board Size...
Page 119: Nam
Component Details 3.4.2 RP-C/RP-C6 The RP-C and RP-C6physically appear as Figure 3-21. The switch, LED display functions of the RP-C and RP-C6 are the same as those of the RP-A1. The additional LEDs are for test purposes only. " "...
Page 120: Nif Models
GR2000 Installation Guide Network Interface Module (NIF) Various types of NIF models are provided as listed in Table 3-15. Each NIF model comprises one NIF board. Description of each NIF board follows. Table 3-15 NIF Models Category Physical Interface NIF Name Board Size Remarks 10BASE-T,...
Page 121: Ne100-8T, Ne100-8Ta And Ne100-8Tb Front Panel View
NAOC3-8S** Full size, 30mm wide 15km *For Japan only ** Product intended for the Japanese market handled only by Hitachi Japan. 3.5.1 NE100-8T, NE100-8TA and NE100-8TB The NE100-8T, NE100-8TA, and NE100-8TB physically appear as Figure 3-22. These NIFs each have eight ports for connection with 8-pin modular connectors of RJ-45.
Page 122: Ne100-4F, Ne100-4Fs, And Ne100-4Fs4 Front Panel View
GR2000 Installation Guide 3.5.2 NE100-4F, NE100-4FS, and NE100-4FS4 The NE100-4F, NE100-4FS, and NE100-4FS4 physically appear as Figure 3-23. These NIFs each have four ports for connection with pairs of SC 2-core optical fiber connectors (transmit and receive). Table 3-18 shows the connector specifications. 100BASE-FX LINE ERR LINK...
Page 123: Ne1G-1S, Ne1G-1Sa, Ne1G-1L, Ne1G-1La, Ne1G-1Lha, Ne1G-1Lha8, Ne1G-1Sb, Ne1G-1Lb And Ne1G-1Lhba Front Panel View
Component Details 3.5.3 NE1G-1S, NE1G-1SA, NE1G-1L, NE1G-1LA, NE1G-1LHA, NE1G-1LHA8, NE1G-1LB, NE1G-1SB and NE1G-1LHBA The NE1G-1S, NE1G-1SA, NE1G-1L, NE1G-1LA, NE1G-1LHA, NE1G-1LHA8, NE1G-1LB, NE1G-1SB and NE1G-1LHBA physically appear as Figure 3-24. These NIFs each have one port for connection with a pair of SC 2-core optical fiber connectors (transmit and receive).
Page 124: Connector Specifications For Ne1G-1S, Ne1G-1Sa, Ne1G-1L, Ne1G-1La, Ne1G-1Lha, Ne1G-1Lha8, Ne1G-1Sb, Ne1G-1Lb And Ne1G-1Lhba
GR2000 Installation Guide Table 3-20 Connector Specifications for NE1G-1S, NE1G-1SA, NE1G-1L, NE1G-1LA, NE1G-1LHA, NE1G-1LHA8, NE1G-1SB, NE1G-1LB and NE1G-1LHBA Connector Specifications NE1G-1S, NE1G-1SA, SC 2-core (flat) connector (multimode fiber, 850 nm wavelength) NE1G-1SB NE1G-1L, NE1G-1LA, SC 2-core (flat) connector (multimode/single-mode fiber, 1300 nm wavelength) NE1G-1LB NE1G-1LHA, SC 2-core (flat) connector (multimode/single-mode fiber, 1500 nm wavelength)
Page 125 Component Details Table 3-22 NWVX-4 LINE LED indication LINE State as seen by Line state indication Line state Detail of state (*1) (*1) SXMP in MMI and browser (*1) (*3) Being initialized. Being initialized (3). initialize (*3) Being operated In normal operation. In standby (3).
Page 126 GR2000 Installation Guide Connector Specifications for NWVX-4, Pin Assignment for X.21 Table 3-24 WAN 15-pin (Male) Connection Router 50-Pin Specifications ————— I(A) (indication) (input) ————— I(B) ————— 26 R(A) (receive) (input) ————— 28 R(B) ————— 34 (signal ground) ————— 50 S(A) (signal element timing) (input) —————...
Page 127: Nwvx-8
Component Details 3.5.5 NWVX-8 The NWVX-8 physically appears as Figure 3-26. L I N E 7 L I N E 3 Y : L I N E E R R V . 2 4 / V . 3 5 / X . 2 1 G : A C T .
Page 128: New1-8 Switch And Function Of Led Indication
GR2000 Installation Guide Table 3-27 NEW1-8 switch and function of LED indication Line state indication in LINE ERR LOOP Line state Detail of state State as seen by SXMP MMI and (*1) (*1) browser (*3) Being initialized. Being initialized (3). initialize (*3) Being operated...
Page 129: Relationship Between Connection Of Cables Supplied With Vx-8 And Line Number
Component Details Be careful when connecting the cables attached to VX-8 to the devices that the connector insertion faces are reversed between the lower side connectors (LINE 0, LINE 1, and LINE 4, LINE 5) and the upper side connectors (LINE 2, LINE 3, and LINE 6, LINE 7).
Page 130: Line Numbers For The Cables Attached To Nwvx-8
GR2000 Installation Guide Line numbers for the cables attached to VX-8 Be careful when connecting the cables attached to VX-8 to the devices that the connector insertion faces are reversed between the lower side connectors (LINE 0, LINE 1, and LINE 4, LINE 5) and the upper side connectors (LINE 2, LINE 3, and LINE 6, LINE 7).
Page 131 of cable length according to line speed" described in Section 5: Precautions. The cables attached to VX- GR2000 Modem connecting cable to 8 are required when Cable for DCE be prepared by the client. NWVX-8 is used. DCE side DCE side WS/PC, etc.
Page 132 LINE 0 to 7 (50-pin half-pitch connectors) on the tips of the conversion cables are the connectors to connect V.24/X.21/V.35, which require dedicated cables to match each interface. Specification of the pins including the cable is shown below (the same as that for NWVX-4U). Connector Specifications for NWVX-8, Pin Assignment for V.24 Table 3-28 WAN 25-pin (Male) Connection Router 50-pin...
Page 133 WAN 15-pin (Male) Connection Router 50-Pin Specifications ————— I(A) (indication) (input) ————— I(B) ————— 26 R(A) (receive) (input) ————— 28 R(B) ————— 34 (signal ground) ————— 50 S(A) (signal element timing) (input) ————— 48 S(B) ————— C(A) (control) (output) ————— C(B) —————...
Page 134: Nwjb-8
The NWJB-8 physically appears as Figure 3-32. This NIF has eight ports for connection with 8-pin modular connectors of RJ-45 in compliance with IS8877. Table 3-32 shows the connector specifications. ISDN/HSD(I) 64k/128kbps (JAPAN) ACT:G LINE ERR:Y LINE 7 LINE 6 LINE 5 LINE 4 LINE 3...
Page 135: Nwj1-4U
The NWJ1-4U physically appears as Figure 3-33. This NIF has four ports for connection with 8-pin modular connectors of RJ-45 in compliance with IS8877. Table 3-34 shows the connector specifications. ISDN/HSD 1.5Mbps UNCHANNELIZED (JAPAN) LINE ERR ACTIVE LINE 3 LINE 0 LINE 2 LINE 1 Figure 3-33 NWJ1-4U Front Panel View...
Page 136: Nwmx1-4
The NWMX1-4 physically appears as Figure 3-34. This NIF has four ports for connection with 8-pin modular connectors of RJ-45 in compliance with IS8877. Table 3-36 shows the connector specifications. ISDN/HSD(I)64k/128k(JAPAN) ISDN/HSD 1.5Mbps (JAPAN) LINE ERR LINE 3 LINE 2 LINE 1 LINE 0 Figure 3-34 NWMX1-4 Front Panel View...
Page 137: Nwj1-8U
The NWJ1-8U physically appear as Figure 3-35. ISDN/HSD 1.5Mbps(JAPAN) ACT:G LINE ERR:Y LINE 3 LINE 7 LINE 2 LINE 6 LINE 5 LINE 4 LINE 1 LINE 0 Figure 3-35 NWJ1-8U Front Panel View Switch and LED indication Table 3-37 NWJ1-8U switch and function of LED indications...
Page 138: Nwt1-4
The NWT1-4 physically appears as Figure 3-36. This NIF has four ports for connection with 8-pin modular connectors of RJ-48. Table 3-38 shows the connector specifications. T1 1.5Mbps LINK T/R LOOP LINE 3 LINE 2 LINE 1 LINE 0 Figure 3-36 NWT1-4 Front Panel View Switch and LED indication Table 3-39 NWT1-4 switch and function of LED indications Name...
Page 139 Line state LINE State as seen by LOOP Line state Detail of state indication in MMI (*1) (*1) (*1) (*1) (*1) SXMP and browser (*3) Being Being initialized (3). initialize initialized. (*3) Being In normal In standby (3). active up operated operation.
Page 140: Nwe1-4
The NWE1-4 physically appears as Figure 3-37. This NIF has four ports for connection with 8-pin modular connectors of RJ-48. Table 3-44 shows the connector specifications. E1 2Mbps LINK LOOP LINE 0 LINE 3 LINE 2 LINE 1 Figure 3-37 NWE1-4 Front Panel View Switch and LED indication Table 3-42 NWE1-4 switch and function of LED indications Name...
Page 141 Line state LINE State as seen by LOOP Line state Detail of state indication in MMI (*1) (*1) (*1) (*1) (*1) SXMP and browser (*3) Being Being initialized (3). initialize initialized. (*3) Being In normal In standby (3). active up operated operation.
Page 142: Nwj2-1U
The NWJ2-1U physically appears as Figure 3-38. This NIF has one port for connection with a pair of BNC connectors (receive and transmit). Table 3-47 shows the connector specifications. HSD 6.3Mbps UNCHANNELIZED (JAPAN) LINE ERR LINE 0 Figure 3-38 NWJ2-1U Front Panel View Switch and LED indication Table 3-45 NW2J-1U switch and function of LED indications Name...
Page 143 LINE Line state State as seen by Line state Detail of state indication in M (*1) (*1) (*1) (*1) (*1) SXMP (*1) and browse (*3) Being Being initialized (3). initialize initialized. (*3) Being In normal In standby (3). active up operated operation.
Page 144: Nwt3-2U
The NWT3-2U physically appears as Figure 3-39. This NIF has two ports for connection with pairs of BNC connectors (receive and transmit). Table 3-50 shows the connector specifications. UNCHANNELIZED T3 45Mbps LINE ERR LOOP LINE 1 LINE 0 Figure 3-39 NWT3-2U Front Panel View Switch and LED indication Table 3-48 NWT3-2U switch and function of LED indications Name...
Page 145 LINE Line state State as seen by LOOP Line state Detail of state indication in M (*1) (*1) (*1) (*1) (*1) SXMP (*1) and browse (*3) Being Being initialized (3). initialize initialized. (*3) Being In normal In standby (3). active up operated operation.
Page 146: Nwe3-2U
The NWE3-2U physically appears as Figure 3-40. This NIF has two ports for connection with pairs of BNC connectors (receive and transmit). Table 3-53 shows the connector specifications. UNCHANNELIZED E3 34Mbps LINE ERR LOOP LINE 1 LINE 0 Figure 3-40 NWE3-2U Front Panel View Switch and LED indication Table 3-51 NWE3-2U switch and function of LED indications Name...
Page 147 LINE Line state State as seen by LOOP Line state Detail of state indication in M (*1) (*1) (*1) (*1) (*1) SXMP (*1) and browse (*3) Being Being initialized (3). initialize initialized. (*3) Being In normal In standby (3). active up operated operation.
Page 148: Nwe3-1C
The NWE3-1C physically appear as Figure 3-41. CHANNELIZED E3 34Mbps LINE ERR LOOP LINE 0 Figure 3-41 NWE3-1C Front Panel View Switch and LED indication Table 3-54 NWE3-1C switch and function of LED indications Name LED: Color Status Content STATUS LED: Green/ Shows the operating Green: Operable operation...
Page 149 LINE Line state State as seen by LOOP Line state Detail of state indication in M (*1) (*1) (*1) (*1) (*1) SXMP (*1) and browse (*3) Being Being initialized (3). initialize initialized. (*3) Being In normal In standby (3). active up operated operation.
Page 150: Nwoc3C-2M, Nwoc3C-2S, Nwoc3C-2Sd And Nwoc3C-2Md Front Panel View
The NWOC3C-2M, NWOC3C-2S, NWOC3C-2SD and NWOC3C-2MD physically appear as Figure 3-42. These NIFs each have two ports for connection with pairs of SC 2-core optical fiber connectors (transmit and receive). Table 3-59 shows the connector specifications. POS OC-3C/STM-1 LINE ERR LINK LINE 1 LINE 0...
Page 151 function of LED indication LINE Line state LINK State as seen by Line state Detail of state indication in M (*1) (*1) (*1) (*1) (*1) SXMP (*1) and browse (*3) (*3) Being Being initialized (3). initialize initialized. (*3) (*3) (*4) Being In normal In standby (3).
