Main
Sub
Error
Code
Code
Logger
70E
○
907
○
90A
○
930
○
942
○
960
○
961
○
A07
○
A0A
○
A30
○
A42
○
A60
○
A61
○
B07
○
B0A
○
B30
○
B42
○
B60
○
B61
○
C07
○
C0A
○
C30
○
C42
○
C60
○
ODS-D280U/ODS-D280F
Alarm
Alarm
Description
Status
Indica-
tor
Blinking
Cycle
○
1 sec.
The BF-92 board (Fibre channel block) detected a high temper-
ature. (ODS-D280F only)
○
0.25 sec.
Head data cannot be read from the EEPROM in optical block
assembly Ch-0A. (On side 0)
○
1 sec.
A mismatch of OP ID was detected in the hour meter data on the
Ch-0A side and the EEPROM data of the optical block assembly
Ch-0A. (On side 0)
○
0.25 sec.
There is no response from the optical block assembly Ch-0A.
(On side 0)
○
1 sec.
Disc Drive LSI 0a (Base Drive) cannot write data to the FLASH
(Base Drive). (On side 0)
○
0.25 sec.
A system error was detected in Disc Drive LSI 0a (Base Drive).
(On side 0)
○
0.25 sec.
A servo firmware communication error was detected in Disc
Drive LSI 0a (Base Drive) (On side 0).
○
0.25 sec.
Head data cannot be read from the EEPROM in optical block
assembly Ch-0B. (On side 0)
○
1 sec.
A mismatch of OP ID was detected in the hour meter data on the
Ch-0B side and the EEPROM data of the optical block assembly
Ch-0B. (On side 0)
○
0.25 sec.
There is no response from the optical block assembly Ch-0B.
(On side 0)
○
1 sec.
Disc Drive LSI 0b (Base Drive) cannot write data to the FLASH
(Base Drive). (On side 0)
○
0.25 sec.
A system error was detected in Disc Drive LSI 0b (Base Drive).
(On side 0)
○
0.25 sec.
A servo firmware communication error was detected in Disc
Drive LSI 0b (Base Drive) (On side 0).
○
0.25 sec.
Head data cannot be read from the EEPROM in optical block
assembly Ch-1A. (On side 0)
○
1 sec.
A mismatch of OP ID was detected in the hour meter data on the
Ch-1A side and the EEPROM data of the optical block assembly
Ch-1A. (On side 0)
○
0.25 sec.
There is no response from the optical block assembly Ch-1A.
(On side 0)
○
1 sec.
Disc Drive LSI 1a (Base Drive) cannot write data to the FLASH
(Base Drive). (On side 0)
○
0.25 sec.
A system error was detected in Disc Drive LSI 1a (Base Drive).
(On side 0)
○
0.25 sec.
A servo firmware communication error was detected in Disc
Drive LSI 1a (Base Drive) (On side 0).
○
0.25 sec.
Head data cannot be read from the EEPROM in optical block
assembly Ch-1B. (On side 0)
○
1 sec.
A mismatch of OP ID was detected in the hour meter data on the
Ch-1B side and the EEPROM data of the optical block assembly
Ch-1B. (On side 0)
○
0.25 sec.
There is no response from the optical block assembly Ch-1B.
(On side 0)
○
1 sec.
Disc Drive LSI 1b (Base Drive) cannot write data to the FLASH
(Base Drive). (On side 0)
○
0.25 sec.
A system error was detected in Disc Drive LSI 1b (Base Drive).
(On side 0)
Continued
2-13