Table of Contents
Advertisement
Lo-
Part to Be
Hours Meter
cat-
Replaced
(Menu Item)
ion
No.
(1)
Optical block
Laser parameter
assembly
(Laser Parameter)
OP0/1
(2)
Optical block
assembly
OP2/3
(3)
Roller gear as-
Number of disc trans-
sembly
portation times
(Disc Guide Counter)
(4)
CA arm L cov-
er assembly
(5)
CA anti-static
brush assembly
(6)
SE anti-static
brush assembly
(7)
Anti-static
brush assembly
2 (RP)
(8)
CA upper as-
Number of disc trans-
sembly (RP)
portation times
The counter with a
larger number of times,
Carry Motor (H) Coun-
ter or Carry Motor (V)
Counter
(9)
Air filter
Air filter parameter
(Air Filter Parameter)
*1: The replacement cycle of the optical block assembly of several lots from the initial shipping is 6,700. For more
details, contact your local Sony Sales Office/Service Center.
*2: When replacing the optical device assembly (RP) (parts number: A-2167-948-A), perform the procedure below.
1.
Upgrade the firmware. (Refer to
2.
Execute "UPLOAD TO DR (MAIN)" or "UPLOAD TO DR (SUB)" of the maintenance menu. (Refer to
UPLOAD TO DR (MAIN)"
3.
Adjust the optical drive. (Refer to
4.
Reset the Seek Counter 0/1/2/3 and the Spindle Running Hours. (Refer to
*3: When the air filter parameter reaches 8,000, the error code 3F-511 is displayed. If the error code 3F-511 is displayed,
replace the air filter immediately. If it is continuously used as it is, it may cause a trouble or write/read failure. For details
on the replacement procedure and the procedure after replacement of the air filter, refer to the installation manual supplied
with the air filter for replacement.
*4: Be sure to perform
"3-2-3. Cleaning the Carry Loader Assembly"
same time as the replacement of parts.
*5: After replacing the CA upper assembly (RP), reset both Carry Motor (H) Counter and Carry Motor (V) Counter.
ODS-D280U/ODS-D280F
Replace-
ment Cycle
Every 13,400
*1
Every 60,000
times *4
Every 60,000
times
Every 8,000
*3
"7. Firmware
Upgrade")
or
"6-7-4. UPLOAD TO DR
"5. Adjustment of Optical Drive
Part No. and
Reference
Part Name
A-2186-362-A
"4-30. Main
Main base assembly
Base Assem-
(RP) *2
bly"
A-2186-363-A
"4-29. Sub
Sub base assembly
Base Assem-
(RP) *2
bly"
A-1955-050-A
"4-24. Roller
Roller gear assembly
Gear Assem-
bly"
A-2167-401-A
"4-25. CA Arm
CA arm L cover as-
L Cover As-
sembly
sembly"
A-2167-950-A
"4-23. CA An-
CA anti-static brush
ti-Static Brush
assembly (RP)
Assembly/CA
Anti-Static
Brush Assem-
bly 2"
A-2167-951-A
"4-28. SE Anti-
SE anti-static brush
Static Brush
assembly (RP)
Assembly"
A-5011-777-A
"4-23. CA An-
Anti-static brush as-
ti-Static Brush
sembly 2 (RP)
Assembly/CA
Anti-Static
Brush Assem-
bly 2"
A-5015-517-A
"4-14. CA Up-
CA upper assembly
per Assembly"
(RP)
A-2181-544-A
"4-26. Air Fil-
Air filter (RP)
ter"
(SUB)")
System")
"6-7-8. RESET
and
"3-2-4. Cleaning the Spindle Motor"
Hours meter
data resets
necessary or
unnecessary
Unnecessary
Unnecessary
Necessary
Necessary
Necessary
Necessary
Necessary
Necessary *5
Necessary *3
"6-7-3.
HOURS")
at the
3-3
Advertisement
Table of Contents
