Canon imageRUNNER ADVANCE C3325 Series Service Manual page 721

COPIER > OPTION > NETWORK
WUEV-SW ON/OFF of sleep notification to appli
Lv.2 Details To set whether to notify the sleep mode to the application (imageWARE,
etc) on the network when shifting to/recovering from the sleep mode.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: ON, 1: OFF
Default value 0
Related service mode COPIER> OPTION> NETWORK> WUEV-INT, WUEV-POT, WUEV-
RTR
WUEV-INT Setting of sleep notification interval
Lv.2 Details To set the interval of sleep notification.
When WUEV-SW is 0, this setting is enabled.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 60 to 65535
Unit 1 sec
Default value 600
Related service mode COPIER> OPTION> NETWORK> WUEV-SW
WUEV-POT Set port number for sleep notification
Lv.2 Details To set port number of the PC to notify the sleep mode.
When WUEV-SW is 0, this setting is enabled.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 1 to 65535
Default value 11427
Related service mode COPIER> OPTION> NETWORK> WUEV-SW
WUEV-RTR Setting of extent of sleep notification
Lv.2 Details To set the number of available routers to the target for sleep
notification.
When WUEV-SW is 0, this setting is enabled.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 254
Default value 3
Related service mode COPIER> OPTION> NETWORK> WUEV-SW
8
Service Mode > COPIER > OPTION > NETWORK
8 Service Mode > COPIER > OPTION > NETWORK
COPIER > OPTION > NETWORK
WUEN-LIV Set startup time after sleep notice
Lv.2 Details To set the time from startup from sleep mode via network without job
assignment until the mode is shifted to the sleep mode again.
Use case When setting the startup time after sleep notification
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 1 to 600
Unit 1 sec
Default value 15
IFX-CHIG Set operation by IFAX recv e-mail text
Lv.1 Details To set the number of characters for the IFAX received e-mail text, so
that the e-mail is not printed/forwarded when the characters in the
e-mail text is less than the number of specified characters.
When a sender sends e-mail text consisting of linefeed codes only,
this machine outputs a blank paper. In such case, specify 2 (number of
characters) so that there will be no output of blank paper.
In the case of specifying any number other than 0, header/footer is
printed/forwarded in 1 sheet only if the e-mail text is less than the
specified value while no TIFF file is attached.
As the value is incremented by 1, the number of target characters in
e-mail text is increased by 1 character.
Use case When reducing printouts of blank paper due to e-mail received by
IFAX
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution Be sure to get approval from the user by telling that e-mail text is not
printed if the number of characters is less than the specified value.
Display/adj/set range 0 to 999
0: E-mail text is not ignored.
Unit 1 char
Default value 0
Supplement/memo A Japanese Kanji character is calculated as 2 bytes, and the control
codes (such as linefeed code, etc) are included in the number of
characters.
DNSTRANS Setting of DNS query priority protocol
Lv.1 Details To set priority of the protocol (IPv4/IPv6) for DNS query.
In the case of using both IPv6 and IPv4 while the DNS server supports
IPv4, it takes time because of timeout when executing DNS query with
priority on IPv6. Giving priority on query by IPv4 can shorten the time.
Use case When it takes time to execute DNS query with priority on IPv6 because
the DNS server supports IPv4
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: IPv4, 1: IPv6
Default value 1
8-170
8-170