Page 152: Nwoc3C-8S And Nwoc3C-8M Front Panel View
The NWOC3C-8S and NWOC3C-8M physically appear as Figure 3-43. NW OC3C-8M POS OC-3C/STM-1 LINE7 LINE5 LINE4 LINE6 LINE3 LINE0 LINE1 LINE2 Figure 3-43 NWOC3C-8S and NWOC3C-8M Front Panel View Switch and LED indication Table 3-60 NWOC3C-8S/NWOC3C-8M switch and function of LED indications Name LED: Color Status...
Page 153: Nwoc12C-1S And Nwoc12-1Sd Front Panel View
The NWOC12C-1S and NWOC12-1SD physically appears as Figure 3-44. This NIF has one port for connection with a pair of SC 2-core optical fiber connectors (recei and transmit). Table 3-63 shows the connector specifications. NWOV12-1SD POS OC-12C/STM-4 LINE ERR LINK LINE 0(A) Figure 3-44 NWOC12C-1S and NWOC12-1SD Front Panel View Switch and LED indication...
Page 154: Nwoc12-4S And Nwoc12-4M Front Panel View
The NWOC12-4S and NWOC12-4M physically appear as Figure 3-45. NW OC12-4M POS OC-12C/STM-4 LINE 3 LINE 2 LINE 1 LINE 0 Figure 3-45 NWOC12-4S and NWOC12-4M Front Panel View Switch and LED indication Table 3-64 NWOC12-4S/NWOC12-4M switch and function of LED indications Name LED: Color Status...
Page 155: Nwoc48-1S, Nwoc48-1S4 And Nwoc48-1S8 Front Panel View
The NWOC48-1S, NWOC48-1S4, and NWOC48-1S8 physically appear as Figure 3-46. These NIFs each have one port for connection with a pair of SC 2-core optica fiber connectors (transmit and receive). Table 3-67 shows the connector specifications. 0 9 1 % 5 0 9 1 % 5 2 1 5 1 % % 5 6 / # 2 5...
Page 156: Nwoc48-1A, Nwoc48-1A4 And Nwoc48-1A8
Connector Specifications NWOC48-1S SC 2-core (flat) connector (single-mode fiber) NWOC48-1S4 SC 2-core (flat) connector (single-mode fiber) NWOC48-1S8 SC 2-core (flat) connector (single-mode fiber) 3.5.21 NWOC48-1A, NWOC48-1A4 and NWOC48-1A8 The NWOC48-1A, NWOC48-1A4 and NWOC48-1A8 physically appear as Figure 3-47. NW OC48-1A8 NW O C48-1A4 POS OC-48C/STM-16 LINE 1...
Page 157 indication Status Green Yellow Extinguished No APS APS steady Working being selected state Protection being selected Working being selected switching Protection being selected over Lamp tested Table 3-70 Connector Specifications for NWOC48-1A, NWOC48-1A4 and NWOC48-1A Connector Specifications NWOC48-1A SC 2-core (flat) connector (singlemode fiber) NWOC48-1A4 SC 2-core (flat) connector (singlemode fiber) NWOC48-1A8...
Page 158: Naoc3-1M And Naoc3-1S Front Panel View
The NAOC3-1M and NAOC3-1S physically appear as Figure 3-48. These NIFs each have one port for connection with a pair of SC 2-core optical fiber connectors (transmit and receive). Table 3-72 shows the connector specifications. Or ATM OC-3/STM-1(SMF) NAOC3-1S ATM OC-3/STM-1(MMF) LINE ERR LINE 0 Figure 3-48 NAOC3-1M and NAOC3-1S Front Panel View...
Page 159: Na25M-1
The NA25M-1 physically appears as Figure 3-49. This NIF has one port for connection with an 8-pin modular connector of RJ-45. Table 3-74 shows the connector specifications. LINE ERR LINE0 Figure 3-49 NA25M-1 Front Panel View Switch and LED indication Table 3-73 NWOC3-1S/NWOC3-1M switch and function of LED indications Name LED: Color...
Page 160: Naoc3-8S And Naoc3-8M Front Panel View
The NAOC3-8S and NAOC3-8M physically appear as Figure 3-42 M ark *** in p arenthese s ind ica tes M M F or S M F . M ark * at the end N A O C 3 -8M : M M F ind ica tes M or S .
Page 161: Naoc12-2S And Naoc12-2M Front Panel View
The NAOC12-2S and NAOC12-2M physically appear as Figure 3-51. NAOC12-2 ATM OC-12/STM-4(MMF) ATM OC-12/STM- LINE1 LINE0 Figure 3-51 NAOC12-2S and NAOC12-2M Front Panel View Switch and LED indication Table 3-77 NWOC12-2S/NWOC12-2M switch and function of LED indications Name LED: Color Status Content STATUS...
Page 162: Ne1G-4C
The NE1G-4C physically appears as Figure 3-52. ) $ + % $ # 5 ' : 5 + ) & 6 . + 0 ' ' 4 4 # % 6 . + 0 - . + 0 ' .
Page 163: Nwt3-1C
The NWT3-1C physically appears as Figure 3-53. % * # 0 0 ' . + < ' & 6 / D R U . + 0 ' ' 4 4 . 1 1 2 # % 6 .
Page 164 LINE Line state State as seen by LOOP Line state Detail of state indication in MMI (*1) (*1) (*1) (*1) (*1) SXMP (*1) and browser (*3) Being Being initialized (3). initialize initialized. (*3) Being In normal In standby (3). active up operated operation.
Page 165: Nwe1-8
The NWE1-8 physically appears as Figure 3-54. # % 6 ) 6 4 ) ' / D R U . + 0 ' ' 4 4 ; . 1 1 2 ; . + 0 ' .
Page 166 Line state indication in LINE ERR LOOP Line state Detail of state State as seen by SXMP MMI and (*1) (*1) browser (*3) Being initialized. Being initialized (3). initialize (*3) Being operated In normal In standby (3). active up operation. (*3) Line fault being In operation (line fault being...
Page 167 Various types of POW models apply to the GR2000 device models as listed in Table 3-87. Additional information on each POW model follows. Table 3-87 POW Models Model Name Components Application Device Model Power Supply Configuration Q’ POW-S100S • One power unit GR2000-4S Single 100 or 200 VAC input •...
Page 168: Pow-S100S
Device Model Power Supply Configuration Q’ty POW-S100 • One power unit GR2000-4 Single 100 or 200 VAC input • One power cord Dual 100 or 200 VAC input POW-M100 • One power unit GR2000-10 Single 100 or 200 VAC input •...
Page 169: Power Unit Of Pow-H100H
Figure 3-56 illustrates the power unit of the POW-H100H. The dimensions are approximate (in mm), and the drawing is not to scale. Figure 3-56 Power Unit of POW-H100H 3.6.3 POW-HDCH Figure 3-57 illustrates the power unit of the POW-HDCH. The dimensions are approximate (in mm), and the drawing is not to scale.
Page 170 The POW-M100H comprises one AC input unit (SWR4820-U), one power cord, and three DC-DC power units (two DC38001-Us for 3.3V/24V dc output and one DC46003-U for 3.3V/5V dc output). The POW-M100HA comprises one AC input unit (SWR4820-U), one power cord, and one DC-DC power unit (DC46003-U). Figure 3-58 illustrates the AC input unit and (one of) the DC-DC power unit(s) of the POW-M100H and the POW-M100HA.
Page 171 The POW-M200H comprises one AC input unit (SWR4825-U), one power cord, and three DC-DC power units (two DC38001-Us for 3.3V/24V dc output and one DC46003-U for 3.3V/5V dc output). The POW-M200HA comprises one AC input un (SWR4825-U), one power cord, and one DC-DC power unit (DC46003-U). Figure 3-59 illustrates the AC input unit and (one of) the DC-DC power unit(s) of th POW-M200H and the POW-M200HA.
Page 172 The POW-MDCH comprises one DC input unit (IN140-6U) and three DC-DC power units (two DC38001-Us for 3.3V/24V dc output and one DC46003-U for 3.3V/5V dc output). The POW-MDCHA comprises one DC input unit (IN140-6U) and one DC-DC power unit (DC46003-U). Figure 3-60 illustrates the DC input unit and (one of) the DC-DC power unit(s) of the POW-MDCH and the POW-MDCHA.
Page 173 The POW-L200H comprises one input pannel (IN120-2FU), one AC input unit (SWR4845-U), one input power cord, and five DC-DC power units (two DC03R375-U for 3.3V dc output, two DC38001-Us for 3.3V/24V dc output, and one DC46003-U for 3.3V/5V dc output). The POW-L200HA comprises one input pannel (IN120-2FU one AC input unit (SWR4845-U), one input power cord, and one DC-DC power un (DC46003-U).
Page 174 The POW-LDCH comprises one DC input unit (IN150-6U) and five DC-DC power units (two DC03R375-Us for 3.3V dc output, two DC38001-Us for 3.3V/24V dc output, and one DC46003-U for 3.3V/5V dc output). The POW-LDCHA comprises one DC input unit (IN150-6U) and one DC-DC power unit (DC46003-U). Figure 3-62 illustrates the DC input unit and (one of) the DC-DC power unit(s) of the POW-LDCH and the POW-LDCHA.
Page 175: Pow-S100
Figure 3-63 illustrates the power unit of the POW-S100. The dimensions are approximate (in mm), and the drawing is not to scale. Figure 3-63 Power Unit of POW-S100 3.6.10 POW-M100 and POW-L200 Figure 3-64 illustrates the power unit of the POW-M100 and the POW-L200. The dimensions are approximate (in mm), and the drawing is not to scale.
Page 176 Figure 3-65 illustrates the DC power unit of the POW-MDC and the POW-LDC. The dimensions are approximate (in mm), and the drawing is not to scale.
Page 177: Fittings
Figure 3-67 commonly illustrates the MC30, a 30-M-byte memory card module, an the MC64, a 64-M-byte memory card module. The dimensions are in mm and the drawing is not to scale. Part Name Figure 3-67 MC30 and MC64 Flash Memory Card Module Fittings...
Page 178: Wan Loop Connector
A loop connector for the WAN line is suppled by each router model. Figure 3-69 shows this WAN Loop Connector. 50-Pin Half-Pitch Connector Figure 3-69 WAN Loop Connector 3.9.3 V.24, V.35, and X.21 Interface Cables These interface cables are supplied as fittings, while the other interface cables are the customer responsibilities.
Page 179: V.24 Interface Cable
The appearance of the V.24 interface cable is as shown in Figure 3-71. Figure 3-72 shows the cable specifications. When connecting to a TA or modem on the V.24 interface, an HN-F9355-71H cabl (5m), its option for 1m to 16m (request for price quotation basis), or an HN-F9355-71F cable (3m) is applicable.
Page 180 Supported or not. Physical Line speed range Restrictions on Corresponding cable model interface (Xkbit/s) cable length NWVX-4 NWVX-8 V.24 2.4 < X < 9.6 16 m or less HN-F9355-71F, HN-F9355-71H, (Note 1) 9.6 < X < 19.2 16 m or less HN-F9355-71F, HN-F9355-71H, (Note 1) 19.2 <...
Page 181 NWVX-8 is supplied with the cables attached to VX-8. Connect the cables attached to VX-8 (100-pin high-density connector) as show below. The tips of the cables attached to VX-8 have connecting sections for the same 50-pin half-pitch connectors (LINE 0 to LINE 7) as in NWVX-4. Be careful when connecting the cables attached to VX-8 to the devices that the connector insertion faces are reversed between the lower side connectors (LINE 0, LINE 1, and LINE 4, LINE 5) and the upper side connectors (LINE 2, LINE 3, and...
Page 182 Be careful when connecting the cables attached to VX-8 to the devices that the connector insertion faces are reversed between the lower side connectors (LINE 0, LINE 1, and LINE 4, LINE 5) and the upper side connectors (LINE 2, LINE 3, and LINE 6, LINE 7). LINE#7 LINE#6 LINE#5...
Page 183 The cables attached to VX- GR2000 Modem connecting cable to 8 are required when Cable for DCE be prepared by the client. NWVX-8 is used. DCE side DCE side WS/PC, etc. GR2000 Connection of connector to connector. Supplied cable = 1m is not included Cable length = X m.
Page 184 shows the cable specifications. When connecting to a TA or modem on the V.35 interface, an HN-F9355-72H cable (5m) or its option for 1m to 16m (request for price quotation basis) is applicable. The latter is required when the line speed is 6 Mbps. As illustrated, the other-end connector has a skirt for protection of pin bends.
