Canon imageRUNNER ADVANCE C3325 Series Service Manual page 646

COPIER>ADJUST>HV-TR
TR-ENV13 Sec trn indiv setting environment:set 13
Lv.2 Details To set the environment (absolute moisture content) for setting 13.
Setting 13 is the combination condition of environment, paper type (paper
weight), color mode/feed side that are set in TR-ENV13, TR-PPR13 and
TR-DUP13. When this condition is satisfied, the paper allotted voltage
adjusted in TR-VL13 is applied at the time of secondary transfer.
Use case When an image failure that differs due to the environment occurs
(mottled image/density loss due to excessive transfer/toner scattering
on solid image, etc.)
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 1 to 3
1: Low humidity (absolute moisture content: 6.11 g/m3 or less), 2:
Normal humidity (6.12 to 15.68 g/m3), 3: High humidity (15.69 g/m3 or
higher)
Default value 1
Related service mode COPIER> ADJUST> HV-TR> TR-PPR13, TR-DUP13, TR-VL13, 2TR-
OFF
Supplement/memo Up to 16 combination patterns can be set in TR-VL1 to 16 (setting
1 to 16). When there is more than one setting where all conditions
(environment, paper type and color mode/feed side) are the same, the
setting with a smaller setting number is applied.
TR-ENV14
Sec trn indiv setting environment:set 14
Lv.2 Details To set the environment (absolute moisture content) for setting 14.
Setting 14 is the combination condition of environment, paper type (paper
weight), color mode/feed side that are set in TR-ENV14, TR-PPR14 and
TR-DUP14. When this condition is satisfied, the paper allotted voltage
adjusted in TR-VL14 is applied at the time of secondary transfer.
Use case When an image failure that differs due to the environment occurs
(mottled image/density loss due to excessive transfer/toner scattering
on solid image, etc.)
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 1 to 3
1: Low humidity (absolute moisture content: 6.11 g/m3 or less), 2:
Normal humidity (6.12 to 15.68 g/m3), 3: High humidity (15.69 g/m3 or
higher)
Default value 1
Related service mode COPIER> ADJUST> HV-TR> TR-PPR14, TR-DUP14, TR-VL14, 2TR-
OFF
Supplement/memo Up to 16 combination patterns can be set in TR-VL1 to 16 (setting
1 to 16). When there is more than one setting where all conditions
(environment, paper type and color mode/feed side) are the same, the
setting with a smaller setting number is applied.
8
Service Mode > COPIER > ADJUST > HV-TR
8 Service Mode > COPIER > ADJUST > HV-TR
COPIER>ADJUST>HV-TR
TR-ENV15 Sec trn indiv setting environment:set 15
Lv.2 Details To set the environment (absolute moisture content) for setting 15.
Setting 15 is the combination condition of environment, paper type (paper
weight), color mode/feed side that are set in TR-ENV15, TR-PPR15 and
TR-DUP15. When this condition is satisfied, the paper allotted voltage
adjusted in TR-VL15 is applied at the time of secondary transfer.
Use case When an image failure that differs due to the environment occurs
(mottled image/density loss due to excessive transfer/toner scattering
on solid image, etc.)
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 1 to 3
1: Low humidity (absolute moisture content: 6.11 g/m3 or less), 2:
Normal humidity (6.12 to 15.68 g/m3), 3: High humidity (15.69 g/m3 or
higher)
Default value 1
Related service mode COPIER> ADJUST> HV-TR> TR-PPR15, TR-DUP15, TR-VL15, 2TR-
OFF
Supplement/memo Up to 16 combination patterns can be set in TR-VL1 to 16 (setting
1 to 16). When there is more than one setting where all conditions
(environment, paper type and color mode/feed side) are the same, the
setting with a smaller setting number is applied.
TR-ENV16
Sec trn indiv setting environment:set 16
Lv.2 Details To set the environment (absolute moisture content) for setting 16.
Setting 16 is the combination condition of environment, paper type (paper
weight), color mode/feed side that are set in TR-ENV16, TR-PPR16 and
TR-DUP16. When this condition is satisfied, the paper allotted voltage
adjusted in TR-VL16 is applied at the time of secondary transfer.
Use case When an image failure that differs due to the environment occurs
(mottled image/density loss due to excessive transfer/toner scattering
on solid image, etc.)
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 1 to 3
1: Low humidity (absolute moisture content: 6.11 g/m3 or less), 2:
Normal humidity (6.12 to 15.68 g/m3), 3: High humidity (15.69 g/m3 or
higher)
Default value 1
Related service mode COPIER> ADJUST> HV-TR> TR-PPR16, TR-DUP16, TR-VL16, 2TR-
OFF
Supplement/memo Up to 16 combination patterns can be set in TR-VL1 to 16 (setting
1 to 16). When there is more than one setting where all conditions
(environment, paper type and color mode/feed side) are the same, the
setting with a smaller setting number is applied.
8-95
8-95