Canon imageRUNNER ADVANCE C3325 Series Service Manual page 602

COPIER>ADJUST>ADJ-XY
STRD-POS Adj read pstn in DADF mode
Lv.1 Details To adjust the reading position at DADF reading.
When replacing the Scanner Unit/clearing the RAM data of the Reader
Unit, enter the value of service label.
Use case • When replacing the Scanner Unit
• When clearing the RAM data of the Reader Unit
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
2) Turn OFF/ON the main power switch.
Caution After the setting value is changed, write the changed value in the
service label.
Display/adj/set range -100 to 100
Unit 0.1 mm
Default value 0
Related service mode COPIER> FUNCTION> INSTALL> STRD-POS
ADJ-X-MG Image ratio in book mod: vert scan
Lv.1 Details To make a fine adjustment of image magnification in vertical scanning
direction at copyboard reading.
When replacing the Scanner Unit/clearing the RAM data of the Reader
Unit, enter the value of service label.
As the value is incremented by 1, the image magnification changes by
0.1%.
+: Enlarge
-: Reduce
Use case • When replacing the Scanner Unit
• When clearing the RAM data of the Reader Unit
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
2) Turn OFF/ON the main power switch.
Caution After the setting value is changed, write the changed value in the
service label.
Display/adj/set range -5 to 5
Unit 0.1 %
Appropriate target 0
value
Default value 0
8
Service Mode > COPIER > ADJUST > CCD
T-8-20
8 Service Mode > COPIER > ADJUST > CCD
■ CCD
COPIER>ADJUST>CCD
W-PLT-X White level data(X) entry of white plate
Lv.1 Details When clearing the RAM data of the Reader Unit, enter the value of
P-PRINT. When replacing the Copyboard Glass, enter the value of
barcode label which is affixed on the glass.
Use case • When replacing the Copyboard Glass/Scanner Unit
• When clearing the RAM data of the Reader Unit
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution Output the service mode setting values by P-PRINT beforehand.
Display/adj/set range 1 to 9999
Default value 8271
Related service mode COPIER> ADJUST> CCD> W-PLT-Y, W-PLT-Z
COPIER> FUNCTION> MISC-P> P-PRINT
W-PLT-Y White level data(Y) entry of white plate
Lv.1 Details When clearing the RAM data of the Reader Unit, enter the value of
P-PRINT. When replacing the Copyboard Glass, enter the value of
barcode label which is affixed on the glass.
Use case • When replacing the Copyboard Glass/Scanner Unit
• When clearing the RAM data of the Reader Unit
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution Output the service mode setting values by P-PRINT beforehand.
Display/adj/set range 1 to 9999
Default value 8735
Related service mode COPIER> ADJUST> CCD> W-PLT-X, W-PLT-Z
COPIER> FUNCTION> MISC-P> P-PRINT
W-PLT-Z White level data(Z) entry of white plate
Lv.1 Details When clearing the RAM data of the Reader Unit, enter the value of
P-PRINT. When replacing the Copyboard Glass, enter the value of
barcode label which is affixed on the glass.
Use case • When replacing the Copyboard Glass/Scanner Unit
• When clearing the RAM data of the Reader Unit
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution Output the service mode setting values by P-PRINT beforehand.
Display/adj/set range 1 to 9999
Default value 9418
Related service mode COPIER> ADJUST> CCD> W-PLT-X, W-PLT-Z
COPIER> FUNCTION> MISC-P> P-PRINT
8-51
8-51