Page 185 shows the cable specifications. When connecting to a TA or modem on the X.21 interface, an HN-F9355-73H cab (5m) or its option for 1m to 16m (request for price quotation basis) is applicable. T latter is required when the line speed is 6 Mbps. When using the own router as a DCE and connecting to a DTE-attached cable on X.21 interface, an HN-F9355-77H cable (5m) is applicable.
Page 186: Customer-Responsibility Interface Cables
This section provides detailed specifications and recommended products for the customer-responsibility interface cables. For the V.24/V.35/X.21 cables provided as fittings, see Subsection 3.9.3. Note: For direct connection between the router and the other end device, make sure of the connector type on the other end device which may require a different cable.
Page 187: Lan Interface Cables
All the LAN interface cables are customer responsibilities. Depending on the type LAN and the distance as shown in Figure 3-82 and Table 3-95, an appropriate LA interface cable needs to be procured. LAN setup (boundary with network) Router NE100-8T/ NE100-8TA NE100-8TB NE100-4F...
Page 188 (CAT 5) cable is required. A UTP Category 3 (CAT 3) cable is applicable when connecting only to the 10BASE-T port at 10 Mbps. Figure 3-83 shows the cable specifications. Table 3-96 Pin arrangement on the device side (10MBASE/100MBASE interface) Pin No.
Page 189 an optical fiber cable with the specifications shown in Figure 3-84. One or more cables of the same type is recommended to be prepared for spare. Table 3-98 sho the router’s optical interface specifications for 100BASE-FX multimode connectio 2-core SC 2-core SC connector connector...
Page 190 requires an optical fiber cable with the specifications shown in Figure 3-85. One or more cables of the same type is recommended to be prepared for spare. Table 3-99 shows the router’s optical interface specifications for 100BASE-FX and 1000BASE-LH single-mode connections. 2-core SC 2-core SC connector...
Page 191: Wan Interface Cables
The WAN interface cables except those supplied as fittings (V.24, V.35, and X.21 cables) are customer responsibilities. Depending on the type of WAN and the distance as shown in Figure 3-86 and Table 3-100, an appropriate WAN interface cable needs to be procured. Boundary with network Router Customer setup...
Page 192 Connection Length (m) Approx. Q’ty/ Interface Cable Type Width (mm) From Min. Max. Basic (I.430, Router Modular – 1–8 I.430-a) rosette Primary (I.431, Router Modular – 1–4 I.431-a) rosette/ Primary (T1/E1) Router DSU – 1800 1–4 Secondary Router DSU – Metal (coaxial) (G.703) Tertiary (T3/E3)
Page 193 Pin No. Specifications Unused Unused Transmit (+) Receive (+) Receive (+) Transmit (-) Unused Unused Note: Because of being a twisted pair cable, make pairs of (A) and (a), and (B) and (b) using the ab pin assignment. For pins other than these, do not care about the pairing, either unconnected or connected can be accepted.
Page 194: Utp Cable For Primary (I.431 Or I.431-A)
Modular rosette Modular rosette Device without without terminator with terminator terminator Flat metal cable (4-wire) Note: This connection requires costs for extra connection work and modular rosette in addition to those for ordinary cabling and DSU setup. For details of the connection work, consult the carrier (e.g., NTT) . Figure 3-89 Connection to Device without Terminator 3.10.2.2 UTP Cable for Primary (I.431 or I.431-a)
Page 195 Customer setup length L1 (with one modular rosette) Flat metal cable (4-wire) Primary (1.431) interface outer Customer setup length L2 (cable with modulars on both ends) Figure 3-91 Sample Indirect Connection with Primary (I.431 or I.431-a) Configuration Notes: • Customer setup length L1, i.e., the total length of flat metal cables, should not exceed 16 m - L2. addition, be sure to use the flat metal cable with the core diameter of 0.65 mm.
Page 196: Metal (Coaxial) Cable For Secondary (G.703)
Pin No. Function (device side) Function (DSU side) Unused Transmit (+) Unused Transmit (-) Transmit (+) Unused Receive (+) Receive (+) Receive (+) Receive (+) Transmit (-) Unused Unused Unused Unused Unused Note: Because of the cable being a twist pair cable, make pairs of (A) with (a), and (B) with (b) in the above pin assignment.
Page 197: Multimode Optical Fiber Cable For Oc-3C/Stm-1 (Pos) Mmf
Jacket Inner conductor Shield 1 Shield 2 Insulator Figure 3-95 Construction of duel shield type coaxial cable 3.10.2.6 Multimode Optical Fiber Cable for OC-3c/STM-1 (POS) MMF Multimode connection with the OC-3c/STM-1 (POS) MMF interface requires an optical fiber cable with the specifications shown in Figure 3-96. One or more cab of the same type is recommended to be prepared for spare.
Page 198: Single-Mode Optical Fiber Cable
1 dB/km (max. 15 km) connector connector Recommended model name: Hitachi Optical Fiber Cable SM1005-2F-C2SC-[ ]M (cord length in brackets) Boundary with network: router’s connector Figure 3-97 Single-Mode Optical Fiber Cable Specifications for OC-3c/STM-1 (POS) SMF and OC-12c/STM-4 (POS)
Page 199 0.3 dB/km (max. 2 km or 40 km) connector connector Recommended model name: Hitachi Optical Fiber Cable SM1005-2M-C2SC-[ ]M (cord length in brackets) Boundary with network: router’s connector Figure 3-98 Single-Mode Optical Fiber Cable Specifications for OC-48c/STM-16 (POS Table 3-104 Optical Interface Specifications for OC-48c/STM-16 (POS) Single-Mode...
Page 200 Rec om m ended m odel nam e: Hitachi O ptic al F iber Cable C-2DS F 0803(2)(D )#S /P /0. 2# [ ] M : 2-c ore SC connector – 2-core S C connector. (core length in brack ets )
Page 201: Atm Interface Cables
All the ATM interface cables are customer responsibilities. Depending on the type ATM and the distance as shown in Figure 3-100 and Table 3-106, an appropriate ATM interface cable needs to be procured. ATM setup (boundary with network) Router Device/ NAOC3-1M DSU/ONU NAOC3-1M...
Page 202 optical fiber cable. Figure 3-94 shows the cable specifications, which are the same as those for the OC-3c/STM-1 (POS) MMF interface (Subsection 3.10.2.6). One or more cables of the same type is recommended to be prepared for spare. The boundary with ATM (OC3) is used as a connector on this router’s side. A multimode optical fiber is used for connection with the router.
Page 203 optical fiber cable with the specifications shown in Figure 3-102. One or more cab of the same type is recommended to be prepared for spare. The boundary with ATM (OC3) is used as a connector on this router’s side. A multimode optical fiber is used for connection with the router. Figure 3-102 sho the schematic diagram.
Page 204 Figure 3-103 shows the cable specifications. 8-pole modular 8-pole modular connector (RJ-45) connector (RJ-45) UTP category 3/4/5, 4-core/8-core, 2-pair straight Recommended model name: Hitachi UTP Cable C5E-PCTA-P8/P8-[ ]M (cord length in brackets) Boundary with network: router’s connector Figure 3-103 UTP Cable Specifications for 25Mbps ATM...
Page 205: Local Setup Console And Remote Operation Terminal
Precautions in Planning Installatio Prerequisites 4.1.1 Local Setup Console and Remote Operation Terminal Figure 4-1 illustrates the local setup console and remote operation terminals to b procured by the user. Description of each type follows. Console...
Page 206 For the operation thereafter, a console or a remote operation terminal is required. The console shall use a terminal connected to RS232C, and the remote operation terminal shall use a terminal connected via IP network to remotely log in with this device by using telnet or rlogin, or log-in connected through the web browser.
Page 207 9-pin on Router Side Connection 9-pin on Setup Console Side Pin Number Signal Name Pin Number Signal Name Note 3: In order to connect the RM serial interface of this device with a modem, use a straight cable to conn the AT interchangeable machine and the modem.
Page 208 reception received automatically. Setting when reset The setting is read out from the non-volatile memory in AT&Y0 the modem. Saving the setting The setting is saved in the non-volatile memory in the AT&W0 modem. Note 5: Perform dialing by using the dial function of the terminal software. For the dial setting, refer to the operation manual for the terminal software.
Page 209 SNMP Manager HP OpenView Network Node Manager Ver4.0x (HP-UX version) HP OpenView Network Node Manager Ver5.01 (HP-UX version) HITACHI NETM*Cm2 Ver04-0x (HI-UX and HP-UX versions, Japan on HITACHI NETM*Cm2 Ver05-00 (HP-UX and WindowsNT versions, Jap...
Page 210 line speed is slow. A case of too many number of the connected IP network or connected interface. For example, a case where the number of interface of the device is too many, or a case where retrieval of the IP related MIB information takes excessive amount of time.
Page 211: Configuration Limits
Within the maximum configuration defined in Section 2.4, “Device Components,” GR2000 has certain configuration limits as described below. 4.2.1 Three types of RPs, RP-A1, RP-C and RP-D apply to specific GR2000 models as shown in Table 4-6. RP mounting conditions RP mounting conditions by each model RP mounting conditions by each model are shown in Table 9-2: The RP mounting conditions by each model.
Page 212 Mounting number of Mounting number of Mounting number of Model RP-A1 RP-C, RP-C6 whole RP GR2000-10H (100V AC input) 5 or less 5 or less 4 or less 5 or less 3 or less 5 or less GR2000-20H (100V AC input) 10 or less 10 or less 9 or less...
Page 213 NIFs apply to specific RP types and specific GR2000 models as shown in Table 4- Table 4-7 Quantities of NIFs by Router Model NIF Type Application to RP Type* Max. Q’ty per Router Model RP-D, RP-C, RP-D6 and Inter- Board RP-C6 and RP-DV face...
Page 214 NWOC12-1SD NWOC12-4S NWOC48-1S NWOC48-1S4 NWOC48-1S8 NWOC48-1A NWOC48-1A4 NWOC48-1A8 Full NAOC12-2M NAOC12-2S NAOC3-8M NAOC3-8S Half NAOC3-1M NAOC3-1S NA25M-1 When an NIF is installed with not applicable RP type, a log message is output and the NIF’s initial setup is not activated. **Also assumes its equivalent integrated in GR2000-2S, if applicable, as RP-A1.
Page 215 GR2000-4H, GR2000-10H, GR2000-6H GR2000-20H BCU-S300S BCU-S850S Increment unit GR2000-2S BCU-H300H BCU-H850H BCU-M300H BCU-M850H BCU-L300H BCU-L850H Base 64MB 128M 256MB Add One MS64 128MB Add One MS128 256MB Add Two MS128s and 256MB Remove Base (64MB)* Removed base memory of BCU can be utilized for RP memory increment. Table 4-9 RP Memory Increment by RP Type Resulting Memory Capacity MB...
Page 216 4-11. Table 4-11 100BASE-FX Line Accommodation Router Model Max. No. of Lines Per NIF Per RP Per Router GR2000-2S GR2000-4S GR2000-6H GR2000-10H GR2000-20H 4.2.4.3 Line Accommodation with WAN (Other than ISDN and Overload) The circuit accommodation conditions indicated below apply to WAN circuits of 6Mbit/s or less and 34Mbit/s E3 multiplex circuits (other than ISDN).
