Canon imageRUNNER ADVANCE C3325 Series Service Manual page 786

SORTER>OPTION
SWGUP-SW Swing Unit diseng oprtn:1st thin, Fin-U1
Lv.1 Details To set whether the Swing Unit performs disengagement operation
when feeding the 1st sheet of thin paper.
By selecting 1, the Swing Unit is disengaged when the 1st sheet of
thin paper with 210 mm or less in width and 297 mm or less in length
is fed.
Use case When corner bend or delivery failures occur on the 1st sheet of thin
paper.
Adj/set/operate method Enter the setting value, and then press OK key.
Caution When 1 is set, productivity decreases.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 0
MSTP-TMG Setting of manual staple timing: Fin-G1
Lv.1 Details To set the duration of time before executing automatic stapling at
manual staple mode.
As the value is changed by 1, the time is changed by 1 second.
+: Timing is delayed
-: Timing becomes earlier
Use case Upon user's request
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 1 to 5
Unit 1 sec
Default value 3
Related user mode Adjustment/Maintenance> Adjust Action> Time Unitil Stapling Starts
in Stapler Mode
Supplement/memo The setting of the service mode links the setting of the user mode.
DWCL-BND Set the lead edge bend prev mode: Fin-U1
Lv.1 Details To set ON/OFF of leading edge corner bend prevention mode for
downward curled paper.
By selecting 1, the Alignment Plate is moved inward when a leading
sheet of a job is fed while there is no paper on the Processing Tray.
Paper is fed on the Alignment Plate so it can prevent corners of the
leading edge of paper from interfering with the rib of the Processing
Tray.
Use case When corners of the leading edge of downward curled paper is bent
Adj/set/operate method Enter the setting value and press OK key.
Caution When 1 is set, the Alignment Plate moves at staple/offset and collate
mode so productivity is decreased.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 0
8
Service Mode > SORTER > OPTION
8 Service Mode > SORTER > OPTION
SORTER>OPTION
FR-ST-PO Set staple free staple position: Fin-G1
Lv.1 Details To set the staple position of staple free stapling.
When 1 is set, staple position becomes the center so paper is more
likely to be come off. The staple position moves to the delivery
direction for 4.0 mm and the alignment direction for 2.0 mm inside.
Use case Upon user's request
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 1
0: Corner-stapling (normal), 1: Center-stapling
Default value 0
Related service mode SORTER> ADJUST >FR-STP-X, FR-STP-Y
MSTP-WT Set wait time after manual staple:Fin-G1
Lv.1 Details To set the duration of time to keep manual staple mode enabled after
execution of manual stapling.
While manual stapling mode is enabled, other jobs are not accepted.
Use case Upon user's request
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 10
Unit 1 sec
Default value 0
TRY-PSTN Set tray pstn after job complete: Fin-G1
Lv.1 Details To set the tray position after the completion of job.
When 1 is set, the tray stops at the lower limit position. Visibility of
the delivered papers is improved, but FCOT becomes longer.
Use case Upon user's request (to improve visibility of the delivered papers)
Adj/set/operate method Enter the setting value, and then press OK key.
Caution When 1 is set, FCOT becomes longer.
Display/adj/set range 0 to 1
0: Normal (priority on productivity), 1: Lower limit position (priority on
visibility)
Default value 0
Related service mode COPIER> OPTION> USER> TRY-STP
Supplement/memo When 1 in COPIER> OPTION> USER> TRY-STP is set, the tray of
the inner finisher does not down after paper full detection.
TRY-CRNT Set Stack Tray drive current VL: Fin-U1
Lv.1 Details To set the drive current value to lift the Stack Tray with a stack of
papers which paper weight is less than the equivalent of 500 sheets
of small size paper.
When 1 is set, the current value increases, so the drive torque is
increased.
Use case When stacking thin and high density papers
Adj/set/operate method Enter the setting value, and then press OK key.
Caution When 1 is set, operating noise of the Stack Tray becomes louder.
Display/adj/set range 0 to 1
0: Weak (normal), 1: Strong
Default value 0
8-235
8-235