Sony ODS-D280U Service Manual page 96

Code Description
20-D17 Displacement of cartridge
was detected during vertical
movement to upper direction
of the select mechanism.
20-D18 Abnormal current was detec-
ted in the up/down motor
during vertical movement to
upper direction of the select
mechanism.
20-D1E Displacement of standard
position was detected during
vertical movement to upper
direction of the select mech-
anism.
*1: For the ODS-D280F, perform "Eject" operation from the PC (or host device) or press the EJECT button on the rear of the drive to eject the
cartridge.
Note
EJECT button operation or power off/on operation may generate another alarm code.
ODS-D280U/ODS-D280F
Error remedy method
1. Press the EJECT button to eject the cartridge.
1. Eject a cartridge manually.
If the cartridge is not ejected, take the following
2. Visually check the cartridge.
measures.
• If an abnormality (such as bulge) is
• Turn off and on the drive. Press the EJECT
found, do not use the cartridge any lon-
button after startup to eject the cartridge.
ger.
• If the cartridge is not ejected even after this
Tip
operation, eject it manually.
For how to handle the defective car-
tridge, contact your local Sony Sales
Office/Service Center.
2. Visually check the cartridge.
3. Startup the maintenance menu and perform
• If an abnormality (such as bulge) is found, do not use the cartridge any longer and go to step 4) in Measures.
LOADER AUTO TEST.
Tip
For how to handle the defective cartridge, contact your local Sony Sales Office/Service Center. Note
3. Insert the same cartridge and check whether this error occurs again.
To clear this error, perform LOADER AUTO
If the cartridge cannot be inserted, turn off and on the drive and then insert the cartridge again.
TEST
• When this error occurs again, go to step 4) in Measures.
Use another cartridge.
• When this error no longer occurs, use the unit as it is.
4. Insert another cartridge and check whether this error occurs again. • When this test ends successfully, the
• When this error no longer occurs, check the following.
previous cartridge may be defective.
- When this error occurs again by checking shown in step 3) in Measures, the previous cartridge may be
Do not use the previous cartridge any
defective. Do not use the previous cartridge any longer.
longer.
Tip
Tip
For how to handle the defective cartridge, contact your local Sony Sales Office/Service Center.
For how to handle the defective car-
- When this error no longer occurs by checking shown in step 3) in Measures, use the unit as it is.
tridge, contact your local Sony Sales
• When this error occurs again, the select loader assembly may be defective.
Office/Service Center.
• When this test ends abnormally, the
select loader assembly may be defec-
tive.
1. Eject a cartridge manually.
2. Visually check the cartridge.
• If an abnormality (such as bulge) is
found, do not use the cartridge any lon-
ger.
Tip
For how to handle the defective car-
tridge, contact your local Sony Sales
Office/Service Center.
3. Startup the maintenance menu and perform
LOADER AUTO TEST.
Note
To clear this error, perform LOADER AUTO
TEST
Use another cartridge.
• When this test ends successfully, the
previous cartridge may be defective.
Do not use the previous cartridge any
longer.
Tip
For how to handle the defective car-
tridge, contact your local Sony Sales
Office/Service Center.
• When this test ends abnormally, the
select loader assembly may be defec-
tive.
Insert a cartridge and check whether this error oc-
curs again.
If the cartridge cannot be inserted, turn off and on
the drive and then insert the cartridge again.
• When this error occurs again, the select load-
er assembly may be defective.
• When this error no longer occurs, use the unit
as it is.
Refer to section
"1-10. How to Eject the Car-
*1
tridge (ODS-D280F)"
"1-11. How to Eject the Car-
tridge Manually"
"4-10. Select Loader Assembly"
"1-11. How to Eject the Car-
tridge Manually"
"4-10. Select Loader Assembly"
"6-4-4. LOADER AUTO
TEST"
"4-10. Select Loader Assembly"
Continued
2-48