Page 217 Condition Max. Throughput kbps per Use of WAN Protocol on Subject RP Disabled When only PPP is used (non-multiplex) 32,500 When only PPP is used (multiplex) 26,000 When only frame relay is used 25,900 When PPP and frame relay are used 25,900 Enabled without When only PPP is used...
Page 218 Table 4-17 WAN (ISDN) Line Accommodation Limit Condition: QoS Max. Throughput kbps per RP* Must be disabled 12,288 * Calculations are based on 128-byte packets. 4.2.4.5 Line Accommodation with WAN (Overload) Line accommodation with WAN (overload) is limited as shown in Table 4-18. For the multilink protocol type, the line accommodation varies with the overload configurations illustrated in Figure 4-2, and the resulting accommodations are shown in Table 4-19 through Table 4-22.
Page 219 Number of Links per Bundle Throughput (pps) No. of Bundles per RP (128-byte Convers 1,384 1,128 Note: An overhead of 12 bytes is to be added to each link. Table 4-20 Multilink Overload Line Accommodation Limit: Inter-RP, Half Duplex, 64kbps Bundled Number of Links per Bundle Throughput (pps) No.
Page 220 connected using the same bus. Accommodate in the range where the total of each line speed does not exceed 600M bits/s. NIF1 is not restricted by a bus and each NIF can be accommodated to the maximum. The shared-bus structure of GR2000-2S is shown in Figure 4-3.
Page 221 and GR2000-4. On these router models, NIF0 and NIF2 connect with each other v bus, and NIF1 and NIF3 connect with each other via the other bus. The aggregat line speed of NIF0 and NIF2, and that of NIF1 and NIF3, must not exceed 600 Mb Figure 5-19 illustrates this shared-bus structure.
Page 222 = 100 Mbps 150Mbps x 1 NEOC3-2S NE100-8T = 150Mbps 10BASE-T x 6 = 60 Mbps Not usable Not usable NIF0: NIF0: 100BASE-TX x 4 100BASE-TX x 4 NE100-8T NE100-8T = 400 Mbps = 400 Mbps 10BASE-T x 4 10BASE-T x 4 = 40 Mbps = 40 Mbps Example A...
Page 223 Table 4-25 shows the accommodation conditions in the same RP in Ethernet. Table 4-26 shows the accommodation conditions in the same NIF, and Table 4-27 shows those in the same line. Functions that can be operated by Ethernet are as follows: VRRP, MPLS, Tag-VLAN(IPv4) (Note1), Tag-VLAN(IPv6) (Note1), bridge protoco multihome, IP protocol, IPv6 protocol, IPX protocol, IPv4 multicast, IPv6 multicast, and non- Tag-VLAN.
Page 224 Item Per router Per RP Per line VLAN In case of BCU-300H, BCU-N300H, and BCU-L300H: 256 In case of BCU-850H, BCU-M850H, and BCU-L850H: 256Å~RP 4.2.4.9 Line accommodating conditions for ATM Accommodating conditions for OC-12c/STM-4 ATM NAOC12-2M and NAOC12-2S can accommodate two lines, but for the total speed value, follow the accommodating conditions described below.
Page 225 Shown here is the maximum number of peers that can be connected to GR2000 through LAN, frame relay, or ATM network. The peer includes not only routers bu also terminals. 4.2.5.1 Maximum Number of ARP Entries In the LAN, frame relay, or ATM network, the hardware address corresponding to destination address of the packet is determined by the address resolution protoc such as ARP and InverseARP.
Page 226 Maximum Number of VCs Router Model Per Line Per NIF Per Interface Per RP Per Router GR2000-2S 2,048 2,048 4,096 4,096 GR2000-4S 2,048 2,048 4,096 4,096 GR2000-6H 2,048 2,048 4,096 4,096 GR2000-10H 2,048 2,048 4,096 4,096 GR2000-20H 2,048 2,048 4,096 4,096 4.2.6 Maximum Number of Interfaces and Multihome Subnets...
Page 227 4.2.7.1 Maximum Number of Neighbor Routers Definition of the maximum number of neighbor routers varies with routing protoc as shown below. Table 4-36 shows the maximum number of neighbor routers ba on the definition by each routing protocol. For static routing, the number of next hop addresses. For RIP, the number of interfaces on which RIP operates.
Page 228 Routing No. of Higher Installed Max. No. of Route Max. No. of Neighbor Peers*** Protocol Peers* Memory Entries** Multipath Not Used Multipath Used BGP4 256MB 120,000 512MB 120,000 160,000 768MB 120,000 160,000 512MB 120,000 160,000 768MB 120,000 160,000 512MB 120,000 768MB 120,000 160,000...
Page 229 The number of interfaces and routing table entries capable of defining IP multica are shown in Table 4-40. This device supports PIM-DM, PIM-SM and DVMRP as multicast routing protocols. Also, the PIM-DM and DVMRP protocols do not oper simultaneously. Table 4-40 IP Multicast Accommodation Limits Item Max.
Page 230 Table 4-41 and Table 4-42 show the IPX and Bridge accommodation limits. Table 4-41 IPX Accommodation Limits Router Model Max. No. of Static Max No. of IPX Interfaces Max. No. of Routing ARP Entries Table Entries Per RP Per Router GR2000-6H 256/device 1,000...
Page 231 maximum number of dynamic entries and static entries. Use the device so that t total value of dynamic and static entries does not exceed the maximum number o entries for the device. Using the device at the maximum entry capacity requires mounted memory amount shown in "(3) Minimum required memory".
Page 232 up the MPLS network must be RP-D, RP-DV or RP-C, RP-CV. RP-A and RP-A1 will not operate. In addition, in regard to the conditions of NIFs that support MPLS functions, NIF conditions that accommodate MPLS backbone circuits are shown in Table 4-47 and NIF conditions that accommodate MPLS access circuits are shown in Table 4-51 Refer to Figure 4-7 for the location of MPLS backbone and access circuits.
Page 233 MPLS Support (*1) Category NIF Name Backbone circuit Access circuit NE100-8TA D, DV NE1G-1LA D, DV NE1G-1SA D, DV NE1G-1LHA D, DV NE1G-1LHA8 D, DV NE100-8TB D, DV NE1G-1LB D, DV NE1G-1SB D, DV NE1G-1LHBA D, DV NE100-4F/4FS/4FS4 D, DV NE1G-4C C, CV NWVX-4...
Page 234 NAOC3-8M C, CV NAOC3-8S C, CV NAOC12-2M C, CV NAOC12-2S C, CV (*1) Supported x: Not supported (*2) Only PPP is supported. FR is not supported. Only clear channel is supported. (*3) In the LDP (DU) mode, the ATM lines are outside the object of support for the backbone line. 4.2.11.3 Memory Card Unit (MC) When using MPLS functions, MC card must be MC64 and MC30 will not operate.
Page 235 IPv4 unicast Path entry count BCU memory No. of ATM V size per NIF Maximum number of entries by protocols RIP+OSPF BGP4 (Note 2) Statics 128MB or more 2,000 or less 2,000 500 or less 256 or les 256MB or more 22,000 or less 2,000 20,000...
Page 236 Routing Min. band MPLS protocol processor IPv4 unicast IPv4 multicast ATM VC count guarantee with mode module (RP) path entry count path entry count per NIF kbit/s memory designated LDP (DU) Mode 64MB or more 2,000 or less unused 256 or less 128MB 125,000 or less unused...
Page 237 IP unicast IP muiticast Maximum path entry count DVMRP Maximum number of entries memory (S,G) (S,G) by protocols Interface Interface size entry entry count count count count Static +OSPF 128MB 10,000 10,000 Unused Unused Unused Unused or more 5,000 5,000 10,000 10,000 10,000...
Page 238 Maximum path entry count DVMRP No. of Maximum number of entries memory ATM VCs (S,G) (S,G) by protocols Interface Interface size per NIF entry entry count count count count Static +OSPF 1,024MB 500,000 30,000 500,000 5,000 or more or less or less (Note 8) 1,000,000...
Page 239 IP multicast path entry count Routing processor IP unicast DVMRP ATM VC static Min. module path entry count per (S,G) entry guara Interface Interface (RP) count (S,G) entry count entry count count count memory count 64MB 10,000 1,000 4096 or more or less or less or less...
Page 240 MPLS protocol Function item Detailed item Support mode Common to both Number of VPNs When any of BCU-H850/ 2,559 as maximum modes. accommodated per BCU-M850H/BCU-L850 are used edge router and software after Ver. 06-03 is used. When BCUs other than those stated 255 as maximum in Item 1 are used or software before Ver.
Page 241 mode VPN ID - Ver. 06-00 : 1-255 Ver. 06-01 - : 1-10,000,000 Not permitted. *1:a < 2,000. a + b + c > 4,000 a: Number of LSPs to be Ingress, b: Number of LSPs to be Core, and c: Number of LSPs to be Egress. *2: Maximum of 255 before Ver.
Page 242 entry number describable when utilizing the MPLS policy routing function. This function requires that the total number of IP filter entries used by all the functions mounted in this device be set so that this value is not exceeded in order to utilize the IP filter table as in the IP policy routing function.
Page 243 conditions when utilizing the COPS function. With the COPS function, the accommodating conditions for the maximum flow entry number and the maximu QoS queue attribute entry number are applied in order to realize the policy set fro policy server by utilizing the QoS control function of the device. Table 4-57 COPS agent accommodating conditions Item Description...
Page 244 IPv6 providing function Accommodated RP condition IPv6 relaying Filter IP tunneling IPv6 multicast RP-A1, S/W processing S/W processing None RM processing None RP-CRP-D RP-C6, RP-D6 H/W processing H/W processing H/W processing RP processing H/W processing (Note: 1) If RP-C6 and RP-D6, and RP-ALRP-C and RP-D are mounted in a mixed way, the IPv6 function can only be used in RP-C6 and RP-D6.
Page 245 IPv4 multicast and the minimum required memory of a basic control module (BC on the number of NDP static entries when an IPv6 function is used are shown in Table 4-61. The minimum required memory of RP is also shown in Table 4-62. Table 4-61 BCU minimum required memory IPv4 unicast IPv4 multi cast...
Page 246 Routing processor IPv6 unicast IPv6 multicast IPv4 unicast IPv4 multicast No. of ATM module (RP) path entry count path entry count path entry count path entry count VCs per NIF memory 32MB or more 25,000 or less 1,000 or less 10,000 or less 1,000 or less 256 or less...
Page 247 interfaces. The maximum number of interfaces in each model whose IPv6 addres can be set is shown in Table 4-64. The value shown in the table is the value obtained when the number of tunnel interfaces is subtracted. Moreover, the operation in the maximum number of interfaces presupposes that router informat is set using a static route.
Page 248 over IPv4 tunnel is shown in Table 4-66. The total number of both tunnel interfaces must be lower than the value shown in Table 4-66 Table 4-66 Number of Tunnel Interfaces Number of interfaces Router Model IPv6 over IPv4 Per Router IPv4 over IPv6 GR2000-2S GR2000-4S...
Page 249 Number of addresses set by configuration definition information Total number of IPv6 settable interface not IPv6 addresses set Number of I Tunnel interface including tunnel interface by configuration addresses se definition router IPv6 link local IPv6 gloval IPv6 link local IPv6 global information address...
Page 250 number of adjacent routers (RIPng), and the maximum number of adjacent peers (BGP4+) is shown in Table 4-70. The maximum number of adjacent routers is the number of routers that advertise a route from this router. The maximum number of adjacent peers is the number of peers that advertise a route from this router.
