Table of Contents
Advertisement
Code
Description
95-520
The offset adjustment value
of the acceleration sensor
(IC202 or IC203: BI-353
(ODS-D280U)/BF-92
(ODS-D280F) board) cannot
be read from the SPI EE-
PROM (IC206: BI-353
(ODS-D280U)/BF-92
(ODS-D280F) board).
95-522
After a firmware error of the
BRIDGE (IC700 internal:
BI-353 (ODS-D280U)/
BF-92 (ODS-D280F) board)
was detected, it was restar-
ted.
95-523
After a firmware error of the
BRIDGE (IC700 internal:
BI-353 (ODS-D280U)/
BF-92 (ODS-D280F) board)
or a hardware error was de-
tected, the BRIDGE was re-
started.
95-524
An error was detected during
the BRIDGE (IC700 inter-
nal: BI-353 (ODS-D280U)/
BF-92 (ODS-D280F) board)
firmware interrupt process-
ing.
95-525
After a BRIDGE (IC700 in-
ternal: BI-353 (ODS-
D280U)/BF-92 (ODS-
D280F) board) firmware er-
ror was detected, it was re-
started.
95-526
No data can be read from
FeRAM (IC201: BI-353
board (ODS-D280U)/BF-92
board (ODS-D280F)).
95-527
An FeRAM (IC201: BI-353
board (ODS-D280U)/BF-92
board (ODS-D280F)) error
was detected.
95-528
An FeRAM (IC201: BI-353
board (ODS-D280U)/BF-92
board (ODS-D280F)) load-
ing information data error
was detected.
95-529
Failed to write loading infor-
mation data to FeRAM
(IC201: BI-353 board (ODS-
D280U)/BF-92 board (ODS-
D280F))
95-52A
False setting of this unit se-
rial number was detected.
ODS-D280U/ODS-D280F
Error remedy method
1.
Acquire the drive/driver log.
If the same error occurs repeatedly, send the
acquired drive/driver log to your local Sony
Sales Office/Service Center.
2.
Turn off and on the power.
1.
Acquire the drive/driver log.
If the same error occurs repeatedly, send the
acquired drive/driver log to your local Sony
Sales Office/Service Center.
2.
Turn off the power.
1.
Acquire the drive/driver log.
If the same error occurs repeatedly, send the
acquired drive/driver log to your local Sony
Sales Office/Service Center.
2.
Turn off the power.
1.
Acquire the drive/driver log.
If the same error occurs repeatedly, send the
acquired drive/driver log to your local Sony
Sales Office/Service Center.
2.
Turn off the power.
1.
Acquire the drive/driver log.
If the same error occurs repeatedly, send the
acquired drive/driver log to your local Sony
Sales Office/Service Center.
2.
Turn off the power.
1.
Acquire the drive/driver log.
If the same error occurs repeatedly, send the
acquired drive/driver log to your local Sony
Sales Office/Service Center.
2.
Turn off and on the power.
1.
Acquire the drive/driver log.
If the same error occurs repeatedly, send the
acquired drive/driver log to your local Sony
Sales Office/Service Center.
2.
Turn off and on the power.
1.
Eject a cartridge.
2.
Turn off and on the power.
1.
Eject a cartridge.
2.
Turn off and on the power.
3.
Insert the cartridge again.
If this error occurs again, the BI-353 board
(ODS-D280U) or BF-92 board (ODS-
D280F) may be defective.
•
After the BI-353 board (ODS-D280U)/
BF-92 board (ODS-D280F) or the DR-683
board is replaced, take necessary actions.
•
When this error occurs after performing op-
tical drive adjustment, perform optical drive
adjustment again.
Note
This error can also occur if the optical drive
adjustment fails.
Refer to section
―
―
―
―
―
―
―
―
―
"1-16. Service Action after Re-
placing Blocks and Mounted
Boards"
"4-19. BI-353/BF-92 Board"
"5. Adjustment of Optical Drive
System"
Continued
2-76
Advertisement
Table of Contents
