Dodge Sprinter 2006 Manual page 2013

VA
INSTALLA TION
Passenger Van
(1) P osit ion t r im pa n els a n d sea t pu sh -pin fa st en -
er s fu lly.
(2) In st a ll d-pilla r t r im , if n ecessa r y. (Refer t o 23 -
BODY/INTE RIOR/D-P ILLAR TRIM - INSTALLA-
TION)
(3) In st a ll sea t s, if n ecessa r y. (Refer t o 23 - BODY/
SE ATS/SE AT - INSTALLATION)
Cargo Van
(1) In st a ll pa n elin g a n d r epla ce r ivet s.
(2) In st a ll t ie down r in gs a n d bolt s, if equ ipped.
REAR V I EW M I RROR
REMOVAL
(1) Slide m ir r or off su ppor t br a cket .
I N STALLAT I ON
INSTALLA TION
(1) In st a ll t h e su ppor t br a cket if n ecessa r y. (Refer
t o 23 - BODY/INTE RIOR/RE AR VIE W MIRROR -
INSTALLATION - SUP P ORT BRACKE T)
(2) Slide m ir r or on t o su ppor t br a cket fu lly.
INSTALLA TION - REAR VIEW MIRROR SUP-
PORT BRACKET
(1) Ma r k t h e posit ion for t h e m ir r or br a cket on t h e
ou t side of t h e win dsh ield gla ss wit h a wa x pen cil.
(2) Clea n t h e br a cket con t a ct a r ea on t h e gla ss.
Use a m ild powder ed clea n ser on a clot h sa t u r a t ed
wit h isopr opyl (r u bbin g) a lcoh ol. F in a lly, clea n t h e
gla ss wit h a pa per t owel da m pen ed wit h a lcoh ol.
(3) Sa n d t h e su r fa ce on t h e su ppor t br a cket wit h
fin e gr it -sa n dpa per. Wipe t h e br a cket su r fa ce clea n
wit h a pa per t owel.
(4) Apply a cceler a t or t o t h e su r fa ce on t h e br a cket
a ccor din g t o t h e followin g in st r u ct ion s:
(a ) Cr u sh t h e via l t o sa t u r a t e t h e felt a pplica t or.
(b) Rem ove t h e pa per sleeve.
(c) Apply a cceler a t or t o t h e con t a ct su r fa ce on
t h e br a cket .
(d) Allow t h e a cceler a t or t o dr y for five m in u t es.
(e) Do n ot t ou ch t h e br a cket con t a ct su r fa ce
a ft er t h e a cceler a t or h a s been a pplied.
(5) Apply a dh esive a cceler a t or t o t h e br a cket con -
t a ct su r fa ce on t h e win dsh ield gla ss. Allow t h e a ccel-
er a t or t o dr y for on e m in u t e. Do n ot t ou ch t h e gla ss
con t a ct su r fa ce a ft er
a pplied.
(6) In st a ll t h e br a cket a ccor din g t o t h e followin g
in st r u ct ion s:
t h e a cceler a t or h a s
(a ) Apply on e dr op of a dh esive a t t h e cen t er of
t h e br a cket con t a ct -su r fa ce on t h e win dsh ield
gla ss.
(b) Apply a n even coa t of a dh esive t o t h e con t a ct
su r fa ce on t h e br a cket .
(c) Align t h e br a cket wit h t h e m a r ked posit ion
on t h e win dsh ield gla ss.
(d) P r ess a n d h old t h e br a cket in pla ce for a t
lea st on e m in u t e.
NOTE: Verify that the mirror support bracket is cor-
rectly aligned, because the adhesive will cure rap-
idly.
(7) Allow t h e a dh esive t o cu r e for 8-10 m in u t es.
Rem ove a n y excess a dh esive wit h a n a lcoh ol-da m p-
en ed clot h .
(8) Allow t h e a dh esive t o cu r e for a n a ddit ion a l
8-10 m in u t es befor e in st a llin g t h e m ir r or.
ST EPWELL SCU FF PADS
REMOVAL
(1) Rem ove scr ews a n d r em ove sea t br a cket if n ec-
essa r y.
(2) Rem ove t r im plu gs a n d scr ews. (F ig. 8) a n d
(F ig. 9)
(3) Rem ove st epwell scu ffs.
Fig. 8 STEPWELL SCUFF PADS
1 - TRIM PLUGS
2 - STEPWELL
been
INTERIOR 23 - 75