Page 251 Item Max. device entry count Max. dynamic entry count Max. static entry cou IPv6 unicast path entries 25,000/device 25,000/device 1,000/device NDP entries 1,024/device 1,024/device 1,024/device IPv4 unicast path entries 250,000/device 250,000/device 1,000/device 4,096/RP *1 4,096/RP *1 4,096/RP IPX routing table 1,000/deivce 1,000/deivce 200/deivce...
Page 252 Number of Tag-VLAN Router Model Per RP Per Router GR2000-2S Tag-VLAN cannot be set. GR2000-4S GR2000-6H BCU-H300H BCU-H850H 256 x RP GR2000-10H BCU-M300H BCU-M850H 256 x RP GR2000-20H BCU-L300H BCU-L850H 256 x RP 4.2.13.3 Number of Tag-VLANs to be Set in Multi-Home Like an IP address, Tag-VLAN can be set to the multi-home connection of LAN.
Page 253 conditions when utilizing the COPS function. In the COPS function, the accommodating conditions for the maximum flow entry number and the maximu QoS queue attribute entry are applied in order to realize the policy set from the po server by utilizing the QoS control function of the device. Table 4-76 COPS agent accommodating conditions Item Description...
Page 254 4.3.1 Items to be Prepared Operation terminal Prepare an operation terminal in advance since one is required for the device to execute configuration definitions and operation commands. A CD-ROM drive is required by the terminal for loading the software. Backup use MC The control program of the device, configuration definition data and so forth are stored in the MC.
Page 255 When you connect GR2000 and any other router on Ethernet, pay attention to th restrictions shown below. 4.4.1 10BASE-T/100BASE-TX Match the interface type (10BASE-T or 100BASE-TX) and the full-duplex/ half-duplex mode setting between GR2000’s configuration definition and the oth router’s interface status. Otherwise, connection will fail. 4.4.2 100BASE-FX GR2000 can be defined to operate either in full-duplex fixed mode or in half-dup...
Page 256 This router supports IEEE802.1Q (Tag-VLAN), but it does not support IEEE802.1p (priority control). WAN Networking Restrictions 4.5.1 Required Settings on GR2000 for Connecting Other Devices on PPP Connecting GR2000 to certain devices on PPP sometimes require specific setting of configuration definition options on GR2000 as shown in Table 4-77. For the configuration definition operation, see Subsection 3.7.1 in Configuration Guide.
Page 257 utilizes InverseARP protocol in compliance with RFC1293/RFC2390. Since InverseARP is not a mandatory requirement, certain products may not support it Consequently, there may be cases when the frping command issued from GR2000 ends in a timeout even the target device is in the reachable status. 4.5.2.4 Conditions When Submitting Application Form to Frame Relay Network This information is for Japan only.
Page 258 Filling columns in application form Designation of application Setting the configuration when this defining information of this Remarks Connecting General selection device is device condition alternative connected Protocol operation Terminal (DTE) Select optionally No setting is required because of Used most generally. of PVC state from the three default operation.
Page 259 Filling columns in application form Designation of application Setting the configuration when this defining information of this Remarks Connecting General selection device is device condition alternative connected CLLM message Supported. Select any one Designate the signal reception The CLLM is no item from the monitoring time by using in the protocol...
Page 260 4.5.3.1 Required Setting on GR2000 for POS in Multivendor Environment When you connect GR2000 with other vendor’s router on POS interface, set up the configuration definition on GR2000 according to Table 4-79. Table 4-79 Configuration Definition on GR2000 for POS in Multivendor Environment Definition Item Selectable Options Required Setting...
Page 261 Restrictions applicable to NWJ1-8U circuit multiplex connections When mounting NWJ1-8U in the device and setting the PRI circuit, there are limit the number of circuit interfaces and multiplexed time slots. NWJ1-8U restriction are given in Table 4-80 Table 4-80 NWJ1-8U connection restrictions Line Time slots start Posible Time...
Page 262 4.6.1 Bandwidth Planning Considerations 4.6.1.1 Routing Capacity of GR2000 on ATM Interface The routing capacity of GR2000 on ATM interface is 50 kpps transmission per line. Plan the network so that the traffic exceeding the router’s capacity will not rush into the router.
Page 263 the defined VC bandwidth is exceeded, GR2000 discards the excessive amount o cells as illustrated in Figure 4-10. At this process called shaping, possible loss of l with the other device may result if a dynamic routing protocol such as RIP or OS has been used on the subject interface.
Page 264 the outbound control in units of the ATM service categories (CBR, UBR, etc). Pay attention that the Layer 3 QoS available for the LAN or WAN interface such as protocol-based QoS and IP-address-based QoS does not function on the ATM interface.
Page 265 For the configuration definition operation on GR2000, see Subsection 3. in Configuration Guide. 4.6.2.1 ATM Connection with Hitachi NP200 and NP220 Table 4-81 shows the required settings for the ATM connection with Hitachi NP2 and NP220. Table 4-81 ATM Configuration Definition Settings Required with NP200 and NP220 Connection...
Page 266 Table 4-82 ATM Configuration Definition Settings Required with AN1000 Connection Required Setting on GR2000 Required Setting on Target Device Type Com- Parameter Option Categor Parameter Option mand OC-3c/STM-1 line oc3atm | 25atm oc3atm Line Speed 155 Shap -clock independent Port Clock Source Internal (default)
Page 267 The encapsulation method for IPX packets uses LLC/SNAP in compliance wit RFC1483. 4.6.4.2 ATM Connection with Bridge Devices Ensure that the Bridge device (e.g., bridge-router, bridge, or LAN switch) connect over the ATM network satisfies the following conditions. Hitachi’s multiprotocol routers NP200 and NP220 satisfy these conditions.
Page 268 Interface Address in Point-to-Point Line Connection GR2000 regards the route information in the point-to-point line connection (direct connection) as two host routes. This method is also adopted in Hitachi routers NP220, NP200, and NP150. Accordingly, when a network only consists of these routing devices, you can assign interface addresses to the point-to-point line as follows.
Page 269 When forwarding RIP packets with this device on point-to-point circuits, destinat addresses are sent by unicast addresses (interface address of the other device). I addition, when receiving RIP packets from point-to-point circuits, they are receiv with a unicast address (one’s own interface address or limited broadcast address (address of all 1’s) as the destination address.
Page 270 4.7.8.1 Cautions Regarding NextHop Resolution When advertising paths to the BGP speaker in one and the same AS in this device, one’s own peering address used for peering with the BGP speaker is set in NEXT_HOP attributes. In addition, path data NEXT_HOP attributes received by the device are resolved based on the IGP path.
Page 271 When you replace the existing router (other than GR2000) with this router, pay attention to possible deviation of RIP-1 implementation. For example, the followin routers have different implementations of RIP-1: Hitachi’s NP200, NP150, NP100 NP120C, and Cisco Systems’ routers. When an interface address is further divided into subnets, GR2000 does not crea natural mask route (network route for the subject interface).
Page 272 4.9.1 Connection with IPv6 Router Pay attention to the following when connecting this router and other equipment by IPv6 routing. 4.9.1.1 Interface Address of Point-to-Point Type Line This router handles the path information (direct-coupled path) of a point-to-point type line as two host paths. Therefore, in a network consisting of only this router, the interface addresses below can be allocated to the point-to-point type line.
Page 273 Do not advertise the allocated site local address to the outside. Specify a nexthopself parameter to the configuration definition information of the corresponding peer when sending the received path information to the internal BGP4+ peer using this router. The setting above is required when making connections with a Cisco router.
Page 274 Device Packet to Terminal Terminal A Terminal B Figure 4-14 Configuration to use the device for communication between IPv6 terminals on the same link ICMPv6 re-direct message transmission...
Page 275 the interface is started up. Be careful because, if this action executes the ping6 a traceroute6 commands to the IPv6 address for which duplication has been identi with other devices, a response may be returned from the IPv6 address of another interface in the device, rather than from the IPv6 address designated as the destination.
Page 276 Functional item Detailed item TCP/IP communication IPv6 unicast forwarding function IPv6 unicast routing Static RIPng OSPFv3 BGP4+ Export/Import/Aggregate Packet filtering function (Note 1) Line type 10/100M Ethernet Giga-Bit Ethernet PPP over IPv6 ATM over IPv6 (Note 2) Tunnel function IPv6 over IPv4 configured tunnel (Note 3) IPv6 over IPv6 configured tunnel (Note 3) etwork management SNMP...
Page 277: Configuration Settings
When you use GR2000 as an IPX router, pay attention to the following. 4.10.1 Configuration Settings 4.10.1.1 Setting of RIP Packet Processing By defining the configuration information, you can make GR2000 as an IPX rout operate in one of the following modes for the RIP data packet processing: Dynamic routing only Static routing only Both dynamic routing and static routing...
Page 278 Forward: Does not respond to the watchdog packet on behalf of the client. Choose an option for the above mode setting, taking the billing for the line such as ISDN and the network traffic into consideration. Serialization packet and diagnostic packet GR2000 handles these packets in either “Forward”...
Page 279 calculated by the following formula: n ³ 50 (n: number of RIP entries stored). Example: When n £ 50, 1 packet. When n = 1000 (maximum), 20 packets. 4.10.2.2 Model Traffic of Periodic SAP Packets The number of periodic SAP packets (480 bytes per packet) broadcast at one time calculated by the following formula: n ³...
Page 280 When you use the bridge function of GR2000, pay attention to the following. 4.11.1 Protocol and Topology Restrictions 4.11.1.1 Spanning-Tree Protocol When you use the spanning-tree protocol, ensure that all the bridge-connected routers and bridges are set to use the same level of the spanning-tree protocol (IEEE802.1).
