Canon imageRUNNER ADVANCE C3325 Series Service Manual page 636

COPIER>ADJUST>HV-TR
TR-ENV5 Sec trns indiv setting environment:set 5
Lv.2 Details To set the environment (absolute moisture content) for setting 5.
Setting 5 is the combination condition of environment, paper type (paper
weight), color mode/feed side that are set in TR-ENV5, TR-PPR5 and
TR-DUP5. When this condition is satisfied, the paper allotted voltage
adjusted in TR-VL5 is applied at the time of secondary transfer.
Use case When an image failure that differs due to the environment occurs
(mottled image/density loss due to excessive transfer/toner scattering
on solid image, etc.)
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 1 to 3
1: Low humidity (absolute moisture content: 6.11 g/m3 or less), 2:
Normal humidity (6.12 to 15.68 g/m3), 3: High humidity (15.69 g/m3 or
higher)
Default value 1
Related service mode COPIER> ADJUST> HV-TR> TR-PPR5, TR-DUP5, TR-VL5, 2TR-OFF
Supplement/memo Up to 16 combination patterns can be set in TR-VL1 to 16 (setting
1 to 16). When there is more than one setting where all conditions
(environment, paper type and color mode/feed side) are the same, the
setting with a smaller setting number is applied.
TR-ENV6 Sec trns indiv setting environment:set 6
Lv.2 Details To set the environment (absolute moisture content) for setting 6.
Setting 6 is the combination condition of environment, paper type (paper
weight), color mode/feed side that are set in TR-ENV6, TR-PPR6 and
TR-DUP6. When this condition is satisfied, the paper allotted voltage
adjusted in TR-VL6 is applied at the time of secondary transfer.
Use case When an image failure that differs due to the environment occurs
(mottled image/density loss due to excessive transfer/toner scattering
on solid image, etc.)
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 1 to 3
1: Low humidity (absolute moisture content: 6.11 g/m3 or less), 2:
Normal humidity (6.12 to 15.68 g/m3), 3: High humidity (15.69 g/m3 or
higher)
Default value 1
Related service mode COPIER> ADJUST> HV-TR> TR-PPR6, TR-DUP6, TR-VL6, 2TR-OFF
Supplement/memo Up to 16 combination patterns can be set in TR-VL1 to 16 (setting
1 to 16). When there is more than one setting where all conditions
(environment, paper type and color mode/feed side) are the same, the
setting with a smaller setting number is applied.
8
Service Mode > COPIER > ADJUST > HV-TR
8 Service Mode > COPIER > ADJUST > HV-TR
COPIER>ADJUST>HV-TR
TR-ENV7 Sec trns indiv setting environment:set 7
Lv.2 Details To set the environment (absolute moisture content) for setting 7.
Setting 7 is the combination condition of environment, paper type (paper
weight), color mode/feed side that are set in TR-ENV7, TR-PPR7 and
TR-DUP7. When this condition is satisfied, the paper allotted voltage
adjusted in TR-VL7 is applied at the time of secondary transfer.
Use case When an image failure that differs due to the environment occurs
(mottled image/density loss due to excessive transfer/toner scattering
on solid image, etc.)
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 1 to 3
1: Low humidity (absolute moisture content: 6.11 g/m3 or less), 2:
Normal humidity (6.12 to 15.68 g/m3), 3: High humidity (15.69 g/m3 or
higher)
Default value 1
Related service mode COPIER> ADJUST> HV-TR> TR-PPR7, TR-DUP7, TR-VL7, 2TR-OFF
Supplement/memo Up to 16 combination patterns can be set in TR-VL1 to 16 (setting
1 to 16). When there is more than one setting where all conditions
(environment, paper type and color mode/feed side) are the same, the
setting with a smaller setting number is applied.
TR-ENV8 Sec trns indiv setting environment:set 8
Lv.2 Details To set the environment (absolute moisture content) for setting 8.
Setting 8 is the combination condition of environment, paper type (paper
weight), color mode/feed side that are set in TR-ENV8, TR-PPR8 and
TR-DUP8. When this condition is satisfied, the paper allotted voltage
adjusted in TR-VL8 is applied at the time of secondary transfer.
Use case When an image failure that differs due to the environment occurs
(mottled image/density loss due to excessive transfer/toner scattering
on solid image, etc.)
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 1 to 3
1: Low humidity (absolute moisture content: 6.11 g/m3 or less), 2:
Normal humidity (6.12 to 15.68 g/m3), 3: High humidity (15.69 g/m3 or
higher)
Default value 1
Related service mode COPIER> ADJUST> HV-TR> TR-PPR8, TR-DUP8, TR-VL8, 2TR-OFF
Supplement/memo Up to 16 combination patterns can be set in TR-VL1 to 16 (setting
1 to 16). When there is more than one setting where all conditions
(environment, paper type and color mode/feed side) are the same, the
setting with a smaller setting number is applied.
8-85
8-85