Function - Canon imageRUNNER ADVANCE C3325 Series Service Manual

FUNCTION

■ INSTALL
COPIER>FUNCTION>INSTALL
STIR-Y Stirring of Y-color developer
Lv.1 Details To stir developer in the Y-color Developing Unit.
Use case When fogging occurs on an image after the machine has not been
used for a long time
Adj/set/operate method Select the item, and then press OK key.
Display/adj/set range During operation: ACTIVE, When operation finished normally: OK!
Required time 150 sec
Related service mode COPIER> FUNCTION> INSTALL> STIR-M/C/K/4
STIR-M Stirring of M-color developer
Lv.1 Details To stir developer in the M-color Developing Unit.
Use case When fogging occurs on an image after the machine has not been
used for a long time
Adj/set/operate method Select the item, and then press OK key.
Display/adj/set range During operation: ACTIVE, When operation finished normally: OK!
Required time 150 sec
Related service mode COPIER> FUNCTION> INSTALL> STIR-Y/C/K/4
STIR-C Stirring of C-color developer
Lv.1 Details To stir developer in the C-color Developing Unit.
Use case When fogging occurs on an image after the machine has not been
used for a long time
Adj/set/operate method Select the item, and then press OK key.
Display/adj/set range During operation: ACTIVE, When operation finished normally: OK!
Required time 150 sec
Related service mode COPIER> FUNCTION> INSTALL> STIR-Y/M/K/4
STIR-K Stirring of Bk-color developer
Lv.1 Details To stir developer in the Bk-color Developing Unit.
Use case When fogging occurs on an image after the machine has not been
used for a long time
Adj/set/operate method Select the item, and then press OK key.
Display/adj/set range During operation: ACTIVE, When operation finished normally: OK!
Required time 150 sec
Related service mode COPIER> FUNCTION> INSTALL> STIR-Y/M/C/4
STIR-4 Stirring of all colors of developers
Lv.1 Details To stir developer in the Developing Units of 4 colors (Y/M/C/Bk).
Use case When fogging occurs on an image after the machine has not been
used for a long time
Adj/set/operate method Select the item, and then press OK key.
Display/adj/set range During operation: ACTIVE, When operation finished normally: OK!
Required time 150 sec
Related service mode COPIER> FUNCTION> INSTALL> STIR-Y/M/C/K
8
Service Mode > COPIER > FUNCTION > INSTALL
8 Service Mode > COPIER > FUNCTION > INSTALL
COPIER>FUNCTION>INSTALL
STRD-POS Scan position auto adj in DADF mode
Lv.1 Details To adjust the DADF scanning position automatically.
Use case At DADF installation/uninstallation
Adj/set/operate method 1) Close the DADF.
2) Select the item, and then press OK key.
Close the DADF until the operation automatically stops after the
adjustment.
3) Write the value displayed by COPIER> ADJUST> ADJ-XY> STRD-
POS in the service label.
Caution - If the DADF is opened before the operation automatically stops,
perform the operation again.
- Write the adjusted value in the service label.
Display/adj/set range At normal termination: OK, At abnormal termination: NG
Required time 10 sec
Related service mode COPIER> ADJUST> ADJ-XY> STRD-POS
Supplement/memo For the copyboard model, there is no need to adjust the reading
position.
CARD Setting of card number
Lv.1 Details To set the card number to be used for Card Reader.
A series of numbers from the entered number to the number of cards
specified by CARD-RNG can be used.
Use case - At installation of the Card Reader
- After replacing the HDD
Adj/set/operate method 1) Enter the number, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution The card management information (department ID and PIN) is
initialized.
Display/adj/set range 0 to 2001
Default value 0
Related service mode COPIER> OPTION> FNC-SW> CARD-RNG
8-115
8-115