Canon imageRUNNER ADVANCE C3325 Series Service Manual page 691

COPIER > OPTION > FNC-SW
ASLPMAX Set auto sleep shift time maximum value
Lv.1 Details To set the maximum auto sleep shift time.
Use case Upon user's request
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 1
0: 4 hours, 1: 60 minutes
Default value JP:0, USA:0, EUR:1, AU:0, CN:0, KR:0, TW:0, ASIA:0
SEND-SPD ON/OFF of SEND operation speed-up
Lv.2 Details To set whether to speed up the SEND operation.
When 1 is set, transmission speed of SEND/XBOX is increased
because image conversion is performed during SEND and Scan.
Use case When speeding up the SEND operation
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution When 1 is set, the speed may be decreased due to occurrence of
competing operation or failure with MEAP application may occur. In
such case, be sure to return the value back to 0.
Display/adj/set range 0 to 1
0: ON, 1: OFF
Default value 0
TNNEWQCK Set new Tonr Cntner chck seq aftr rplce
Lv.2 Details To set whether to execute the new Toner Container check sequence
after replacement.
In case of processing a large job immediately after replacement of
the Toner Container when 0 is set, downtime due to the new Toner
Container check sequence occurs during the processing.
When 1 is set, control to print the specified number of sheets is turned
OFF and the new Toner Container check sequence is executed
immediately after the replacement.
Use case When downtime occurs due to the new Toner Container check
sequence during the processing of a large job
Adj/set/operate method Enter the setting value, and then press OK key.
Caution Do not use this when the machine is operating correctly.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 0
Related service mode COPIER> OPTION> IMG-DEV> TNNEWCNT
2TR-TBLS Set sec transfer bias correction table
Lv.1 Details To set the secondary transfer bias correction table according to the
paper to be used.
Since physical properties of paper are different for each location, use
the table according to the paper to be used.
Use case When using paper for a location other than the intended one
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 2
0: For Japan, 1: For locations other than Japan and USA, 2: For USA
Default value JP:0, USA:2, EUR:1, AU:1, CN:1, KR:1, TW:1, ASIA:1
8
Service Mode > COPIER > OPTION > FNC-SW
8 Service Mode > COPIER > OPTION > FNC-SW
COPIER > OPTION > FNC-SW
VER-CHNG Setting of firmware update operation
Lv.2 Details To set how to update firmware of PCB/option which has been installed/
replaced by comparing the version of it with the version stored in the
Flash PCB of the Main Controller.
If combination of firmware versions of PCB/option stored in the Main
Controller and the version in PCB/option after installation/replacement
is not appropriate (operation with the combination of firmware versions
has not yet been checked), failure where analysis is difficult may occur.
It is possible to check the firmware versions at the start of the machine,
and automatically write the firmware stored in the Main Controller in
PCB/option collectively as needed.
When 0 is set, versions are not checked and firmware update is not
performed. Therefore, it is necessary to manually update the versions
using a USB memory/SST.
When 1 is set, firmware is updated if the version in PCB/option is old.
However, it is not updated if the version is new or old and new versions
are mixed.
When 2 is set, a compatible firmware (the version where operation
has been checked) is written from the Main Controller regardless of
whether the version in PCB/option is old or new.
Use case When installing/replacing PCB/option having firmware
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 2
0: Keep the current firmware version.
1: Update the firmware if the version in PCB/option is older than that
stored in the Main controller. If the version is new or old and new
versions are mixed, firmware is not updated.
2: Update the firmware regardless of whether the version is old or
new if the version in PCB/option differs from that stored in the Main
Controller.
Default value 1
Supplement/memo When updating the firmware, the main menu is displayed on the
Control Panel at startup and then a message prompting to update
firmware is displayed.
By pressing [Update], the machine reboots immediately and firmware
is updated.
By pressing [Skip], it returns to the main menu. The message is
displayed again at next startup.
8-140
8-140