Canon imageRUNNER ADVANCE C3325 Series Service Manual page 688

COPIER > OPTION > FNC-SW
SDLMTWRN ON/OFF cpcty warn dspl: E-mail/I-Fax TX
Lv.2 Details To set whether to display the warning message when sending data that
exceeds the upper limit of the transmission data size via E-mail/I-Fax.
Use case For customization
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 0
Related user mode Function Settings> Send> E-Mail/I-Fax Settings> Maximum Data Size
for Sending
AUTO-OUT ON/OFF of jammed ppr auto ejctn function
Lv.1 Details To set ON/OFF of jammed paper automatic ejection function.
When 1 is set, jammed paper is not delivered to the ejection position,
but it stays at the current position at jam occurrence.
Use case - When user does not need automatic ejection of jammed paper
- When location of jammed paper is necessary to analyze the cause of
a problem
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 1
0: ON, 1: OFF
Default value 0
JLK-PWSC ON/OFF of PCAM password auth doc scan
Lv.2 Details To set whether to scan the PCAM password authentication document
with the MEAP application.
Use case When scanning the PCAM password authentication document
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 0
FAX-INT Set FAX RX print interruption oprtn mode
Lv.2 Details To set the mode performing interruption operation of FAX reception
print automatically.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution - Do not set this item while charge management (charging by Coin
Manager, a device alone, etc.) is used.
- During an ongoing job for which delivery setting (offset, stapling, etc.)
is made, interruption operation is performed between sets.
Display/adj/set range 0 to 1
0: Normal, 1: Interruption operation mode
Default value 0
8
Service Mode > COPIER > OPTION > FNC-SW
8 Service Mode > COPIER > OPTION > FNC-SW
COPIER > OPTION > FNC-SW
PDL-Z-LG Setting of drawing algorithm
Lv.1 Details To switch the drawing algorithm of the iR C series and the iR-ADV C
series to obtain output expected by the user.
When 0 is set, image is output as displayed on the screen by the new
algorithm adopted from the iR-ADV C Series. Pseudo outline (boundary
for processing divided graphics separately) occurred with the iR C
series does not occur. However, when PDL job with special data
structure is sent, output expected by the user may not be obtained.
When 1 is set, the drawing algorithm adopted by the conventional iR
C series is used. Output equivalent to that of the iR C Series can be
obtained; however, drawing-related phenomenon occurred with the
series occurs.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution Do not use setting value 2 and 3.
Display/adj/set range 0 to 3
0: Drawing algorithm of iR-ADV C series, 1: Drawing algorithm of the
conventional iR C series, 2, 3: For R&D use
Default value 0
CDS-LVUP Set to allow CDS periodical update
Lv.1 Details To set whether to allow the user (administrator) to perform periodical
update linked with CDS.
When 1 is set, setting of periodical update can be made in Settings/
Registration menu/via remote UI.
When 2 is set, setting of periodical update can be made on the
Updater screen in service mode.
Use case When allowing the user/service technician to perform periodical update
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution Do not set 1 for Japanese models. It is not assumed that the user
performs firmware update.
Display/adj/set range 0 to 2
0: Prohibited periodical update
1: Display the periodical update setting screen in Settings/Registration
menu/on remote UI
2: Display the periodical update setting screen on the Updater in
service mode
Default value JP:0, USA:0, EUR:1, AU:0, CN:0, KR:0, TW:0, ASIA:0
Related service mode Updater
Related user mode Management Settings> License/Other> Register/Update Software>
Periodical Update
Supplement/memo CDS: Contents Delivery System
8-137
8-137