Sony ODS-D280U Service Manual page 95

Code Description
20-C18 Abnormal current was detec-
ted in the up/down motor
during vertical movement to
lower direction of the select
mechanism.
20-C1E Displacement of standard
position was detected during
vertical movement to lower
direction of the select mech-
anism.
20-D11 Vertical movement to upper
direction of the select mech-
anism did not end within the
specified time period.
*1: For the ODS-D280F, perform "Eject" operation from the PC (or host device) or press the EJECT
button on the rear of the drive to eject the cartridge.
Note
EJECT button operation or power off/on operation may generate another alarm code.
ODS-D280U/ODS-D280F
Error remedy method
1. Eject a cartridge manually.
2. Visually check the cartridge.
• If an abnormality (such as bulge) is
found, do not use the cartridge any lon-
ger.
Tip
For how to handle the defective car-
tridge, contact your local Sony Sales
Office/Service Center.
3. Startup the maintenance menu and perform
LOADER AUTO TEST.
Note
To clear this error, perform LOADER AUTO
TEST
Use another cartridge.
• When this test ends successfully, the
previous cartridge may be defective.
Do not use the previous cartridge any
longer.
Tip
For how to handle the defective car-
tridge, contact your local Sony Sales
Office/Service Center.
• When this test ends abnormally, the
select loader assembly may be defec-
tive.
Insert a cartridge and check whether this error oc-
curs again.
If the cartridge cannot be inserted, turn off and on
the drive and then insert the cartridge again.
• When this error occurs again, the select load-
er assembly may be defective.
• When this error no longer occurs, use the unit
as it is.
1. Eject a cartridge manually.
2. Visually check the cartridge.
• If an abnormality (such as bulge) is
found, do not use the cartridge any lon-
ger.
Tip
For how to handle the defective car-
tridge, contact your local Sony Sales
Office/Service Center.
3. Startup the maintenance menu and perform
LOADER AUTO TEST.
Note
To clear this error, perform LOADER AUTO
TEST
Use another cartridge.
• When this test ends successfully, the
previous cartridge may be defective.
Do not use the previous cartridge any
longer.
Tip
For how to handle the defective car-
tridge, contact your local Sony Sales
Office/Service Center.
• When this test ends abnormally, the
select loader assembly may be defec-
tive.
Refer to section
"1-11. How to Eject the Car-
tridge Manually"
"4-10. Select Loader Assembly"
"6-4-4. LOADER AUTO
TEST"
"4-10. Select Loader Assembly"
"1-10. How to Eject the Car-
tridge (ODS-D280F)"
"1-11. How to Eject the Car-
tridge Manually"
"4-10. Select Loader Assembly"
1. Press the EJECT button to eject the cartridge.
If the cartridge is not ejected, take the following measures.
• Turn off and on the drive. Press the EJECT button after
startup to eject the cartridge.
• If the cartridge is not ejected even after this operation, eject
it manually.
2. Visually check the cartridge.
• If an abnormality (such as bulge) is found, do not use the
cartridge any longer and go to step 4) in Measures.
Tip
For how to handle the defective cartridge, contact your local
Sony Sales Office/Service Center.
3. Insert the same cartridge and check whether this error occurs
again.
If the cartridge cannot be inserted, turn off and on the drive and
then insert the cartridge again.
• When this error occurs again, go to step 4) in Measures.
• When this error no longer occurs, use the unit as it is.
4. Insert another cartridge and check whether this error occurs
again.
• When this error no longer occurs, check the following.
- When this error occurs again by checking shown in step 3)
in Measures, the previous cartridge may be defective. Do not
use the previous cartridge any longer.
Tip
Continued
For how to handle the defective cartridge, contact your
local Sony Sales Office/Service Center.
- When this error no longer occurs by checking shown in
step 3) in Measures, use the unit as it is.
• When this error occurs again, the select loader assembly may
be defective.
*1
2-47