Main
Sub
Error
Code
Code
Logger
C61
○
96
907
○
90A
○
930
○
942
○
960
○
961
○
A07
○
A0A
○
A30
○
A42
○
A60
○
A61
○
B07
○
B0A
○
B30
○
B42
○
B60
○
B61
○
C07
○
C0A
○
C30
○
C42
○
C60
○
C61
○
ODS-D280U/ODS-D280F
Alarm
Alarm
Description
Status
Indica-
tor
Blinking
Cycle
○
0.25 sec.
A servo firmware communication error was detected in Disc
Drive LSI 1b (Base Drive) (On side 0).
○
0.25 sec.
Head data cannot be read from the EEPROM in optical block
assembly Ch-2A. (On side 1)
○
1 sec.
A mismatch of OP ID was detected in the hour meter data on the
Ch-2A side and the EEPROM data of the optical block assembly
Ch-2A. (On side 1)
○
0.25 sec.
There is no response from the optical block assembly Ch-2A.
(On side 1)
○
1 sec.
Disc Drive LSI 2a (Base Drive) cannot write data to the FLASH
(Base Drive). (On side 1)
○
0.25 sec.
A system error was detected in Disc Drive LSI 2a (Base Drive).
(On side 1)
○
0.25 sec.
A servo firmware communication error was detected in Disc
Drive LSI 2a (Base Drive) (On side 1).
○
0.25 sec.
Head data cannot be read from the EEPROM in optical block
assembly Ch-2B. (On side 1)
○
1 sec.
A mismatch of OP ID was detected in the hour meter data on the
Ch-2B side and the EEPROM data of the optical block assembly
Ch-2B. (On side 1)
○
0.25 sec.
There is no response from the optical block assembly Ch-2B.
(On side 1)
○
1 sec.
Disc Drive LSI 2b (Base Drive) cannot write data to the FLASH
(Base Drive). (On side 1)
○
0.25 sec.
A system error was detected in Disc Drive LSI 2b (Base Drive).
(On side 1)
○
0.25 sec.
A servo firmware communication error was detected in Disc
Drive LSI 2b (Base Drive) (On side 1).
○
0.25 sec.
Head data cannot be read from the EEPROM in optical block
assembly Ch-3A. (On side 1)
○
1 sec.
A mismatch of OP ID was detected in the hour meter data on the
Ch-3A side and the EEPROM data of the optical block assembly
Ch-3A. (On side 1)
○
0.25 sec.
There is no response from the optical block assembly Ch-3A.
(On side 1)
○
1 sec.
Disc Drive LSI 3a (Base Drive) cannot write data to the FLASH
(Base Drive). (On side 1)
○
0.25 sec.
A system error was detected in Disc Drive LSI 3a (Base Drive).
(On side 1)
○
0.25 sec.
A servo firmware communication error was detected in Disc
Drive LSI 3a (Base Drive) (On side 1).
○
0.25 sec.
Head data cannot be read from the EEPROM in optical block
assembly Ch-3B. (On side 1)
○
1 sec.
A mismatch of OP ID was detected in the hour meter data on the
Ch-3B side and the EEPROM data of the optical block assembly
Ch-3B. (On side 1)
○
0.25 sec.
There is no response from the optical block assembly Ch-3B.
(On side 1)
○
1 sec.
Disc Drive LSI 3b (Base Drive) cannot write data to the FLASH
(Base Drive). (On side 1)
○
0.25 sec.
A system error was detected in Disc Drive LSI 3b (Base Drive).
(On side 1)
○
0.25 sec.
A servo firmware communication error was detected in Disc
Drive LSI 3b (Base Drive) (On side 1).
2-14