Page 281 where frames are bridge-relayed among specified interfaces. In the event that you add the bridge definition to an existing interface with multiple DLCIs in partial-m or full-mesh network configuration, you must redefine a single interface into mult interfaces each with a single DLCI. Conversely, in the event that you plan a new network where the bridge interface definition is anticipated, you are advised to prepare a network where each interface comprises only one DLCI.
Page 282 When bridge is defined on an interface where multiple VCs are grouped, BPDUs or relay frames not learned are broadcast to all the VCs in the group. Consequently, it is cautioned that an inadvertent addition of bridge definition to an existing grouped interface may cause unnecessary traffic to flow through the interface if the group includes a VC not using protocols other than IP.
Page 283 When you use the QoS function of GR2000, pay attention to the following. 4.12.1 Relationship Between Load on RP and QoS In normal operation, QoS controls queuing and transmitting of packets as illustra in Figure 4-18. In the event of a certain amount of load on the RP, there may be cases when QoS fails and packets are discarded as illustrated in Figure 4-19.
Page 284 RP, NIF Discarding of packets due to heavy load Output queues (packets accumulated) QoS control failing (packets discarded Line regardless of priority)
Page 285 4.13.1 Connection with LAN Switch Pay attention to the following when connecting this router and a LAN switch by Tag-VLAN. 4.13.1.1 VLAN type The only VLAN that this router supports is Tag-VLAN on an IPv4 packet. VLAN se a LAN switch should be one of the following VLANs, even when the LAN switch th connects this router supports VLAN (e.g., protocol VLAN of IPX) other than the Tag-VLAN.
Page 286 [VLAN 1] LAN switch IP configuration definition definition Layer 3 relay LAN switch of this router layer 2 relay ARP (static) configuration definition Network B [VLAN 2] No tag Figure 4-21 Network Configuration...
Page 287 4.14.1 Multicast relay Please pay attention to the following points when relaying a multicast packet usi this router. 4.14.1.1 Common to protocols This router prepares a multicast routing entry for performing multicast communication when the first multicast packet is received. Because the multica packet is relayed by way of using the software until the entry is prepared, a pack may be lost temporarily.
Page 288 In the system configuration allowing mixed use with a device other than this device, multi-cast communication may become impossible due to difference in the calculation range of check sum for PIM-Register message (capsulated packet). If the Register message does not perform multi-cast relaying at the rendezvous point due to a check sum error, change the range to calculate the PIM check sum by using the configuration defining information of this device.
Page 289 Multicast is suitable for single direction communication of 1 (transmitter): N (receiver) in which data are distributed from a server (transmitter) to each group (receiver). Precautions are given below in relation to the network patterns applica to PIM-DM and PIM-SM: 4.14.3.1 PIM-DM PIM-DM can be applied to a tree type network.
Page 290 redundant route exists. Router Server (Transmitter) Host Router Router Host Group 1 (receiver) : Multicast communication route addressed to Group 1 : Multicast data packet flown periodically to Group 1 Inapplicable network pattern...
Page 291 which a redundant route exists. However, please be sufficiently cautious when arranging the rendezvous points. Figure 4-24 shows the applicable PIM-SM network. Tree type network Router Router Server (Transmitter) Router Host Router Router Rendezvous point Host Router Router Group 1 (receiver)
Page 292 Configuration in which a receiver exists between the transmitter and a rendezvous point Relaying via the rendezvous point cannot be performed efficiently if multicast communication is attempted from a server to Group 1 in the following configuration: Server (Transmitter) Rendezvous point Router Router PIM-SM router...
Page 293 PIM-SM router Router Router PIM-SM router Host Router Group 1 (receiver) PIM-SM router 4.15 Precautions for using MPLS 4.15.1 Non-permitted mixed use of LSP allocation system for each VPN and RFC2547 bis system The MPLS/VPN function using the "LDP(DU) mode/RFC2547 bis system" is the...
Page 294: Software Version
VPN ID designating IP-VPN operation syste Range of values in VPN ID method RFC2547 bis system [Ver. 06-03] Numerical designatio 1 to 1,000,000 Name (character string Alphanumerics within 14 letters with head in designation) alphanumeric, or character string using hyphen and underscore LSP allocation system for each Numerical designation...
Page 295 of the LSP can not be transferred, and the restriction on the number of VPNs per MPLS net has been eliminated. Table 4-87 shows the contents of the TLV used. Table 4-87 Contents of the TLV used Field Value U bit F bit Type 0x3E00...
Page 297: Environmental Requirements
Installation Site Condition Environmental Requirements 5.1.1 Temperature and Humidity To guarantee normal operation of the GR2000 router, observe the temperature a humidity specifications of Table 5-1. In daily usage, also observe the following: Do not place the router near a source of heat or a steam. Avoid direct sunlight.
Page 298: Dust
Dust conditions for this router must meet the criteria of Table 5-2 in falling-dust measurement or floating-dust mass density measurement. A sample process of falling-dust measurement is shown in Figure 5-1. When the measured value exceeds the acceptable range, and when the conductor and insulator are heavily covered in dust, appropriate protection, such as shortening of the periodic inspection cycle, addition of a dust-proof case, and air purification are required depending on the humidity of the installation site.
Page 299: External Magnetic Field
To reduce external magnetic field, note the following in facility construction such main power line and air conditioning: Do not cross the distribution panel location for the computer system and the primary side main-line cable construction route in the ceiling of the compute room or on the floor.
Page 300: Flooring
An ordinary office is acceptable for installation of the router; however, if the room where the router is to be installed is to be newly built, flooring with the following qualities is recommended. It is important not to have exposed metal in contact with flooring for safety reasons.
Page 301 Water: When cleaning the floor, do not wet the router. Do not place vases, etc., on the router. Do not let rain wet the router. In an area where flood damage might occur, determine an evacuation meth for the router. Electromagnetic interference: When another high frequency device is used n the router, the router might not operate properly due to interference of electri waves generated by the other device.
Page 302: Input Power Requirements
5.2.1 Input Power Requirements The input power supplied to the GR2000 series models must meet the requirements in Table 5-3 for AC input or those in Table 5-4 for DC input. Table 5-3 Input Power Requirements—AC Input Router Model Input Voltage...
Page 303: Power Feeding Diagram
5.2.2.1 100V ac Input (GR2000-2S, GR2000-4S, GR2000-6H, GR2000-10H, GR2000-4, GR2000- A standard, non-redundant power feeding diagram with 100V ac input is shown Figure 5-3. Figure 5-4 shows its redundant power feeding counterpart, in which c GR2000-2S is not applicable. 100 Vac, single phase, 50/60 Hz NEMA 5-15...
Page 304 A standard, non-redundant power feeding diagram with 200V ac input is shown in Figure 5-5. Figure 5-6 shows its redundant power feeding counterpart, in which case GR2000-2S is not applicable. 200 Vac, single phase, 50/60 Hz NEMA 5-15R (convenience outlet) 100 Vac, single phase, 50/60 Hz...
Page 305 shown in Figure 5-7. Figure 5-8 shows its redundant power feeding counterpart. – 48V or – 60V dc NEMA 5-15R (convenience outlet) 100 Vac, single phase, 50/60 Hz Power distribution panel Ground CB: Circuit breaker Terminal plug (6H/10/10H/20:M5, 20H:M6) for device input power: 1 for non-redundant input...
Page 306 The branch circuit to be installed on the customer’s power distribution panel must be a circuit breaker (CB) in compliance with the requirements in Table 5-5. In addition, follow the guidelines below. Do not connect other electrical devices to this branch circuit. Total load of the branch circuit must be under 80–90 percent of the rating.
Page 307 Depending on the ac supply voltage and ampacity, the receptacle to mate the inp power plug must meet the requirements in Table 5-6. Table 5-6 Receptacle Types for AC Input Nominal Input Receptacle Applicable Connect Voltage (V ac) Router Model Type Face Rating...
Page 308 Electrical noise generated by other devices might cause failure. When you plan the power supply, consider the following to enhance anti-noise capability. Do not connect a foreign device to the branch circuit for this router, especially a device that switches on/off repeatedly (e.g., an airconditioner) with a relay or microswitch.
Page 309 Table 5-7 shows typical power consumption and heat dissipation figures. Each configuration assumes the maximum configuration. Table 5-7 Typical Power Consumption and Heat Dissipation Figures Configuration Input Power Condition Power Heat dissipat Consumption (A) Voltage Frequency GR2000-2S 100 Vac 50/60 ±1 Hz GR2000-4S 100 Vac 50/60 ±1 Hz...
Page 310 n (upper left side) In (upper right side) In (upper front end) Out (lower rear end) Out (lower right side) Out (lower left side) Out (center bottom)
Page 311 Out (left side) In (right side Figure 5-12 Airflow of GR2000-4 In (upper rear end) In (upper left side) In (upper right side)
Page 312 n (upper eft side) In (upper right side) In (upper front end)
Page 313 Heated air from the other device may be taken into this router, causing the intake air temperature to exceed the router’s environmental requirements. When the air intake or exhaust force of the other device is too strong, a rever pressure on this router’s intake air may arise, decreasing the cooling efficienc this router.
Page 315 Hardware Installatio Unpacking The GR2000 and any accessories will be delivered with a packing list. In each unpacking process, be sure to confirm the contents with the packing list. 6.1.1 Chassis GR2000-2S When unpacking this model, see Figure 6-1. Make sure that all the parts in the...
Page 316 Caution: This model weighs up to 25 kg. Handle with care. Work with another person when you handle this model. Vinyl bag or air Router chassis Carton...
Page 317 packing list are obtained from the cargo. Caution: This model weighs up to 55 kg. Handle with care. Work with another person when you handle this model. Router chassis...
Page 318 packing list are obtained from the cargo. Caution: This model weighs up to 120 kg. Handle with care. Work with another person when you handle this model. Carton Router chassis...
