Canon imageRUNNER ADVANCE C3325 Series Service Manual page 703

COPIER > OPTION > IMG-FIX
PLN-LP Set fix arch ctrl: pln,color,rcycl,punch
Lv.2 Details To set the arch amount between the secondary transfer and fixing
when feeding plain paper 1/2/3, colored paper, recycled paper 1/2/3
and pre-punched paper at 1/1 speed.
Increase the value when an image failure (crawled marks/wrinkles)
occurs.
Use case When an image failure (crawled marks/wrinkles) occurs with plain
paper, colored paper, recycled paper and pre-punched paper
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and press
OK key.
Display/adj/set range -2 to 2
-2: 0 mm, -1: 15 mm, 0: 35 mm, 1: 60 mm, 2: 85 mm
Default value 0
TRC-LP Set fixing arch control: tracing paper
Lv.2 Details To set the arch amount between the secondary transfer and fixing
when feeding tracing paper at 1/1 speed.
Increase the value when an image failure (crawled marks/wrinkles)
occurs.
Use case When an image failure (crawled marks/wrinkles) occurs with tracing
paper
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and press
OK key.
Display/adj/set range -2 to 2
-2: 0 mm, -1: 15 mm, 0: 35 mm, 1: 60 mm, 2: 85 mm
Default value 0
FXS-TM12 Set ITOP control temp: plain paper 3
Lv.1 Details To set the offset of ITOP control temperature for plain paper 3 (91 to
105 g/m2).
As the value is changed by 1, the control temperature is changed by 5
deg C.
Decrease the value when uneven gloss occurs, and increase the value
when a fixing failure occurs on the leading edge of paper.
Use case - When a fixing failure occurs on the leading edge of paper
- When uneven gloss occurs on the leading edge (74 mm)
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and press
OK key.
Caution If the value is too large, uneven gloss may occur.
If the value is too small, a fixing failure may occur on the leading edge
of paper. (Toner does not peel off.)
Display/adj/set range -2 to 2
-2: -10 deg C, -1: -5 deg C, 0: 0 deg C, 1: +5 deg C, 2: +10 deg C
Unit 5 deg C
Default value 0
8
Service Mode > COPIER > OPTION > IMG-FIX
8 Service Mode > COPIER > OPTION > IMG-FIX
COPIER > OPTION > IMG-FIX
FXS-TM13 Set ITOP control temp: recycled paper 2
Lv.1 Details To set the offset of ITOP control temperature for recycled paper 2 (76
to 90 g/m2).
As the value is changed by 1, the control temperature is changed by 5
deg C.
Decrease the value when uneven gloss occurs, and increase the value
when a fixing failure occurs on the leading edge of paper.
Use case - When a fixing failure occurs on the leading edge of paper
- When uneven gloss occurs on the leading edge (74 mm)
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and press
OK key.
Caution If the value is too large, uneven gloss may occur.
If the value is too small, a fixing failure may occur on the leading edge
of paper. (Toner does not peel off.)
Display/adj/set range -2 to 2
-2: -10 deg C, -1: -5 deg C, 0: 0 deg C, 1: +5 deg C, 2: +10 deg C
Unit 5 deg C
Default value 0
FXS-TM14 Set ITOP control temp: recycled paper 3
Lv.1 Details To set the offset of ITOP control temperature for recycled paper 3 (91
to 105 g/m2).
As the value is changed by 1, the control temperature is changed by 5
deg C.
Decrease the value when uneven gloss occurs, and increase the value
when a fixing failure occurs on the leading edge of paper.
Use case - When a fixing failure occurs on the leading edge of paper
- When uneven gloss occurs on the leading edge (74 mm)
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and press
OK key.
Caution If the value is too large, uneven gloss may occur.
If the value is too small, a fixing failure may occur on the leading edge
of paper. (Toner does not peel off.)
Display/adj/set range -2 to 2
-2: -10 deg C, -1: -5 deg C, 0: 0 deg C, 1: +5 deg C, 2: +10 deg C
Unit 5 deg C
Default value 0
8-152
8-152