Canon imageRUNNER ADVANCE C3325 Series Service Manual page 482

Error■ Detail■
Location Item
code Code
E540 8001 02 Title a.■Tray■Shift■Motor■error
b.■Tray■1■timeout■error
Detection■ a.■The■Stack■Tray■Paper■Height■Sensor■was■not■turned■ON■
description although■5■seconds■had■passed■after■the■Tray■Shift■Motor■
operation■started.
b.■The■tray■does■not■return■to■its■home■position■although■the■Tray■
1■Shift■Motor■has■been■driven■for■25■seconds.
•■ The■tray■does■not■move■to■the■other■area■although■the■Tray■1■
Shift■Motor■has■been■driven■for■5■seconds.
Remedy a.■INNER■FIN-G1
[Related■parts]
•■ Harnesses■and■connectors■from■the■Finisher■Controller■PCB■to■
the■Stack■Tray■Paper■Height■Sensor
•■ Harnesses■and■connectors■from■the■Finisher■Controller■PCB■to■
the■Tray■Shift■Motor
•■ Stack■Tray■Paper■Height■Sensor■(PS9)
•■ Tray■Shift■Motor■(M6)
•■ Finisher■Controller■PCB■(PCB1)
b.■STAPLE■FIN-U1/BOOKLET■FIN-U1
[Related■parts]
•■ Harnesses■and■connectors■from■the■Finisher■Controller■PCB■to■
the■Tray■1■Paper■Surface■Sensor
•■ Harnesses■and■connectors■from■the■Finisher■Controller■PCB■to■
the■Tray■1■Shift■Area■Sensor■PCB
•■ Harnesses■and■connectors■from■the■Finisher■Controller■PCB■to■
the■Tray■1■Shift■Motor
•■ Tray■1■drive■mechanism
•■ Tray■1■Paper■Surface■Sensor■(PI114)
•■ Tray■1■Shift■Area■Sensor■PCB■(PCB4)
•■ Tray■1■Shift■Motor■(M107)
•■ Finisher■Controller■PCB■(PCB1)
[Remedy]■Check/replace■the■corresponding■harnesses/cables■or■
connectors■or■the■parts.
[Reference]■When■replacing■the■Finisher■Controller■PCB,■refer■
to■"Adjustment>■Adjustment■when■Replacing■the■Parts"■in■the■
Service■Manual.
7
Error•Jam•Alarm■>■Error■Code■>■Error■Code■Details
Description
7 Error•Jam•Alarm■>■Error■Code■>■Error■Code■Details
Error■ Detail■
Location Item
code Code
E540 8002 02 Title a.■Tray■Shift■Motor■error
b.■Tray■1■shift■area■error
Detection■ a.■The■Front■Alignment■Plate■HP■Sensor■was■not■turned■OFF■or■
description the■Stack■Tray■Lower■Limit■Sensor■was■not■turned■ON■although■
3.5■seconds■had■passed■after■the■Front■Alignment■Motor■
operation■started■in■the■tray■down■operation.
•■ The■Front■Alignment■Plate■HP■Sensor■was■not■turned■OFF■
after■the■tray■was■moved■down■in■the■paper■level■detection■
operation.■
b.■The■tray■exceeded■the■upper/lower■limit■before■the■Tray■1■
Paper■Surface■Sensor■detects■the■paper■surface■during■the■
paper■surface■detection■operation.
•■ A■non-contiguous■area■was■detected■during■the■tray■shift■
operation.
Remedy a.■INNER■FIN-G1
[Related■parts]
•■ Harnesses■and■connectors■from■the■Finisher■Controller■PCB■to■
the■Stack■Tray■Paper■Height■Sensor
•■ Harnesses■and■connectors■from■the■Finisher■Controller■PCB■to■
the■Tray■Shift■Motor
•■ Stack■Tray■Paper■Height■Sensor■(PS9)
•■ Tray■Shift■Motor■(M6)
•■ Finisher■Controller■PCB■(PCB1)
b.■STAPLE■FIN-U1/BOOKLET■FIN-U1
[Related■parts]
•■ Harnesses■and■connectors■from■the■Finisher■Controller■PCB■to■
the■Tray■1■Paper■Surface■Sensor
•■ Harnesses■and■connectors■from■the■Finisher■Controller■PCB■to■
the■Tray■1■Shift■Area■Sensor■PCB
•■ Harnesses■and■connectors■from■the■Finisher■Controller■PCB■to■
the■Tray■1■Shift■Motor
•■ Tray■1■drive■mechanism
•■ Tray■1■Paper■Surface■Sensor■(PI114)
•■ Tray■1■Shift■Area■Sensor■PCB■(PCB4)
•■ Tray■1■Shift■Motor■(M107)
•■ Finisher■Controller■PCB■(PCB1)
[Remedy]■Check/replace■the■corresponding■harnesses/cables■or■
connectors■or■the■parts.
[Reference]■When■replacing■the■Finisher■Controller■PCB,■refer■
to■"Adjustment>■Adjustment■when■Replacing■the■Parts"■in■the■
Service■Manual.
7-56
Description
7-56