Page 319 packing list are obtained from the cargo. Caution: This model weighs up to 160 kg. Handle with care. Work with another person. Carton Router chassis...
Page 320 packing list are obtained from the cargo. Caution: This model weighs up to 25 kg. Handle with care. Vinyl bag Router chassis Carton...
Page 321 packing list are obtained from the cargo. Caution: This model weighs up to 85 kg. Handle with care. Work with another person. Carton Router chassis...
Page 322 packing list are obtained from the cargo. Caution: This model weighs up to 190 kg. Handle with care. Work with another person. Carton Router chassis...
Page 323: Rm/Rp/Nif Module
When unpacking a separately shipped RM/RP/NIF module, see Figure 6-9 and Figure 6-10. Make sure that all the parts in the packing list are obtained from th cargo. Caution: This component is subject to damage from static electricity. Before you are familiar with how to handle it in 6.2, do not unwrap the component.
Page 324: Memory Module
When unpacking a separately shipped memory module, see Figure 6-11. Make sure that all the parts in the packing list are obtained from the cargo. Caution: This component is subject to damage from static electricity. Before you are familiar with how to handle it in 6.2, do not unwrap the component. Memory module polyethylene or vinyl bag...
Page 325: Cable
When unpacking a separately shipped cable, see Figure 6-13. Make sure that all parts in the packing list are obtained from the cargo. Cable polyethylene or vinyl bag Carton Figure 6-13 Unpacking of Separately Shipped Cable Handling of Components Subject to Static Electricity...
Page 326 This section describes how to install the chassis of GR2000-2S, GR2000-10H, GR2000-20H, GR2000-4, GR2000-10, and GR2000-20. Before installing a target model, make sure the allowable style of installation according to Table 6-1, where “X” means applicable and “NA” means not applicable. Also determine the desktop/floor/ rack-mount installation layout, including minimum service clearance and area for airway, in accordance with 3.1 and Subsection 5.2.7.
Page 327 In this style of installation, place the router chassis to meet the minimum service clearance requirements, the cooling requirements, and the general rules as previously mentioned. Figure 6-15 shows GR2000-2S and GR2000-4 each instal on the desktop. GR2000-2S GR2000-4...
Page 328: Installation Of Chassis
Figure 6-17 Desktop Installation for GR2000-6H 6.3.3 Floor Installation of Chassis In this style of installation, place the router chassis to meet the minimum service clearance requirements, the cooling requirements, and the general rules as previously mentioned at first. Figure 6-18 through Figure 6-21 illustrate...
Page 331 procured earthquake-proof bolts (as necessary). Just locking the casters is allow as a temporary fixation during transportation, but this method is not allowed for installation. See Figure 6-22 through Figure 6-24 for the locations and dimensions of the screwjacks, earthquake-proof bolt holes, and casters for GR2000-10H, GR2000-2 GR2000-10, and GR2000-20 (unit: mm).
Page 332 Note 1 Note 3 Note 2 Screw jack Caster Note 1: Finish size of a screw jack Note 2: Ensure this because of necessity as air exhaust. Note 3: Use the screw jack for fixing the device. (Do not fix it by using the caster lock.) * When fixing it by using anchor bolts, keep the screw jacks (four) removed.
Page 333 opening for air Caster M12 nut (pitch 1.7 38.1 38.1 Screwjack*** 430.1 Caster Max. 34 * Max. rise of screwjack. ** Required space for exhaust air. *** When using earthquake-proof bolts, replace with them all screwja...
Page 334 Frame-base opening for air Caster Earthquake-proof bolt Screwjack Max. 50 Caster * Max. rise of screwjack.
Page 335 called UNDER SUPPORT instead of screwjacks. The steps are shown below. 1. Remove the M12 bolts attached or mounted to UNDER SUPPORT, and fasten them temporarily to the M12 bolt holes for the screwjacks. 2. Insert UNDER SUPPORT between the bottom of the router and the M12 bolts 3.
Page 336 1. Using a wrench, loosen the stopper nut (M12) of each screwjack on the target router; this allows you to adjust the screwjack. 2. Turn the screwjack counterclockwise until it lifts 10 mm from the floor surface. 3. Fasten again the stopper nut attached to each screwjack. 4.
Page 337 Each GR2000 model can be mounted in a 19-inch rack conforming to JIS and EI standards. When you choose this style of installation, ensure that the rack and t router meet the minimum service clearance requirements, the cooling requiremen and the general rules as previously mentioned. Then, follow one of the procedure below depending on the scale of the subject model: small, medium, or large.
Page 338 Power calbe Interface cable Metal bracket 19-inch rack (accessory of rack)
Page 339 19-inch rack Metal bracket (accessory of rack) Guide rail screw x 4 Approx. mass: 25kg (full options installed) Approx. dimensions (H x W x D): 133mm x 440mm x 480mm Metal bracket(accessory of rack) Rack fitting, t2 (Supplied)
Page 340 Metal bracket * * * * * * (accessory of rack) screw Approx. mass: 60kg (full options installed) Guide rail Approx. dimensions (H x W x D): 360mm x 430mm x 480mm...
Page 341 Approx. dimensions (H x W x D): 130mm x 440mm x 600mm Chassis (Front) (Rear) Interface cable Power cable Metal bracket 19-inch rack (accessory of rack)
Page 342 GR2000-10 (unit: mm). The steps are as follows: 1. Prepare the 19-inch rack, considering the dimensions of the router chassis. The inner depth of the rack must accommodate the depth of the router chassis plus minimum cable clearance (30mm for interface cables and 70mm for power cables) and minimum airway clearance (30mm).
Page 343 Interface (Rear) (Front) Guide rail cable Chassis Power cable 19-inch rack Metal bracket (accessory of...
Page 344 Approx. dimensions (H x W x D): 750mm (including caster) x 430mm x 600mm (Rear) (Front) (Rear) (Front) Interface Chassis (AC Input) Chassis (DC Input) cable Power cable Interface cable Guide rail...
Page 345 19-inch Rack GR2000-10H or GR2000-10 Guide Rail...
Page 346 Each POW is long and heavy (approx. 520mm deep, 8 kg). Removing Hold the handle and support the Fan Tray Removing bottom.
Page 347 GR2000-20 (unit: mm). The steps are as follows: 1. Prepare the 19-inch rack, considering the dimensions of the router chassis. The inner depth of the rack must accommodate the depth of the router chassis plus minimum cable clearance (30mm for interface cables and 70m for power cables) and minimum airway clearance (30mm).
Page 348 Approx. dimensions (H x W x D): 890mm (excluding caster) x 440mm x 600mm Guide rail Interface (Rear) (Front) cable Chassis Power cable 19-inch rack...
Page 349 Approx. dimensions (H x W x D): 1430mm (including caster) x 440mm x 600mm (Rear) (Front) (Rear) (Front) Interface Chassis (AC Input) Chassis (DC Input) cable Power cable Interfa cable Guide rail...
Page 351 547.95 133.35 177.8 177.8 1430...
Page 352 Open rack Device fitting screw hole Dedicated guide rail edicated bracket supplied with the evice fitting screws)
Page 353 19-inch Rack GR2000-20H or GR2000-20 Guide Rail...
Page 354: Routing And Connection Of Cables
This section describes how to route and connect the two types of cables to be connected to GR2000, i.e., input power cables and interface cables. 6.4.1 General Rules for Routing and Connection of Cables Regardless of the kind of cables, the following must be observed when you route and connect the cables: Protect cables by running them through a duct or by using a braid.
Page 355 Cabinet Cabinet o not route cables like this. Cables are Route cables in this manner so that th bstructing board replacement. do not obstruct board replacement. Secure additional length to facilitate replacement work. Figure 6-40 Prohibited vs. Preferred Cable Routing on Floor-Installed GR2000...
Page 356 Metal fittings (supplied as accessories) M4 screws (supplied as accessories) NIF side...
Page 357 Metal fittings ( 4 screws supplied as (supplied as accessories) accessories) NIF side Figure 6-44 Fixation of Cables on Large-Scale Models Using Metal Fittings (GR2000-10H)
Page 358: Gr2000-2S
This subsection shows you how to connect input power cables to specific models of GR2000-2S, GR2000-10H, GR2000-20H, GR2000-4, GR2000-10, and GR2000-20. 6.4.2.1 GR2000-2S Figure 6-46 shows how to connect the input power cable to GR2000-2S, which accepts only AC input (100V or 200V). The steps are as follows: 1.
Page 359 Connect both power cables if there is a redundant power supply. Power Switch...
Page 360 Tighten the screws. -48V Ground (note) Power supply cable. Secure it in place with the cable clamp. Note: Due to the difference in level, the ground connection is connected to the terminal from above...
Page 361 Figure 6-47 shows how to connect the AC input power cable to GR2000-10H. Th steps are as follows: 1. Ensure that the power switch (for 200V input) or the breaker switch (for 100V input) in the front end of the chassis is in the O (out) position. When the pow supply is duplexed (redundant), make sure in two positions.
Page 362 this connection work requires expertise, the work must be conducted by qualified personnel. The steps are as follows: 1. Procure the DC input power cable in compliance with the specifications shown below. When the power supply is duplexed (redundant), procure two cables. Cord structure: 3-wire AWG No.
Page 363 ø5.3 Min. 8.3 Min. Unit: mm Figure 6-49 Terminal Board/Wire Dimensions for DC Input to GR2000-10H 6.4.2.5 GR2000-20H 200V AC Input Figure 6-50 shows how to connect the AC input power cable to GR2000-20H. Th steps are as follows: 1. Prepare the AC input power cable supplied with the device. The cable complie...
Page 364 Front Breaker switch Terminal board...
Page 365 this connection work requires expertise, the work must be conducted by qualified personnel. The steps are as follows: 1. Procure the DC input power cable in compliance with the specifications show below. When the power supply is duplexed (redundant), procure two cables. Cord structure: 3-wire AWG No.
Page 366 ø6.4 Min. 9.3 Min. Unit: mm Figure 6-53 Terminal Board/Wire Dimensions for DC Input to GR2000-20H 6.4.2.6 GR2000-4 Figure 6-54 shows how to connect the input power cable to GR2000-4, which accepts only AC input (100V or 200V). The steps are as follows: 1.
Page 367 Figure 6-55 shows how to connect the AC input power cable to GR2000-10. The steps are as follows: 1. Ensure that the power switch in the front end of the chassis is in the O (out) position. When the power supply is duplexed (redundant), make sure in two positions.
Page 368 this connection work requires expertise, the work must be conducted by qualified personnel. The steps are as follows: 1. Procure the DC input power cable in compliance with the specifications shown below. When the power supply is duplexed (redundant), procure two cables. Cord structure: 3-wire AWG No.
