Canon imageRUNNER ADVANCE C3325 Series Service Manual page 733

COPIER>OPTION>USER
RUI-RJT Connct set at invalid auth from remoteUI
Lv.2 Details To set whether to disconnect HTTP port when the machine receives
invalid authentication from remote UI 3 times.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Continued connection, 1: Disconnected
Default value 0
FREG-SW For R&D
IFAX-SZL Setting of I-Fax send size limit
Lv.2 Details To set whether to restrict data size at the time of I-Fax transmission
that does not go through the server.
When 0 is set, it is to be #830 error in the case of sending data that
exceeds the upper limit value.
In the case that the data goes through the server, the size of
transmission data is always restricted regardless of the setting.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Limited, 1: Unlimited (Restriction applies when data goes through
the server.)
Default value 1
Related user mode Function Settings> Send> E-Mail/I-Fax Settings> Maximum Data Size
for Sending
Supplement/memo Set the upper limit value for transmission data size in Settings/
Registration menu.
IFAX-PGD Set page split TX at IFax Simple mode TX
Lv.2 Details To set whether to perform split-data transmission on a page basis in
the case that the transmission size in I-Fax Simple mode exceeds the
upper limit value.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution In the case to allowing split-data transmission, be sure to receive
approval from the user in advance by explaining the following:
- No guarantee for page order on the reception side
- There is a possibility of interruption of other received jobs between
pages.
Display/adj/set range 0 to 1
0: Prohibited, 1: Allowed
Default value 0
Related user mode Function Settings> Send> E-Mail/I-Fax Settings> Maximum Data Size
for Sending
Supplement/memo Set the upper limit value for transmission data size in Settings/
Registration menu.
8
Service Mode > COPIER > OPTION > USER
8 Service Mode > COPIER > OPTION > USER
COPIER>OPTION>USER
MEAPSAFE Setting of MEAP safe mode
Lv.2 Details To set safe mode for MEAP platform.
MPSF is displayed on the Control Panel in safe mode.
In safe mode, MEAP application is stopped while just the system
application, which starts with initial state, is activated. Logs for cause
analysis of MEAP failure can be obtained.
Use case Perform system recovery processing when MEAP platform fails to be
activated due to resource conflict between MEAP applications, service
registration or use order.
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Normal mode, 1: Safe mode
Default value 0
AFN-PSWD Setting of Set/Reg menu access limit
Lv.2 Details To set whether to restrict access to Settings/Registration menu.
When 1 is set, password entry of system administrator is required after
pressing Settings/Registration key.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Without restriction, 1: With restriction (password entry required)
Default value 0
PTJAM-RC Setting of auto reprint at PDL print jam
Lv.2 Details To set whether to automatically restart printing after clearing jam that
occurs with PDL print.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Not restart printing automatically, 1: Restart
Default value 1
PDL-NCSW Set of card management for PDL print job
Lv.2 Details To set whether to make PDL print job be subject to card management
by the Card Reader.
When 1 is set, PDL print is available only when the card ID of the card
inserted to the Card Reader matches the department ID.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: PDL print is available with no card inserted.
1: PDL print is available only when the card ID of the card inserted to
the Card Reader matches the department ID.
Default value 0
8-182
8-182