Dodge Sprinter 2006 Manual page 2100

24 - 68 PLUMBING
Fig. 4 Denso 7SBU16C A/C Compressor
1 - A/C COMPRESSOR
2 - O-RING SEAL
3 - A/C SUCTION LINE
4 - BOLT
5 - RETAINING CLIP
6 - BOLT
7 - A/C DISCHARGE LINE
8 - O-RING SEAL
DENSO 10S17 A / C COMPRESSOR
WARNING: Refer to the applicable warnings and
cautions for this system before performing the fol-
lowing operation (Refer to 24 - HEATING & AIR
CONDITIONING/PLUMBING - WARNINGS) and (Refer
to 24 - HEATING & AIR CONDITIONING/PLUMBING -
CAUTIONS). Failure to follow the warnings and cau-
tions could result in possible personal injury or
death.
NOTE: The A/C compressor may be removed and
repositioned without disconnecting the refrigerant
lines or discharging the refrigerant system. Dis-
charging is not necessary if servicing the compres-
sor clutch, clutch coil or the engine.
NOTE: If an internal failure of the A/C compressor
has occurred, the receiver/drier must be replaced.
(1) Recover t h e r efr iger a n t fr om t h e r efr iger a n t
syst em (Refer t o 24 - H E ATING & AIR CONDITION-
ING/P LUMBING - STANDARD
RE F RIGE RANT SYSTE M RE COVE RY).
(2) Discon n ect a n d isola t e t h e n ega t ive ba t t er y
ca ble.
(3) Ra ise a n d su ppor t t h e veh icle.
COOLING/ACCE SSORY
RE MOVAL).
clu t ch field coil of t h e A/C com pr essor (F ig. 5).
su ct ion a n d disch a r ge lin es t o t h e A/C com pr essor.
ch a r ge lin es fr om t h e A/C com pr essor a n d r em ove
a n d disca r d t h e O-r in g sea ls.
er a n t lin e fit t in gs a n d t h e com pr essor por t s.
sor t o t h e m ou n t in g br a cket .
com pa r t m en t .
1 - REFRIGERANT LINES
2 - WIRE HARNESS CONNECTOR
3 - BOLTS (3)
4 - A/C COMPRESSOR
I N STALLAT I ON
DENSO 7SBU16C A / C COMPRESSOR
NOTE: Be certain to check the refrigerant oil level if
the A/C compressor is being replaced. See Refriger-
ant Oil Level in this group for the procedures. Use
only refrigerant oil of the type recommended for the
A/C compressor in the vehicle.
NOTE: If an internal failure of the A/C compressor
has occurred, the receiver/drier must be replaced.
P ROCE DURE -
pa r t m en t a n d loosely in st a ll t h e t h r ee com pr essor
r et a in in g bolt s. Tigh t en t h e bolt s u sin g t h e followin g
sequ en ce t o 20 N·m (15 ft . lbs.).
(4) Rem ove t h e a ccessor y dr ive belt (Refer t o 7 -
(5) Discon n ect t h e wir e h a r n ess con n ect or fr om t h e
(6) Rem ove t h e bolt s t h a t secu r e t h e u n der body
(7) Discon n ect t h e u n der body su ct ion a n d dis-
(8) In st a ll plu gs in , or t a pe over t h e open ed r efr ig-
(9) Rem ove t h e bolt s t h a t secu r e t h e A/C com pr es-
(10) Rem ove t h e A/C com pr essor fr om t h e en gin e
Fig. 5 Denso 10S17 A/C Compressor
(1) P osit ion t h e A/C com pr essor in t h e en gin e com -
DRIVE /BE LTS-DRIVE
VA
-