Page 369 Front Breaker switch Rear...
Page 370 Figure 6-58 shows how to connect the AC input power cable to GR2000-20. The steps are as follows: 1. Ensure that the power switch in the front end of the chassis is in the O (out) position. When the power supply is duplexed (redundant), make sure in two positions.
Page 371 this connection work requires expertise, the work must be conducted by qualified personnel. The steps are as follows: 1. Procure the DC input power cable in compliance with the specifications show below. When the power supply is duplexed (redundant), procure two cables. Cord structure: 3-wire AWG No.
Page 372: Connection Of Interface Cables
ø5.3 Min. 8.3 Min. Unit: mm Figure 6-60 Terminal Board/Wire Dimensions for DC Input to GR2000-20 6.4.3 Connection of Interface Cables This subsection depicts how to connect interface cables to the own router, assuming that such cables are already routed. Make sure that the general rules for cabling in Subsection 6.4.1 are satisfied.
Page 373 or 1000BASE-LH cable connector (SC 2-core) to the mating receptacle on the own router. When connecting, push until a click. When removing, just pull. SC 2-core Figure 6-62 Connection of 100BASE-FX, 1000BASE-SX, 1000BASE-LX, or 1000BASE Cable Connector (SC 2-core) 6.4.3.3 WAN: V.24, V.35, and X.21...
Page 374 RJ-48) to the mating receptacle on the own router. Caution: 10BASE-T, 100BASE-TX, WAN (BRI/PRI), and 25Mbps ATM all use the same 8-pin modular connector. Ensure the same interface type between the connector and the receptacle prior to physical connection. A mismatch may cause malfunction or a failure.
Page 375: Atm/Mmf/Smf: Oc-3C Atm/Mmf, Oc-3C Atm/Smf, Oc-12C/Atm/Mmf And Oc-12C Atm/Smf
connector (SC 2-core) to the mating receptacle on the own router. When connecting, push until a click. When removing, just pull. SC 2-core Figure 6-66 Connection of OC-3c POS, OC-12c POS, or OC-48c POS Cable Connect (SC 2-core) 6.4.3.7 ATM/MMF/SMF: OC-3c ATM/MMF, OC-3c ATM/SMF, OC-12c/ATM/MMF and OC-12c ATM/SMF...
Page 376 mating receptacle on the own router. Caution: 10BASE-T, 100BASE-TX, WAN (BRI/PRI), and 25Mbps ATM all use the same 8-pin modular connector. Ensure the same interface type between the connector and the receptacle prior to physical connection. A mismatch may cause malfunction or a failure. 8-pin modular (RJ-45)
Page 377 Figure 6-70 illustrates how to unmount an MC. Note: When the setup console is connected, access to Lever #1 may be difficult because this lever is adjacent to the console port. In such a case, temporarily disconnect the console cable and operate the lever. Lever #0 Card slot #0 Card slot #1...
Page 378 Methods of fitting/removing the GBIC to NEIG-4C are described below: How to fit. (1) Push the modules in securely to the end. (2) Let the lever fall down. Note: Push it in until "click" is heard. (1) Raise the lever, and push it in securely to the In case of Module B In case of Module A...
Page 379 After the hardware installation is complete, initial setup of this router from the se console is mandatory. To prepare for this operation, connect the setup console to router’s RS-232C port with a cross cable having 9-pin D-sub female connectors o both ends.
Page 380: Console Specifications
Table 6-2 Console specifications Item Specifications Communication parameter 8 bits and 1 stop bit, without parity. Communication speed 19.2 kbps 9600 bps 4800 bps 2100 bps 1200 bps The communication speed varies depending on the port connected to the console. When connecting the console to CONSOLE (RS232C), the communication speed can be selected from the above table.
Page 381: Overview Of Device Operation
Starting, Setting Up, and Stoppin Overview of Device Operation Figure 7-1 provides a sequence of operating this device. Start Initial installation?
Page 382 Starting the own router is performed by turning on the power switch or the power breaker on each router chassis. See Subsection 6.4.2 for the locations and in/out positions of these power switches and breaker switches. Pay attention to the following Notes.
Page 383 When the hardware installation is complete, you must configure the system to st operation. The steps are as follows: 1. Login at first time. Log in to this device from the setup console. At the initial lo attempt, the following appears as the default login account: Login name: o p e r a t o r Password: (none)
Page 385: Chapter 8 - Adding And Removing Components
Adding and Removing Component The user’s own addition and removal of components is available on this router, basically while the router power is off. In addition, under certain conditions, components can be added and removed while the router power is on. This hot-swapping capability and its procedures for applicable components are descri in the last section in this chapter.
Page 388 Guide rail Anchor screw...
Page 389: Power Supply Components
To add or remove the power supply components to/from each model of GR2000 ot than GR2000-2S, refer to the following subsections. Note: The power supply module of GR2000-2S cannot be added or removed by the user because they are integral to chassis. When addition or removal of such a module is necessitated on GR2000-2S, entrust work to trained service personnel.
Page 390 Caution: The power source unit is heavy (about 8kg); be sure to support it firmly from below with both hands when installing or removing.
Page 391 Caution: The power source unit is heavy (about 8kg); be sure to support it firmly from below with both hands when installing or removing.
Page 392: Input Unit (Ac Or Dc)
8.2.3.1 Input Unit (AC or DC) 1. Turn off the power switch (AC input) or the breaker switch (DC input) on the Input Unit and unplug the power cord from the Input Unit. 2. Follow the instructions illustrated in Figure 8-4. Although the figure shows the case of AC input, the same instructions apply to the case of DC input.
Page 393: Dc-Dc Unit
2. Follow the instructions illustrated in Figure 8-5. DC-DC unit power switch...
Page 394: Input Unit (Ac Or Dc)
8.2.4.1 Input Unit (AC or DC) 1. Turn off the breaker switch on the Input Unit and unplug the power cord from the Input Unit. 2. If the Input Unit is for AC input, detach the cover in front of the target Input Unit as illustrated in Figure 8-6.
Page 395: Dc-Dc Unit
2. Follow the instruction illustrated in Figure 8-7. DC-DC unit power switch...
Page 396: Gr2000-4
Figure 8-8 illustrates how to remove a POW from GR2000-4. The steps are as follows: 1. Turn off the power switch on the POW and unplug the power cord from the POW. 2. Demount the screws. 3. Remove the POW. Power Switch...
Page 397: Pow For Ac Input
8.2.6.1 POW for AC Input 1. Turn off the power switch on the POW and unplug the power cord from the P 2. Follow the instructions illustrated in Figure 8-9. Using the Latches...
Page 398 POW. 2. Follow the instructions illustrated in Figure 8-10. Using the latches...
Page 399: Pow For Ac Input
8.2.7.1 POW for AC Input 1. Turn off the power switch on the POW and unplug the power cord from the P 2. Follow the instructions illustrated in Figure 8-11. A dju st th e p ro je ctio n s...
Page 400 POW. 2. Follow the instructions illustrated in Figure 8-12. Power off the four pairs of circuit breakers, and remove the power connection code. Procedures of install/remove are shown below.
Page 401: Gr2000-10H
To add or remove the fans to/from each model of GR2000 other than GR2000-2S refer to the following subsections. Note: The fans of GR2000-2S cannot be added or removed by the user because they are integral to chassis. When addition or removal of such a fan is necessitated on GR2000-2S, entrust work to trained service personnel.
Page 402: Gr2000-20H
To add or remove the fan tray for GR2000-20H, follow the instructions illustrated in Figure 8-14. Fan tray Cover...
Page 403: Cpu Fan For Gr2000-4, Gr2000-10, And Gr2000-20
To add or remove the CPU fan for GR2000-4, GR2000-10, and GR2000-20, follow instructions illustrated in Figure 8-15. When adding, be sure to attach the safety clamp to the socket hook to anchor the CPU fan. Safety clamp Fix the CPU fan by hooking safety clamp to the socket hook.
Page 404: Main Memory
To add or remove the fans to/from each model of GR2000 other than GR2000-2S, refer to the following subsections. Note: The main memory modules of GR2000-2S cannot be added or removed by the user because RM-CPU and RMP of GR2000-2S are integral to chassis. When addition or removal of main memory module is necessitated on GR2000-2S, entrust work to trained service personnel.
Page 405 To add or remove the main memory module for RP, follow the instructions illustra in Figure 8-17. Installed connector...
Page 406: Removing A Bcu
on or off. After completing this procedure, start up duplex mode from your terminal by entering: [ c o n f i g : ] m o d e s e t d u p l e x [ C R ] Note: When adding a standby BCU with power off, the above command is unnecessary because duplex mode is automatically detected and power turned on, unless you change duplex mode to simplex mode or press the EMA SUPRESS button.
Page 407: Adding An Rp
8.5.2.1 Adding an RP To add an RP: 1. Mount the RP board in an empty RP slot. 2. To start the RP, enter the following command from your terminal: [ c o n f i g : ] m a i n t e n a n c e f r e e r p < r p _ n o > [ C R ] 8.5.2.2 Removing an RP To remove an RP:...
Page 408 1. Stop the operation of the GBIC to be removed. Charge the following commands from the control terminal: [Input type] maintenance close nif <nif_no> line <line_no> (nif_no = NIF number being the object; line_no = LINE number being the object.) *1 2.
Page 409: Chapter 9 - Software Installation And Updates
Software Installation and Update Introduction The control software for the GR2000 is shipped pre-installed. While it is usually unnecessary to reinstall the software, there is a complete procedure for doing so, well as a procedure to update the software to another release. Use update and ins procedures below when replacing the software or installing it in a new MC: Install Use this procedure to install software on a new MC.

Hitachi GR2000 Series Installation Manual

Table of Contents

Table of Contents

List of Figures

Chapter 4 - Precautions in Planning Installation

Chapter 5 - Installation Site Conditions

Chapter 6 - Hardware Installation

Chapter 7 - Starting, Setting Up, and Stopping

List of Tables

Chapter 1 - General Information

Chapter 2 - Product Overview

Chapter 3 - Component Details

3.4 Routing Processor (Rp)

Chapter 8 - Adding and Removing Components

Chapter 9 - Software Installation and Updates

Quick Links

Chapters

Related Manuals for Hitachi GR2000 Series

Summary of Contents for Hitachi GR2000 Series