Canon imageRUNNER ADVANCE C3325 Series Service Manual page 780

SORTER>ADJUST
THC-PUSH Setting heavy ppr out prev mode: Fin-U1
Lv.1 Details To set ON/OFF of heavy paper push-out prevention mode.
Set to 1 when a sheet of paper on the stack tray delivered in the
previous job is pushed out by a sheet of heavy paper delivered in the
following job.
When 1 is set and all the following conditions are satisfied, the stack
tray descends temporarily before a sheet of heavy paper is delivered
on the processing tray: *
* Specified paper in the previous job is "plain paper".
* The first-delivered paper in the following job is "heavy paper".
* The length of the above-mentioned heavy paper is more than 216
mm.
The setting is disabled in non-collate mode.
Use case When the already stacked paper is pushed out at the time of heavy
paper delivery
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 0
OFST-STC [Not used]
STP-P-CH Set stpl stack displace prev mode:Fin-U1
Lv.1 Details To set ON/OFF of staple stack displacement prevention mode.
Set to 1 when the paper on the top is misaligned in the staple delivery
mode. When 1 is set, paper stack alignment operation is executed
twice immediately before stapling.
Use case When the paper on the top is misaligned in the staple delivery mode
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 0
TRY-NIS Set tray switch noise reduct mode:Fin-U1
Lv.1 Details To set ON/OFF of tray switching noise reduction mode.
Set to 1 when the operation noise at the time of switching the Stack
Tray is loud. When 1 is set, the Stack Tray shift operation becomes
slow.
When 1 is set, tray switching speed-up mode (TRY-SU) is disabled.
Use case When the operation noise at the time of switching the Stack Tray is
loud
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 0
Related service mode SORTER> ADJUST> TRY-SU
8
Service Mode > SORTER > ADJUST
8 Service Mode > SORTER > ADJUST
SORTER>ADJUST
TRY-SU Set tray switching speedup mode: Fin-U1
Lv.1 Details To set ON/OFF of tray switching speed-up mode.
Set to 1 when the time for switching the stack tray is long. When 1
is set, the stack tray shift speed becomes faster and the productivity
improves.
When tray switching noise reduction mode (TRY-NIS) is ON, the
setting is disabled.
Use case When the Stack Tray switching time is long
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 0
Related service mode SORTER> ADJUST> TRY-NIS
FIN-NIS Set tray drive noise reduct mode: Fin-U1
Lv.1 Details To set ON/OFF of tray drive noise reduction mode.
Set to 1 when the finisher operation noise is loud. When 1 is set, the
stack tray initial operation of finisher is minimized.
Use case When the Finisher operation noise is loud
Adj/set/operate method Enter the setting value, and then press OK key.
Caution Do not use this at the normal service. (For individual measure)
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 0
1SHT-SHF Set 1-sheet stack shift sort: Fin-U1
Lv.1 Details To set ON/OFF of Offset and Collate for 1-sheet stack.
Set 1 when enabling Offset and Collate for 1-sheet stack.
Use case When Offset and Collate for 1-sheet stack is necessary
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 0
SDL-SWCH Sddl stack capacity increase mode:Fin-U1
Lv.1 Details To set ON/OFF of saddle stacking capacity increase mode.
Set to 1 when increasing the number of sets to be stacked for saddle
stitching. When 1 is set, the stacking capacity can be over the upper
limit.
When the saddle stack full alarm (SDL-ALM) is ON, the setting is
disabled.
Use case When increasing the stacking capacity for saddle stitching
Adj/set/operate method Enter the setting value, and then press OK key.
Caution When increasing the number of sets to be stacked, the movement is
not guaranteed.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 0
Related service mode SORTER> ADJUST> SDL-ALM
8-229
8-229